Rotary Accessories

Transcription

Rotary Accessories

FOREDOM
®
Rotary Accessories
2015
Work on
Everything
Safety Instructions
Before using your Foredom® power tool with any of the accessories shown in this catalog, please read all
safety instructions. They are for your protection and should always be followed to reduce the risk of personal
injury or damage to the tool.
It is Extremely Important to Follow these Instructions:
• Always wear proper eye and face protection. Wear
• Pay close attention to the maximum speed listed for
safety glasses or face shields whenever you operate a
Foredom or any power tool to prevent serious eye or
face injuries.
an accessory and never exceed this rating. Maximum
speed is the highest speed at which an accessory can
safely be run. If used at higher speeds, an accessory can
fly apart, bend, or self destruct, resulting in possible
serious injury to the operator or a bystander.
• Always use a proper dust collection system or wear
a respirator to prevent the inhalation of dust particles,
polishing compounds, or other debris produced from
abrasive accessories into the lungs.
• Do not wear loose fitting clothing or jewelry. Loose
clothing or jewelry can become entangled in the rotating accessory. Be sure to tie back or secure long hair.
• Accessories in this catalog are rated for use at speeds
indicated with a 1″ (25mm) overhang or less. Overhang
is the distance from the front of collet or chuck jaw to
the tip or point of the bur, mounted abrasive, or other
rotary accessory.
• Never operate any accessory at speeds above its
• Extra care should be used with an accessory that has a
lower maximum speed rating than the speed of the motor. When properly used, all of Foredom’s accessories can
be operated at the speed ratings listed in this Catalog
or on packaging. Always find out the manufacturer’s
speed rating before using accessories other than those
from Foredom.
• Rotary accessories last longer and provide their best
performance by applying gentle but firm pressure to
the workpiece and letting the speed of the motor do
the work.
maximum rated speed.
Part Numbers and Prices are shown in red on each page.
Safety Products
Made in USA
A-6103-10 $6.60/10-Pk
Soft Foam Ear Plugs
Made of hypo-allergenic
materials, these soft foam ear
plugs have a tapered shape for
a good fit and comfort. Plastic
cord prevents tangling.
A-6106-6 $25.20/6-Pk
3M Particulate Respirator
3-panel respirator with low
profile design that folds flat
and fits a wide range of face
sizes. Comfortable, lightweight
and convenient. Has Cool
FlowTM Exhalation Valve for
working in heat and humidity.
AK6100 $27.30 Safety Kit
Use this collection of safety products while running your Foredom or
other power tool. Includes:
A-SG3 Safety Glasses , A-6102 Roll of Vetrap tape, A-6103 Foam Ear
Plugs (3) and A-6106 Respirators (3)
A-6102 $4.50/Roll
3M Vetrap Tape
Self-adhering tape is easy to apply and requires no pins, clips or adhesive to keep
secure. Tape won’t loosen over
time and stays in place until
removed. Doesn’t stick to hair,
skin, or anything else. Use to
protect fingers during close
work with sharp instruments. 2″ wide x 15′ long.
A-SG3 $17.85
Safety Glasses
Clear polycarbonate glasses with a contemporary style and unitary lens design. Temples are length adjustable with slotted ends.
Cover Photo Credits:
Detail of Carved Wooden Face–James Travers, Glass Vessels– Russell Carson, Designs in Egg Shells– Katie Geerling
Always Wear Eye and Dust Protection While Using Rotary Power Tools and Accessories
2
FOREDOM®
FOREDOM ELECTRIC CO.
V Stones
Made in USA. 45,000 RPM Max Speed
Made with a vitrified, self-sharpening, special aluminum oxide grain with a super hard porous
bond, V Stones are the coolest running and longest lasting abrasive stones. They easily cut hard
metals like titanium, chrome-cobalt, nickel-cobalt, tool steel, and stainless steel, and softer
metals such as lead, pewter, brass and aluminum with minimal smearing and loading. V Stones
also work on ceramic tile, porcelain, wood, acrylic, glass, and marble. They can be used to shape,
texture, and provide detail to carvings. Their larger head sizes and coarser grits make them more
aggressive than our CeramCut Blue Stones. They are an economical alternative to plated and
sintered diamond points.
3/32″ (2.35 mm) Shank Mounted Points $3.60 Ea
Part Nos. for 40/60 & 80 Grit Shapes shown separately
overall length
Part Numbers and
Prices are shown in
red on each page.
Greg Cullen using a Ball shaped V Stone to customize
the frame of a car for a mounting bracket.
A-10076 $5 2″ V Stone Wheel with 1/4″
arbor hole
Tapered
Flat Top
Bud
Ball
Cylinder
Wheel
Taper Shape
A-V326A-V336A-V356 N/A
N/A40/60 Grit
A-V327A-V337A-V357 A-V367 A-V397 80 Grit
1/2″ (13)1/4 (6.4) Head Dia.″ (mm)
1/4″ (6.4) 3/8″ (9.5)1/4″ (6.4) 3/8″ (9.5) 3/8″ (9.5)1/2″ (13) 3/16″ (4.8)1/2″ (13) Head Length″ (mm)
1-7/8″ (47.6) 1-7/8″ (47.6)1-15/16″ (49.2) 1-3/4″ (44.5)2″ (50.8) Overall Length″ (mm)
Use with A-WM5 or A-WM6 Wheel Mandrels
at 7,000 RPM Max Speed on BL Bench Lathe,
see V Stone and more wheels on page 33.
See Power Tool Catalog or www.foredom.net
for Bench Lathe Components and Accessories
CeramCut Blue Stones have a unique ceramic and aluminum
oxide grain structure. They are widely used on hard metals,
including hardened and mild steel, steel alloys, chrome cobalt,
titanium, platinum, and other ferrous metals. Also suitable for
use on porcelain materials and wood. CeramCut Blue Stones
maintain their shape and hold their cutting edge longer than
any standard abrasive stones. They are non-impregnating and
non-contaminating.
See CeramCuts with 1/8″ shanks on next page.
3/32″ (2.35 mm) Shank
Mounted Points $2.60 Ea
overall length
CeramCut Blue Stones
Small
Tapered Large Flat Small Flat Round Top Round Top
Cylinder WheelTaperTaper
Shape Part No. A-CK352*A-CK360 A-CK390 A-CK392*A-CK396 A-CK398
Grit 120 fine 120 fine
120 fine
120 fine
120 fine
80 med
Head Dia.″ (mm) 3/32 (2.35)1/2 (13)1/8 (3.2)3/32 (2.35)1/8 (3.2)1/8 (3.2) Head Length″ (mm) 1/4 (6.4)1/8 (3.2)1/2 (13)3/16 (4.8)1/2 (13)1/2 (13)
Overall Length″ (mm) 1-3/4 (44.5) 1-3/4 (44.5)1-15/16 (49.2) 1-3/4 (44.5)1-15/16 (49.2) 1-15/16 (49.2)
CeramCuts with * are in Kit AKHK29 on next page.
Large
Medium
Ball Nose
Small
Flame
Inverted
Cone
Ball
Tapered
Cone
Large
Cylinder
Shape
A-CK300*A-CK301*A-CK302*A-CK318*A-CK322* A-CK375A-CK332*A-CK342*A-CK350 A-CK354 A-CK356
Part No.
80 med 120 fine
120 fine 80 med 120 fine 120 fine 120 fine 120 fine 120 fine 80 med 60 coarse Grit
1/4 (6.4)3/16 (4.8)1/8 (3.2)5/32 (3.9)1/8 (3.2)1/4 (6.4)1/8 (3.2)1/8 (3.2)1/4 (6.4)1/4 (6.4)1/4 (6.4)
Head Dia.″ (mm)
1/2 (13)1/2 (13)1/2 (13)3/8 (9.5)1/8 (3.2)1/4 (6.4)1/8 (3.2)1/4 (6.4)1/2 (13)1/2(13)1/2 (13) Head Length″ (mm)
2 (50.8) 1-15/16 (49.2)1-15/16 (49.2) 1-7/8 (47.6)1-5/8 (41.3) 1-3/4 (44.5)1-5/8 (41.3) 1-3/4 (44.5) 2 (50.8)
2 (50.8) 1-15/16 (49.2) Overall Length″ (mm)
FOREDOM®
3
CeramCut Blue Stones Made in USA. 45,000 RPM Max Speed
overall length
1/8″ (3.18 mm) Shank Individual Mounted Points $2.60 Ea
Large
Part Numbers and Prices are shown
in red on each page.
CeramCuts with
* are in Kit
AKHK28 shown
below
Medium
Small
Ball Nose
Flame
Small
Ball
Flat
Taper
Small Cylinder Shape
A-CK8300 A-CK8301 A-CK8302 A-CK8318 A-CK8332 A-CK897*A-CK8144* Part No.
80 med
120 fine
80 med
80 med
120 fine 120 fine 120 fine Grit
Head Dia.″ (mm)
1/4 (6.4)3/16 (4.8)1/8 (3.2)5/32 (3.9)1/8 (3.2)3/32 (2.35)1/8 (3.2) 1/2 (13)1/2 (13)1/2 (13)3/8 (9.5)1/8 (3.2)3/8 (9.5) 1/4 (6.4) Head Length″ (mm)
1-15/16 (49.2)1-15/16 (49.2)1-15/16 (49.2) 1-7/8 (47.6)1-5/8 (41.3) 1-7/8 (47.6) 1-3/4 (44.5) Overall Length″ (mm)
Pear
Ball Nose
Tree
Long
Medium
Cylinder
Wagner Dental Lab of Danbury, CT
uses CeramCut Blue Stones for grinding
chrome cobalt on flexible partial.
CeramCuts with * are in Kit AKHK28 shown below
Cup
Flame
Large
Ball Taper
Wheel
Shape
Part No.
A-CK8112A-CK890*A-CK852*A-CK8154 A-CK8175A-CK8132* A-CK846 A-CK8122* A-CK844* A-CK8182*
120 fine
80 med
120 fine 80 med
80 med
80 med
120 fine 120 fine
120 fine
120 fine Grit
Head Dia.″ (mm)
3/8 (9.5)1/2 (13)3/8 (9.5)3/16 (4.8)3/8 (9.5)3/8 (9.5)1/8 (3.2) 3/8 (9.5)7/32 (5.5)1/2 (13)
1/2 (13)1/2 (13)3/4 (19)1/2 (13)3/8 (9.5)1/2 (13)5/16 (8.0) 3/8 (9.5)
3/8 (9.5)
1/8 (3.2) Head Length″ (mm)
1-15/16 (49.2)2 (50.8)2-5/16 (48.7) 2 (50.8)1-13/16 (46) 1-15/16 (49.2) 1-5/16 (33.3) 1-7/8 (47.6) 1-7/8 (47.6) 1-3/4 (44.5) Overall Length″ (mm)
3/32″ (2.35 mm) Shank Kit, 9-Pc AKHK29 $22.50
1/8″ (3.18 mm) Shank Kit, 8-Pc AKHK28 $22.50
A-CK300
Lg Ball Nose
A-CK301
Med Ball Nose
A-CK302
Sm Ball Nose
A-CK318Flame
A-CK322
Inverted Cone
A-CK332Ball
A-CK342
Tapered Cone
A-CK352
Sm Cylinder
A-CK392
Sm Flat Taper
A-CK8122 Lg Ball
A-CK8132 Cylinder Cup
A-CK8144 Sm Cylinder
A-CK8182Wheel
A-CK844Taper
A-CK852Tree
A-CK890
Ball Nose
A-CK897
Flat Taper
Med
Fine
Fine
Med
Fine
Fine
Fine
Fine
Fine
Fine
Med
Fine
Fine
Fine
Fine
Med
Fine
2″ CeramCut Wheels for BL Bench Lathe & Angle Grinder, 11,600 RPM Max Speed
A-10064 $5
A-10065 $8.90
2″ CeramCut Blue
Wheel with 3/8″ arbor
hole, 120 grit. For use
with Angle Grinder Attachment. See Page 28.
2″ CeramCut Blue
Cup Wheel with
3/8″ arbor hole,
100 grit. For use
with Angle Grinder
Attachment. See
Page 28.
Wheels with 3/8″ arbor holes are used on Angle Grinder
and Mount with A-69212L Long Hub. See Page 20.
4
FOREDOM®
A-10074 $5
2″ CeramCut Blue
Wheel with 1/4″
arbor hole, 120
grit. For use with
M.BL Lathe. See
Page 33.
Wheel with 1/4″ arbor hole is used on BL
Bench Lathe and Mounts with A-WM5 or
A-WM6 Wheel Mandrels.
Aluminum Oxide Mounted Points
Red Individual Points
Red Aluminum Oxide mounted points are used for fast cutting on
high tensile, tough materials such as steel and malleable iron. Also
used on porcelain and glass. For medium to fine finishing work. Be
sure to specify Red Part Nos. when ordering.
AK150 $40 19-Pc Kit
Red Mounted Points
3/32″ shanks
AK160 $40 19-Pc Kit
White Mounted Points
3/32″ shanks
White Individual Points
White Aluminum Oxide mounted points of extremely fine grit (400)
for a high finish on high tensile, tough materials including gemstone,
stainless steel and glass. Extremely fine cutting. Points hold their
geometry well. Be sure to specify White Part Nos. when ordering.
overall length
Part Numbers
and Prices are
shown in red on
each page.
Red Aluminum Oxide Part Nos. and Grits
A-1 A-2 A-3A-4 A-5A-6 A-8A-9A-10
A-11A-12
Red Part No.
Grit
120 120 120100 80 80 80 120120120 100
White Aluminum Oxide Part Nos. and Grits
A-71 A-72 A-73A-74 A-75A-76 A-78A-79A-80A-81 A-82
White Part No.
Grit
400 400 400400 400400 400400400400 400
1/8 (3.2)5/16 (7.9)1/4 (6.4)1/4 (6.4)1/4 (6.4)3/16 (4.8)1/2 (13)3/8 (9.5)5/32 (4.0)1/4 (6.4) 13/64 (5.2) Head Dia.″ (mm)
7/32 (5.6)1/32 (.79)11/32 (8.7)1/4 (6.4)1/2 (13)17/32 (13.5)1/16 (1.6)3/64 (1.2)7/32 (5.6)5/64 (2.0) 13/64 (5.2) Head Length″ (mm)
1-3/4 (44.5)1-3/4 (44.5)1-7/8 (47.6) 1-7/8 (47.6)2 (50.8)
2 (50.8) 1-3/4 (44.5) 1-3/4 (44.5) 1-3/4 (44.5) 1-5/8 (41.3) 1-3/4 (44.5) Overall Length″ (mm)
Unmounted A-G27 has 1/16″ arbor hole.
Use for grinding, cleaning & smoothing
very hard materials such as steel and
malleable iron. 21,000 RPM Max Speed
Use with Mandrels A-M1, A-M6, A-M13, M15 A-M19. See pg 18.
A-M6
$1.15
Red Part No.
A-13
A-15
A-16
A-17
A-18
A-19
A-20
A-21
A-G27 Grit
100120100 120 80 120 15010080
Red Aluminum Oxide Part Nos. and Grits
White Aluminum Oxide Part Nos. and Grits
Part No.
A-83A-85A-86 A-87 A-88 A-89 A-90A-91 N/A White
Grit
400400400 400 400 400 400400 N/A
5/32 (4.0)1/8 (3.2)5/64 (2.0)1/8 (3.2)1/4 (6.4)1/8 (3.2)3/16 (4.8)1/4 (6.4)
1/4 (6.4)1/8 (3.2)17/64 (6.7)9/32 (7.1)9/32 (7.1)13/32 (10.3)5/32 (4.0)1/4 (6.4)
1-3/4 (44.5)1-3/4 (44.5)1-3/4 (44.5) 1-3/4 (44.5)1-13/16 (46) 1-7/8 (47.6) 1-11/16 (42.9) 1-3/4 (44.5)
Latch Type Burs
Red Aluminum Oxide
Head Dia.″ (mm)
Head Length″ (mm)
Overall Length″ (mm)
3/4 (19)
13/64 (5.2)
–
Green Silicon Carbide
$2.60 Ea
for Discontinued Angle Head Handpieces
H.55A, H.55D, H.56A, H.56D
Part
No.
A-RA11 A-RA12A-RA21 A-RA31 A-RA41 A-RA42
Head
1/4
3/16
Dia.″
1/4 3/161/4 1/8
Head Lgth″
1/4
7/64
3/16
7/64
3/16
5/16
120 100 120
150 150 120Grit
FOREDOM®
5
Premium Plated Diamond Points
Made in Belgium
Part Numbers and Prices are shown in red.
2.35 mm (3/32″) Shank Mounted Plated Points Priced Below 120,000 RPM Max Speed
overall length
Premium quality Dumont Plated Diamond points have precision turned steel blanks to ensure proper concentricity and balance for high speed
use. They feature consistent diamond coverage, a strong bond and tight dimensional tolerances. Dumont Diamonds are ideal for laboratory and
other work requiring strict precision and adherence to tight tolerances. 125-180 micron natural diamond (80-100 grit).
BallBallBallBallBallBallBall Shape
A-PD3-1A-PD4-1A-PD24-1A-PD5-1A-PD30-1 A-PD31 A-PD40 Part No.
$12.60$12.60$12.60$12.60$15.75$28.35$29.40 Price Ea
Head Dia. mm
1.01.41.61.82.13.14.0
Head Length/Thick mm
1.01.11.41.61.83.03.9
44.544.544.544.544.544.539.7
Overall Length mm
Standard Plated Diamond
Points 120,000 RPM Max Speed $3.70 Ea
2.35 mm (3/32″) Shank Mounted Plated Points
overall length
Flame Flame Inv. Cone Inv. Cone Shape
Plated Diamond points are for use on hardened steel, glass, precious metals, ceramics,
stone, and composite materials in industrial, jewelry, and laboratory applications, and
A-PD12 A-PD22 A-PD27 A-PD7 Part No.
on hard and soft woods for carving, fine detailing, and texturing. They feature sharp,
Head Dia. mm
1.6 2.62.6 6.0
125-180 micron natural diamond (80-120 grit) that is well balanced for high speed
9.0
8.0
2.0
4.8
Head Length mm
use in micromotor handpieces.
44.5 44.544.5 44.5 Overall Length mm
Ball Ball Ball BallBall BallBallBallCylinder
Cylinder
Cylinder
TaperCone Wheel
Shape
A-PD3 A-PD4 A-PD24 A-PD5A-PD30A-PD25A-PD6A-PD26 A-PD2 A-PD9 A-PD10 A-PD15A-PD11 A-PD20 Part No.
1.0
1.4
1.6
1.8
2.1
2.6
3.3
4.3
1.2 2.3
4.0
2.6
2.1
5.8 Head Dia. mm
.8 1.1 1.4 1.61.6 2.02.73.8 5.0 7.0 8.0 7.010.5 2.0
Head Length mm
44.5 44.5
Overall Length mm
Diamond Hones, Dressing Stone,
Wet Stick Made in USA
Diamond Hones
Dress and reshape mounted abrasive points by lightly touching a rotating
point to the diamond surface. Also for hand smoothing and shaping glass,
metal, stone, bone, and plastic. Use for sharpening chisels & steel instruments. 3/4″ x 2″ diamond pad on 6″ plastic color coded handle.
A-10333 $8.20
Dressing Stone
60 grit Silicon carbide block
allows you to reshape
mounted abrasives back
to perfect concentricity by
running in the groove comparable to head size. Cleans
and exposes fresh abrasive
particles. 3-3/8″ w x 1-1/4″
Wet Stick A-4005 $2.90
Use wet for unloading
plated and sintered diamond points.
2″ x 1/2″ x 3/4″
d x 1/2″ h.
Part Price Diamond No.
EachHone
Grit
A-10342 $9.70 Superfine (blue) 1200 A-10343 $9.70 Fine (red)
600
A-10344 $9.70 Medium (purple) 400
A-10345 $17.85 Coarse (black)
250
6
FOREDOM®
Standard Plated Diamond Chamfer Points
18,000 RPM Max Speed
Priced Below
1/8″ (3.18 mm) Shank Mounted Plated Points
overall length
Plated Diamond Chamfer Points ream out drill holes and leave a smooth and rounded internal surface. They remove sharp edges that can cut
bead string. For use on hardened steel, glass, precious metals, ceramics, stone and composite materials in industrial, jewelry and laboratory applications. Also for use on hard and soft woods for carving fine detailing and texturing.
All Chamfer
Points have
9.0 mm head
lengths and
Overall Length
of 46.0 mm
A-PD51
A-PD52
A-PD53
$7.35 $7.35 $7.35
2.2
120
2.2
220
2.2
400
A-PD55
A-PD56
A-PD57
$7.35 $7.35 $7.35
3.2
120
3.2
220
3.2
400
4.0
120
Plated Diamond Cutting Discs
Unmounted Discs with 1/8″ arbor holes A-DD7 and A-DD9 have plating
on both sides. 120 grit. Use with Mandrels A-M2, A-M20, A-M14, see
page 18.
1/8″ Arbor Holes
A-PD71
A-PD72
A-PD73 $8.40 $8.40$8.40
4.0
220
4.0 400
Part No.
Price Ea
Head Dia. mm
Grit
Using Coolant with Diamond & Ruby Accessories
When drilling or grinding stone, glass, and ceramics with
diamond points you must use a coolant, such as water. Use
Foredom Oil MS10005 when working with metals.
Coolant performs these important functions:
1. It keeps the diamond abrasive particles cool so they don't
heat up and melt the nickel plating or binder which holds
them on the accessory.
A-DD7A-DD9
Part No.
1″2″
Head Dia.″
1/32″1/32″ Thick″
A-M2, A-M20
A-M14
Mandrel
$5.25$10.50
Price Ea
A-M14
A-M2
A-M20
2. It keeps the workpiece cool so that it does not fracture
from the heat.
3. It helps to turn the dust into a safe slurry that cannot
be inhaled.
Premium Ruby Carvers Made in Switzerland. 35,000 RPM Max Speed
Long lasting Fine Grit Ruby Carvers, with ruby crystals firmly bonded to metal frame, provide a smooth finish on hard materials such as steel, porcelain, glass, acrylic, soft and precious metals, and wood. Standard (Coarser) Grit Ruby Carvers provide faster material removal but leave a slightly
rougher finish. These are well suited for woodcarving.
overall length
2.35 mm (3/32″) Shank Ruby Carvers in Fine and Standard Grits Priced Below
Part No.
A-RC15 A-RC19 A-RC20 A-RC11CA-RC13C A-RC14CA-RC15CA-RC16CA-RC32CA-RC34C A-RC36C
$12.10$12.10$12.10 $14.70 $14.70 $14.70 $14.70 $14.70$14.70$14.70 $14.70 Price Ea Fine
Fine
Standard
Standard
Grit
4.53.34.0 8.5 6.5 7.5 7.5 6.55.55.5 5.5
Head Dia. mm
4.5 8.010.016.0 19.0 7.5 12.012.010.010.0 13.0
Head Length mm
44.547.647.6 50.8 54.0 44.5 47.6 47.647.647.6 47.6
Overall Length mm
FOREDOM®
7
3M Flexible Diamond Sanding
x 1/2″
Bands and Discs Made in USA 1/2″
band
Flexible Diamond bands and discs
are made from a two-ply polyester
backing film evenly coated with
diamond filled nickel plated dots.
Use wet with water when working
on glass or stone, and oil when
working on metals. Clean and
unload with the A-AC1 Abrasive
Cleaner or A-HB58 Brass Brush
on pg 23. Bands in several grits
come in 1/4″ and 1/2″ (6 & 13 mm)
diameters for use with rubber drum
mandrels with 3/32″ (2.35 mm),
1/8″, and 1/4″ shanks.
2″ discs (51 mm) with PSA backs
come in several grits for use on
2″ disc mandrels in flex shaft
handpieces, BL Bench Lathe and
Foredom’s Angle Grinder. See pages
18-20 for complete mandrel listing.
Use Flexible Diamond Bands and Discs to Grind, Sand, & Smooth
on various materials: Glass, Carbide, Composite, Plastic, Enamels, Stone,
Steel, Exotic Alloys, Gypsum, Ceramics, Wood, Bone, Chrome Cobalt,
Painted or Plated Surfaces, Fiberglass
Bands– Flexible Diamond Priced Ea
Micron
Grade
Grit Individual Part No. Price
Each
Mandrels
Max Speed
1/4″ D x 1/2″ L (6 x 13mm)
250
60
A-4812 $10.40
For use in Handpieces:
125
120
A-48138.90
A-SD324
74220 A-4814
8.90
40,000 RPM
A-SD184
40400 A-4817
8.90
20800 A-4818
8.90 5-Pc Assortment AK4810 $43.00 (1 ea of 5 grits) 1/2″ D x 1/2″ L (13 x 13mm)
2″ PSA Discs
3M Cerium Oxide Sanding
Bands and Discs
Cerium Oxide Abrasives are used
for achieving a final, high shine
polish on gemstone, rock and
glass. Bands and discs must be
used wet. Results are also best
when used following a 1,200 to
4,000 grit abrasive.
Bands– Cerium Oxide Priced Ea
Grit/Micron
Grade
Individual Part No. Price
Each
Mandrels
Max Speed
25060A-4822 $13.10
125120 A-4823
12.00
74220 A-4824
10.80
A-SD328
40400 A-4827
10.00
A-SD188 40,000 RPM
20800 A-4828 10.00
5-Pc Assortment AK4820 $52.50 (1 ea of 5 grits) 50,000/.5
Discs– Flexible Diamond Priced Ea
Discs– Cerium Oxide Priced Ea
Micron
Grade
Each
Mandrels
Max Speed
2″ (51mm) PSA
25060A-5752 $17.30
A-M33, A-M335
125120 A-5753
13.90
A-M338 10,000 RPM
74220 A-5754
11.80
For use on Angle Grinder:
40400 A-5756
9.70
A-69222 with A-10041
20800 A-5758
9.70
5-Pc Assortment AK5750 $57.75 (1 ea
of 5 grits) 1/4″ D x 1/2″ L (6 x 13mm)
50,000/.5
A-4402
$2.00
1/2″ D x 1/2″ L (13 x 13mm)
A-4404
$2.60
3/4″ (19mm) PSA
50,000/.5
A-4406
$1.30
2″ (51mm) PSA
50,000/.5
A-4408
$5.90
See pages 18-20 for complete
mandrel listing.
A-SD324
40,000 RPM
A-SD184
A-SD328
40,000 RPM
A-SD188
A-M4 15,000 RPM
A-M33, 10,000 RPM
A-M335,
A-M338
For use on Angle Grinder:
See Note Below:
Use 2″ Flexible Diamond, Cerium Oxide, Diamond Microfinishing, Ceramic Purple and Trizact Discs on Flex Shaft Handpieces,
Angle Grinder Attachment, and BL Bench Lathe:
Handpieces: Mount with 2″ Disc Mandrels and Velcro® Hook and Loop Discs, see page 20.
Angle Grinder: Mount with Velcro® Hook Disc Mandrel & Velcro® Loop Disc, see page 31.
Bench Lathe: Mount with 2″ and 3″ Disc Mandrels and Velcro® Hook & Loop Discs, see pages 20 & 31. A-CHA-5 Collet Holder is also needed.
See our Power Tool Catalog or www.foredom.net for BL Lathe Components and Accessories.
8
FOREDOM®
3M Film Sanding Bands
and PSA Discs Made in USA
Diamond Microfinishing
Bands and Discs
Diamond Microfinishing abrasives have flexible film backing suitable for metal working and lapidary applications. They work great on
all materials including stone, glass, stainless steel and titanium. Use
wet with water when working with gemstone, rock and glass, and oil
when working on metals. Bands in several grits come in 1/4″ and 1/2″
(6, 13mm) diameters for use with rubber drum mandrels with 3/32″
(2.35mm) & 1/8″ shanks. Discs in 3/4″ and 2″ (19 & 51mm) with
PSA backs come in several grits for use on disc mandrels in Flex Shaft
Handpieces, BL Bench Lathe and Foredom’s Angle Grinder. See bottom
of page 8 and pages 18-20 for complete mandrel listing.
Bands– Diamond Microfinishing Priced Ea
Discs– Diamond Microfinishing Priced Ea
Micron
Grade
Micron
Grade
Each
Mandrels Max Speed
1/4″ D x 1/2″ L (6 x 13mm)
125
120
74220
45320
30400
20800
9 1,200
A-4412
$4.90
A-4413 4.50
A-4414
4.00
A-4415 3.25
A-4416 3.25
A-4417 3.25 1/2″ D x 1/2″ L (13 x 13mm)
125
120
74220
45320
30400
20800
9 1,200
A-SD324
40,000 RPM
A-SD184
A-4422
$6.20
A-4423 5.70
A-4424
5.10
A-4425 4.40
A-4426 4.00
A-4427 4.00
A-SD328
40,000 RPM
A-SD188
Grit Individual Part No. 2″
PSA
(51mm)
Price
Each
Mandrels
Max Speed
A-M33, 10,000 RPM
A-M335
A-M338
For use in Angle Grinder:
See pgs 31 & 32
125
120
A-4452
$4.70
74220 A-4453 4.60
45320 A-4454
4.60
30400 A-4455 4.60
20800 A-4456
4.60
91,200 A-4457 4.60
3 4,000
A-4583 8.20
7-Pc Assortment of 2″ Discs AK4450 (1 of ea grit) $33.60
16-Pc Assortment of 2″ Discs AK4400 (1 of ea grit plus 8 A-10041
Velcro Loop Discs and One A-10040 Velcro Hook Disc) $47.25
3M Wet/Dry Micron Graded Polishing Papers
Polishing paper is a soft cloth-like material with aluminum oxide grain
for use on any contoured surface with or without water. Working in
sequence from coarse to the finest sheet brings the best results. 8-1⁄2″
x 11″ sheets come in six micron grades in packs of 10 per grit. Papers
can be cut lengthwise into 1-1⁄2″, 1″, 3/4″ or 1/2″ wide strips, taped,
and made into rolls for use on Finger Sanders and Sanding Sticks.
Papers can also be cut into much smaller pieces, wrapped and glued for
use on split mandrels, see page 18.
10-Pks of 8-1/2″ x 11″
Sheets $22.70
Made in USA
Micron
Grade Grit/Color
Abrasive 10-Pk Part No. Price/
10-Pk
1 10,000/White
Aluminum Oxide 37-941
2 6,000/Aqua
3 4,000/Pink
9 1,200/Lt. Blue
15 800/Gray
Silicon Carbide 37-945
30400/Green
Silicon Carbide
$22.70
37-946
6-Pc Assortment 8-1/2″ x-11″ Sheets (1 each grade) 37-948 $13.40
Super Bond Film Tape 1″ x 36 Yards 37-959 Use for making belts for hand sanders
FOREDOM®
$13.65
9
3″ PSA disc
on A-M34
disc mandrel
3M Ceramic Purple Sanding
Bands and Discs Made in USA
Ceramic Purple Abrasives are excellent for sanding and finishing wood, metals,
fiberglass, diestone, plastics, and other materials. 3M’s CubitronTM ceramic
aluminum oxide mineral sharpens itself with use. Once initial grinding wears
the grain flat, it fractures along micro cracks creating new cutting edges. This
process repeats itself throughout the entire grinding process.
• 2 to 4 times longer abrasive life than aluminum oxide bands and discs
• Faster stock removal with less heat and loading
• Available in 60, 80, 120, 220 grit
• Use Bands with 3/32″ (2.35 mm), 1/8″, & 1/4″ shank rubber drum mandrels.
• Use 2″ & 3″ (51 & 76 mm) diameter PSA Sanding Discs (pressure sensitive
adhesive) on disc mandrels, see Mandrels on pages 19-20.
2″ Discs also for use with Angle Grinder, see page 31.
3″ Discs should be used on BL Lathe and not flexible shaft handpieces.
Optimum Operating Speeds are between 25%–50% of max listed speed for
each size band or disc.
3/4″ x 1-1/2″
bands
1/2″ x
1/2″ bands
1/4″ x 1/2″
bands
2″
PSA
disc
Bands– Ceramic Purple Priced Per 10-Pk
Discs– Ceramic Purple PSA Priced Below
Grit 2″ (51 mm) Priced Ea
3″ (76 mm) Priced Ea
Grit
Grit
10-Pk Part No.
Price per 10-Pk Mandrels
Max Speed
1/4″ D x 1/2″ L (6 x 13mm)
60
A-4912-10
$3.90
A-SD324
80
A-4913-10
40,000 RPM
A-SD184
120
A-4914-10
220
A-4916-10
12-Pc Assort. AK4910$4.60 (3 ea of 4 grits)
1/2″ D x 1/2″ L (13 x 13mm)
60
80
120
220
12-Pc Assort.
A-SD328
A-4922-10
$5.35
40,000 RPM
A-SD188
A-4923-10
A-4924-10
A-4926-10
AK4920$6.30 (3 ea of 4 grits)
3/4″ D x 1-1/2″ L (19 x 38mm)
60
80
120
220
12-Pc Assort.
A-4942-10 $16.80
A-SD145
A-4943-10
A-4944-10
A-4946-10
AK4940$19.95 (3 ea of 4 grits)
10,000 RPM
3M Trizact Sanding Bands
and Discs Made in USA
TM
Use in Handpieces with mandrels:
A-M33, A-M335, A-M338 10,000 RPM
Max Speed. Also use on Angle Grinder
See page 31.
Part No.
Price Ea
60 A-5682 $1.30
80 A-5683 120 A-5684 220 A-5685
4-Pc Assort. AK5680
$4.70 (1 ea of 4 grits) Price Ea
Use 2″ Ceramic Purple, Trizact , Aluminum Oxide, Flexible Diamond,
Cerium Oxide, Diamond Microfinishing Discs on Flex Shaft
Handpieces, Angle Grinder Attachment, and BL Bench Lathe.
3″ Discs should be used on BL Lathe:
Handpieces: Mount with 2″ Disc Mandrels and Velcro® Hook & Loop Discs,
see page 20.
Angle Grinder: Mount with Velcro® Hook Disc Mandrel & Velcro® Loop Disc,
see page 31.
Bench Lathe: Mount with 2″ and 3″ Disc Mandrels and Velcro® Hook &
Loop Discs, see pages 20 and 33. A-CHA-5 Collet Holder is also needed.
See our Power Tool Catalog or www.foredom.net for more info
Use Trizact bands and discs wet or dry for finishing and pre-polishing
on all metals, plastics and composites. Trizact's innovative 'microreplication technology' ensures a fast and consistent cutting rate
with uniform finishes.
3″ Discs – Priced Each
Use with A-M34 Disc Mandrel and
A-CHA-5 Collet Holder on BL Bench
Lathe, 10,000 RPM Max Speed
Use in Handpieces with mandrel:
A-SD141, 20,000 RPM Max Speed
Grit 10-Pk Part No.
Price/10-Pk
220 A-4733-10 $8.40
400 A-4735-10
600 A-4736-10
1,200 A-4737-10
2,500 A-4738-10
15-Pc Assort. AK4730
$11.55 (3 ea of 5 grits)
10
Part No.
60 A-5692 $3.00
80 A-5693 120 A-5694 220 A-5695
4-Pc Assort. AK5690
$11.00 (1 ea of 4 grits) Bands– 1/2″ D x 1″ L (13
x 25 mm) Priced/10-Pk
See Wayne Werner
AK3375 Assortment
Kit, pg. 20
Use with A-M34 Disc Mandrel and
A-CHA-5 Collet Holder on BL Bench
Lathe, 10,000 RPM Max Speed
See page 20.
FOREDOM®
Grit Part No.
Price Ea
220 A-5942 $1.80
400 A-5943 600 A-5944 1,200 A-5946
2,500A-5948
4-Pc Assort. AK5940
$8.70 (1 ea of 4 grits) FOREDOM ELECTRIC CO.
3M Aluminum Oxide Sanding
Bands and Discs Made in USA
Aluminum oxide sanding bands and discs are made of high-
grade mineral and a bonding system which reduces shelling of the mineral. These economical abrasives are excellent for fast clean up and pre-polishing work.
• Available in 60, 80, 120, 220 grit
• Use Sanding Bands with 3/32″ (2.35mm), 1/8″, and 1/4″ shank
rubber drum mandrels.
• Use 2″ PSA Sanding Discs (pressure sensitive adhesive) on disc
mandrels in handpieces. Also for use with Angle Grinder, see page 31.
See Mandrels on pages 19-20.
1/2″ x 1/2″
bands
2″ PSA disc
3/4″ x
1-1/2″ band
Bands– Aluminum Oxide Priced Per 10-Pk
Discs– 2″ Aluminum Oxide PSA Priced Per 10-Pk
Grit Grit 10-Pk Part No.
Price per 10-Pk Mandrels Max Speed
1/4″ D x 1/2″ L (6 x 13mm)
A-SD324 40,000 RPM
60
A-4612-10 $2.10
A-SD184
80
A-4613-10 120
A-4614-10
220
A-4616-10
12-Pc Assort. AK4610 $2.50 (3 ea of 4 grits)
A-SD328 40,000 RPM
1/2″ D x 1/2″ L (13 x 13mm)
A-SD188
60
A-4622-10 $2.80
80
A-4623-10 120
A-4624-10
220
A-4626-10
A-SD326 40,000 RPM
3/8″ D x 1/2″ L (9.5 x 13mm)
A-SD186
60
A-4642-10 $2.10
80
A-4643-10 120
A-4644-10
220
A-4646-10
3/4″ D x 1-1/2″ L (19 x 38mm)
A-SD145 10,000 RPM
60
A-4662-10 $7.35
80
A-4663-10 120
A-4664-10
220
A-4666-10
10-Pk Part No.
Price per 10-Pk 60
A-5632-10 $8.40
80
A-5633-10 120
A-5634-10
220
A-5635-10
8-Pc Assort. AK5630 $6.80
(2 ea of 4 grits)
Mandrels Max Speed
A-M33 10,000 RPM
A-M335, A-M338
Use with Angle Grinder,
see pg 31
Part Numbers and Prices are shown in red
on each page.
Aluminum Oxide Sanding
Flap Wheels Made in USA
3/4″ Dia., 1/8″ Shanks $8.50 Ea
Made from economical aluminum oxide mineral. 3/4″ wheels come
mounted on 1/8″ shanks in coarse (60), medium (80), & fine (120) grits.
3/16″ Thick
3/8″ Thick
Coarse
A-FW-1C
Medium A-FW-1M
Fine A-FW-1F
Coarse
Medium
Fine
A-FW-2C
A-FW-2M
A-FW-2F
Replacement Sandpaper Belts for Foredom Belt Sander
5,000 RPM Maximum Speed, 500–4,000 RPM Optimum Speed
See our Power Tool Catalog or www.foredom.net
for more information of the Belt Sander
257mm Long Replacement Sandpaper Belts come in 7mm & 10mm widths
Assortments
Assortments Grit 7mm Belts*
10mm Belts 7mm Belts
10mm Belts
$3.70/5-Pk
$4.70/5-Pk Coarse 3 ea 100, 180, 240 grit
100 A-797415A-797515
AK797409 $5.25/9-Pk
AK797509 $6.80/9-Pk
180 A-797425 A-797525 Fine
3 ea 320, 600, 1000 grit 240 A-797435A-797535 AK797429 $5.25/9-Pk
AK797529 $6.80/9-Pk
320
A-797445A-797545 Coarse 3 ea 100, 180, 240, 320, 600 & 1000 grit 600
A-797455A-797555 & Fine AK797439 $10.50/18-Pk AK797539 $13.60/18-Pk
1,000
A-797465A-797565 * 7mm Belts came installed on Older Models of Belt Sanders with Serial #'s from H11XXXXX to H09XXXXX
FOREDOM®
11
CW Polishing Wheels $12.00/10-Pk
Foredom’s top of the line CW Ceramic Impregnated Polishing Wheels come
in 6 different grits for smoothing and polishing precious metals including
platinum, gold, silver, titanium, chrome cobalt, and all hard alloys. CW wheels
are non-contaminating and work faster and last longer than other polishers.
10-Pk Part No.
Jewelry Designs of Danbury,
CT uses CW Wheels to
polish flats on gold bangle
bracelet.
Specifications:
7/8″ Dia. x 1/8″ Thick
(22 x 3.2mm)
1/16″ Center Holes
Color
Description
A-M1
A-M6
1/16″1/16″
arborarbor
holehole
Grit
A-CW55810
White
Super Fine
1,500
A-CW55710
Gray
Extra Fine 1,000
A-CW55610
Orange
Fine
500
A-CW55410
Violet
Medium
320
A-CW55210
Green
Med/Coarse
180 A-CW55110
Blue
Coarse
120 A-CW55010 Assortment with 2 ea. Blue, Green, Violet, Orange and 1 ea. Gray and White.
Mandrels
3/32″ & 1/8″
Shanks
Use A-M1 & A-M6 to
mount CW, Rubber
Bonded and small
wheels with 1/16″
arbor holes. See
Mandrels on page 18.
Rubber Bonded Abrasive Wheels $6.60/10-Pk
Rubber Bonded Abrasive (silicon carbide) Unmounted Wheels are used for light deburring, cleaning,
smoothing and polishing. Ideal for hard-to-reach areas on ferrous and non-ferrous alloys and other
materials. Offers cushioned action performance. Available in Coarse, Medium and Fine. Color coded by
grit. Sold in packs of 10. Wheels have 1/16″ Center Holes and should be used with A-M1 & A-M6
Mandrels.
10-Pk Part No.
Dia. Thick Color
Description Grit
A-A1
A-A1F-107/8″1/8″
Dark Green Fine
180
A-A1M-107/8″1/8″Black Medium 80-120
A-A1C-107/8″1/8″Brown Coarse 40-60
A-A2
A-A2F-105/8″3/32″ Dark Green Fine
180
A-A2M-105/8″3/32″Black
Medium 80-120
A-A2C-105/8″3/32″Brown Coarse
40-60
A-A3
A-A3F-105/8″1/8″
Dark Green Fine
180
A-A3M-105/8″1/8″Black Medium 80-120
A-A3C-105/8″1/8″Brown Coarse 40-60
AK122 $31.50 56-Pc Kit
6 each of A-A1, A-A2 and A-A3 in all
3 grits. Also A-M1 and A-M6 mandrels.
A-M19
Abrasive Discs and Cut Off Wheels Made in USA
A-M13A-M14
1/16″ 1/8″
arbor arbor
holehole
Rubber Bonded Discs A-D1 and A-D2 are suitable for grinding, smoothing,
and cleaning glass, high speed steel, and other tough materials. Discs have
1/16″ (1.6mm) arbor holes.
Fiberglass Reinforced Cut-Off Wheels A-D6, A-D8, A-D9 and A-D11are used
to cut-off, groove, and trim metal, wood, and ceramics. A-D11 is also for use
with Foredom’s Angle Grinder Attachment for the H.30 Handpiece.
A-D1-5
A-D2-5
A-D6
A-D8
A-D9
1/8″ Shank
A-D11
Part No.
Dia
Thick
Grit
Arbor Hole Max Speed
Price
A-D1-57/8″.023″90 1/16″
30,000 RPM
$ 1.25/ 5-Pk A-D2-51-1⁄4″.062″90 1/16″
30,000 RPM 2.30/ 5-Pk
A-D61-1⁄4″.050″60 1/16″
40,000 RPM 1.50 Ea
A-D81-1⁄2″.050″60 1/8″
40,000 RPM 1.60 Ea
A-D92″.050″60 1/8″
40,000 RPM 1.70 Ea
A-D11
2″.047″60 3/8″
30,000 RPM 1.90 Ea
12
Mandrels
Fiberglass Cut Off Wheels
Rubber Bonded Discs
FOREDOM®
1/16″ arbor hole
Use A-M1, A-M6,
A-M13 and A-M19
to mount Discs and
Wheels up to 1-1/4″
dia. with 1/16″ arbor
holes. Use A-M14 to
mount wheels up to
1-1/2″ with 1/8″ arbor
holes. See page 18.
Recommended Mandrels
A-M1 or A-M6 for use in Handpiece
A-M14 for use in Handpiece
A-M14 for use in Handpiece
A-M31 for use in Handpiece or
A-69212 Short Hub in Angle Grinder
Brushes– Mounted and Unmounted
Cup, Wheel & End Shaped Mounted Brushes for use
in Handpieces 25,000 RPM Max Speed
AK70 $26.20 14-Pc Kit
Mounted Steel Brushes Priced Below
Steel Brushes are suitable for use on all metal surfaces for removing
rust and corrosion, deburring, cleaning, edge blending, and other
surface texturing and preparation. Made with .003″ and .005″ wire.
Head Trim
Overall Wire ShapeDia Length Length Size
2 each of A-MB1, A-MB2,
A-MB3, A-MB4, A-MB5,
A-MB6 and A-MB7
3/32″
Shanks
Mounted Bristle Brushes Priced Below
1/8″ Shanks
end3/16″ 1/4″1-7/8″ .003″
wheel3/4″ 3/16″ 1-5/8″ .003″
wheel3/4″ 3/16″ 1-5/8″.005″
Bristle Brushes are used to clean and prepare surfaces for buffing and
polishing. They are made with natural animal hair–horsehair for stiff
and goat hair for soft bristles. Bristles are securely held in steel rings,
evenly distributed and trimmed. The wheel, cup and end shapes will
work on flat, curved, hard-to-reach surfaces.
Head Trim
ShapeDia Length 3/32″
Shanks
cup9/16″ wheel9/16″ wheel3/4″ end3/16″ end1/4″ Overall Part
Length HardnessNo.
5/32″2″ Stiff
1/8″ 1-5/8″Stiff
3/16″ 1-5/8″Stiff
1/4″1-7/8″Stiff
3/8″ 2-1/8″Stiff
1/8″
Shanks
cup9/16″ 1/4″ 2″ Stiff
wheel3/4″ 3/16″1-5/8″ Stiff
wheel3/4″ 3/16″ 1-5/8″ Soft
Price
Each
A-MB1$1.90
A-MB251.30
A-MB21.70
A-MB31.70
A-MB353.10
A-MB18$1.70
A-MB281.70
A-MB2381.90
Mounted Brass Brushes Priced Below
Brass Brushes are suitable for use on all metal surfaces for removing
rust and corrosion, deburring, cleaning, edge blending, and other
surface texturing and preparation. Made with .003″ and .005″ wire.
Head Trim
Overall Wire ShapeDia Length Length Size
3/32″
Shanks
end1/8″ wheel3/4″ Part
No.
Price
Each
1/4″
3/16″ 1-7/8″ .003″
1-5/8″ .005″
A-MB4$2.00
A-MB62.50
5/16″ 1-5/8″.005″
A-MB68$3.20
1/8″ Shank
wheel1″ Made in USA
1″ Muslin Wheel, Satin Finishers
3/32″ (2.35mm)
Shank $2.40 Ea
2″.005″
1-7/8″ .003″
2-3/8″ .005″
1-5/8″ .003″
1-5/8″ .005″
1-5/8″ .003″
Part No.
Type
Style/Grit
Thickness
A-5520A-5523A-5517A-5524
Muslin Satin Finisher Satin Finisher Satin Finisher
Loose
Extra Fine
Fine
Coarse
1/4″1/4″5/16″3/8″
Price
Each
A-MB5$2.00
A-MB733.10
A-MB72.50
A-MB128$3.40
A-MB584.00
A-MB5385.50
A-MB7385.40
A-MB783.70
A-MB8383.70
Unmounted Nylon
and Wire Brushes for
use in Handpieces &
BL Bench Lathe
A-W301A-W302
Soft nylon Brush A-W301 is great at very low speeds for cleaning up
“fuzzies” left behind on delicate carvings without removing fine detail. Can be used with a mandrel on a handpiece or mounted directly
onto tapered spindle of the BL Lathe. A-W302 steel wire brush is used
for texturing, removing rust and corrosion, edge blending and polishing of cast or machined metal surfaces or hard-to-reach areas. Used
with mandrels in flex shaft handpieces (see page 18) or A-WM-5,
A-WM-6 Wheel Mandrels on the BL Bench Lathe (see page 33).
Part
No.Dia Material Wire Hole Use with
Size Size Mandrel
A-W3012″
Soft Nylon
N/A 3/16″ A-M78 & A-M89$7.20
Price
Each
A-W3022″
Steel Wire
.008″ 1/4″ A-M8, A-M85 $11.55
or Tapered Spindles of Lathe
Unitized Mounted Points
3/32″ (2.35mm) Shank $6.50 Ea
Made of pressed, non-woven, tough
abrasive nylon fibers with aluminum oxide grain, these accessories come in different shapes and grits. Use for surface
blending, preparation and finishing. Also
light deburring. Long lasting, smooth
running and non-contaminating.
1-3/4″ overall
length
Muslin Buff provides a variety of finishes and requires compound
(see page 16). Extra fine, fine and coarse Satin Finishers have nylon
heads impregnated with abrasive grit. Use to clean and obtain matte
finishes on metal or plastic surfaces.
cup5/8″1/4″ end3/16″ 1/4″ end5/16″ 9/16″ wheel3/4″ 3/16″ wheel3/4″3/16″ wheel1″ 5/16″
Part
No.
Part No. Shape Grit
A-5591 Ball NoseFine
A-5592 Ball NoseMed
A-5593 Ball NoseCoarse
A-5594 Flat Taper Fine
A-5595 Flat TaperMed
A-5596 Flat TaperCoarse
A-5597 Wheel Fine
A-5598Wheel Med
A-5599Wheel Coarse
Fine grit: requires very light
pressure, conformable
Medium grit: requires heavy
pressure, aggressive
Coarse grit: requires heaviest pressure, most aggressive
Ball Nose Flat Top Taper Wheel
Shape
1/2″ x 1/2″ 3/8″ x 3/4″ 3/4″ x 1/4″ Size
1-7/8″
2-1/8″
1-3/4″
Overall Length
FOREDOM®
13
3M
Radial Bristle Discs– 9/16″, 3/4″, 1″
9/16″ Diameter with 1/16″ arbor hole
6-Pk $10.40
1″ Diameter with 1/8″ arbor hole
6-Pk $13.10
120 grit/white
A-4522-6
36 grit/brown
A-4532-6
220 grit/red
A-4523-6 400 grit/blue
A-4524-6 30,000 RPM Max Speed
Recommended Operating
Speed for most applications is
3,000– 18,000 RPM.
5,000 RPM for Woodcarving.
Slower speeds allow greater flexibility and a softer touch with the
bristles. Use the tips of the bristles
with light pressure to extend the
life of the accessory and achieve
more subtle results. Higher
speeds provide more aggressive
material removal.
50 grit/green
A-4533-6 Pumice (1,200 grit) pink
A-4526-6 6 micron (3,000 grit) peach
A-4527-6 80 grit/yellow
A-4534-6 1 micron (14,000 grit) light green
A-4528-6
120 grit/white
A-4535-6
3/4″ Diameter with 1/16″ arbor hole
6-Pk $10.40
Made in USA
80 grit/yellow
A-4511-6
120 grit/white
A-4512-6
220 grit/red
A-4513-6 400 grit/blue
A-4514-6 Pumice (1,200 grit) pink
A-4516-6 6 micron (3,000 grit) peach
A-4517-6 Stack 6 or more discs onto a
mandrel for making a sturdy
brush. Discs are not used individually except when working
in the narrowest of channels.
Mandrels for use with Radial Bristle Discs
See page 18 for description of Mandrels
Part No.
Shank
Arbor 9/16″ 3/4″
A-M1
3/32″ 1/16″
k
A-M2 3/32″ 1/8″
A-M6
1/8″1/16″
A-M20 1/8″1/8″
A-M14
1/8″1/8″
A-M15 1/8″1/16″
k
k
k
k
k
Assortment Kits
with Mandrels Part No.
1″
k
k
k
Price
$61.95
9/16″ 37-pc kit
AK4520
3/4″ 38-pc kit
AK4510
$63 3/4″ 26-pc kit
AK4515
$39.90 3/4″ 10-pc kit AK4519
$14.70 6 discs ea. of 120, 220, 400, Pumice, 6 micron, & 1 micron
plus A-M1 mandrel (3/32″)
6 discs ea. of 80, 220, 400, Pumice, 6 micron, and 1 micron plus A-M1 (3/32″) and A-M6 (1/8″) mandrels
6 discs ea. of 80, 120, 220, 400, and plus A-M1 (3/32″) and
A-M6 (1/8″) mandrels
3 discs ea. of 80, 400, & 6 micron + A-M6 (1/8″) mandrel
1″ 25-pc kit
1 micron (14,000 grit) light green
A-4518-6
AK4530
1″ 10-pc kit
$51.50
AK4539
$19.95 3 discs ea. of 36, 80, and 120 grit + A-M20 (1/8″) mandrel
14
6 discs ea. of 36, 50, 80, & 120 grit + A-M20 (1/8″) mandrel
FOREDOM®
Scotch-Brite Radial Bristle Discs
have thin flexible bristles that get
into hard to reach areas without
removing detail or making flat
spots. No need to add compound.
3M Cubitron™ and aluminum
oxide grain embedded throughout
the bristles enable them to work
faster and last far longer than
rubber wheels, regular brushes,
buffs or conventional sanders.
They generate little or no dust nor
the heat associated with wheels
and buffs.
For Dental Labs & Jewelers
These non-contaminating discs
are ideal for cleaning metal
surfaces, removing light fire scale
and oxide, finishing, blending, texturing, pre-polishing and polishing
all precious and non-precious
metals, dental acrylics, flexite, and
ceramics.
For Woodcarvers Scotch-Brite
Radial Bristle Discs are superior
to sandpaper, flap wheels, or
other types of sanders, brushes
or abrasive wheels for many
woodcarving and woodworking
applications. Their flexible bristles
can sand areas with detail, irregular, curved, or flat surfaces on
soft or hard woods. Carvers can
remove the “fuzzies” left behind
without harming any of the
underlying detail. The coarser grits
can be used to carve and texture,
while the finer grits will smooth,
burnish, and polish.
3M
Radial Bristle Discs– 2″ & 3″
with 3/8” arbor hole. Made in USA
2″ Dia
6-Pk
Recommended Speed for most applications is 3,000–
18,000 RPM
$22.90 3″ Dia
6-Pk
3″ Discs 20,000 RPM Max Operating Speed
80 grit/yellow
A-4542-6
80 grit/yellow
A-4552-6
2″ Discs 30,000 RPM Max Operating Speed
Recommended Speed for most applications is 2,000–
18,000 RPM
2″ and 3″ Scotch-Brite Radial Bristle Discs share the same
excellent properties as the smaller sizes shown on the
opposite page. These larger discs can be stacked on mandrels for use with flex shaft and micromotor handpieces,
and on spindle adapters for use on the BL bench lathe. 2″
discs can also be used with our short and long mounting
hubs on Foredom’s Angle Grinder Attachment. See mandrels listing below. When using on the lathe, Radial Bristle
Discs are most effective at speeds of 2,000 to 7,000 RPM.
$31.20
120 grit/white
A-4543-6
120 grit/white
A-4553-6
220 grit/red
A-4544-6
220 grit/red
A-4554-6
400 grit/blue
A-4545-6
400 grit/blue
A-4555-6
Pumice
1,200 grit/pink
A-4546-6
6 Micron
3,000 grit/
peach
A-4547-6
Mandrels for use with 2″ and 3″ Radial
Bristle Discs. See page 18 for description of Mandrels and
Spindle Adapters
Part No.
Arbor Hole/
Shank Size
For Use with Handpieces:
A-M30 Flat Head 1/4″
A-M31 Screw 1/4″
For Use with Bench Lathe:
A-4561 Right Side3/8″
Black
Tapered Spindle Adapter
A-4562 Left Side3/8″
Grey
Tapered Spindle Adapter
For Use with Angle Grinder:
A-69212 Short Hub
A-69212L Long Hub
2″ 3″
k
k
k
k
k
k
k
k
Pumice
1,200 grit/pink
A-4556-6
1 Micron
14,000 grit/
light green
A-4548-6
6 Micron
3,000 grit/
peach
A-4557-6
1 Micron
14,000 grit/
light green
A-4558-6
k
k
FOREDOM®
15
Felt Buffing and Polishing Accessories
Felt Buffing and Polishing Accessories are used with compounds on hard and soft metals, metal plate, precious metals, plastics, wood, acrylic, and painted surfaces. Select the
appropriate compound, below, for the material being worked to produce desired finish.
AKFK3 $39.90
16-Pc Kit
Mounted Felt Bobs
* Please specify
Medium or Hard
Density when ordering individual
Felt Bobs by adding M or H to Part
No., i.e. A-MS1H
1/8″ shanks
Contains all 8 shapes below
in medium and hard densities
overall length
1/8″ (3.18mm) Shank Mounted Felt Bobs Priced Ea
More About Felt:
Felt is a compound carrier and the abrasives
in compounds perform the actual polishing
function. However, surface speed, felt hardness, applied pressure, and frictional contact
determine the amount of surface removal,
or polishing desired. “Cutting down” refers
to a greater amount of surface removal than
does “coloring”. Whether someone uses
the term buffing, polishing or finishing, they
typically mean a 2-step process of cutting
and then coloring by which the luster or
reflectiveness of a product is enhanced.
-MS1* A-MS3* A-MS4* A-MS6* A-MP1* A-MP4* A-MP5* A-MP8*Part No. A
$3.00 $3.00$3.00 $3.00$1.60 $1.70 $1.90 $3.00 Price
1/2″1/2″1/2″1/2″1/4″3/8″1/2″3/4″ Dia.
1″1″3/4″1/2″1/4″1/2″1/2″3/4″ Length/Thick
2-5/16″2-5/16″2-5/16″2-1/8″1-7/8″1-7/8″2-1/16″2-1/4″ Overall Length
4
5
6
Polishing Compounds
7
Made in USA
AK4000 4 Bar Kit – Includes A-4001
Emery, A-4002 Tripoli, A-4003 White
Diamond, A-4004 Red Rouge
Kit
22.25 oz. AK4000$11.10
Emery
6.5 oz. bar A-4001$2.80
19 oz. bar A-50019.20
Tripoli
4.5 oz. bar A-4002$2.80 14 oz. bar A-50029.20
White Diamond Rouge
5.5 oz. bar A-4003$2.80
Red Rouge
5.75 oz. bar A-4004$2.80
17 oz. bar A-50049.20
1 oz. tube A-400412.10
Platinum Blue
5 oz. bar
A-4007$6.50
Platinum White
5.75 oz. barA-4006 $9.20 1 oz. tube A-400612.50
Carnauba 2 oz. bar
A-4008$9.20
1
2
Our polishing compounds come in standard size bars.
Platinum White and Red Rouge also come in small tubes that are
sized and priced right for getting started with a new compound. Platinum
White is a unique formulation that is only available from Foredom.
1 Emery (Black) Contains coarse grit to remove surface
imperfections, scratches, rust, and burrs from
iron, steel and other hard metals.
2 Tripoli (Brown) Most popular compound for blending and
contouring. Also for general cutting down,
scratch removal, and buffing on acrylics and
non-ferrous metals such as zinc die castings,
brass, copper, aluminum castings and sheets.
3 White Diamond Rouge Fast cutting on hard metals. Made with fine
abrasive powder that produces a final satin
finish on chrome, stainless steel, carbon steel,
brass, and aluminum. Also use to remove rust,
scale and carbon deposits on metal surfaces.
4 Red Rouge
Produces a high luster on gold, silver, pewter,
nickel plating and plastics for final polishing.
16
3
FOREDOM®
5 Platinum Blue For pre-polishing & cutting down of platinum
and other metals.
6 Platinum White Use for final polishing.
Produces a deep luster
high color final polish
on platinum, gold,
silver, and all metals.
Also for final polishing on flexible partial
material and acrylic.
7 Carnauba The hardest natural wax available. Non-tacky
and highly regarded for its tough and wear
resistant qualities. It is especially good for
producing a high luster on wood and
painted surfaces.
Cotton and Felt Polishing Buffs
Made in USA
Use 1″ and 2″ Buffs with A-M78 & A-M89 Mandrels at 20,000 RPM Max Speed. 2″ Goblet and
3″ and larger Buffs are for use on Bench Lathe tapered spindels at 5,000 RPM Max Speed
White Muslin Buffs
Loose White Muslin Buffs
These buffs have only one row of stitching
around the arbor hole which is reinforced with
leather and shellac (L/S). Made of Finex (80
x 80 weave) muslin with combed edges. The
open layers provide a softer polishing action
and conform to contours and curves. Use with
rouge for coloring or final polishing operations.
Coarse Weave (60 x 60) Muslin
has a more open weave to hold more compound. Used as a general purpose buff with
cutting and polishing compounds. Combed
edges do not need breaking in or combing to
hold compound. The center pin holes are reinforced with shellac (S) for a tight fit on tapered
mandrels and greater durability.
Rows of Center
Dia.PlyStitching Hole
Part
No.
Price Each
1″40 1
S A-CBC1$2.40
2″40 1
S A-CBC22.60
3″40 3
S A-CBC33.70
4″40 3
S A-CBC44.80
6″50 4
S* A-CBC658.90
Dia.
Ply
Part No.
3″
A-LCB35$3.70
35 Price
Each
3″40 A-LCB34.10
4″40 A-LCB45.40
Yellow Treated Cotton Buffs
Rows of Center
Rows of Center
Part
No.
Price Each
1″40 1
S A-CBF1$2.60
4″30 3
S A-CBY43$6.25
2″40 1
S A-CBF22.90
4″40 3
S A-CBY47.35
S A-CBF34.10
5″40 3
L/S A-CBY58.70
S A-CBF45.25
6″40 4
L/S A-CBY610.10
6″50 4
S A-CBY65-S12.00
Made with chemically
These canton flannel treated (86 x 80) weave
buffs are made with muslin for added stiffthicker, softer fabric. ness and longer life. The
Excellent for final polishing
additional stitching and
with rouge on precious metals
leather + shellac (L/S)
(especially good on high karat gold and silver).
center keeps wheel stiff
Center pin holes are reinforced with shellac (S) while in use. Used for cutting and polishing in
for a tight fit on tapered mandrels.grooves, crevices and inside curves.
Rows of
Center
Part
Price Dia.Ply Dia. Ply Stitching Hole
No.
Each
S A-CFB3
Small diameter buffs mount on mandrels for
use in Foredom Handpieces. White Muslin
A-CB2 and A-CB12
are made from fine
(80 x 80) weave
muslin for use
with all types of
compounds. They
work with A-M1, A-M6, A-M7, A-M13,
and A-M15 mandrels.
Rows of Part
Price
Each
1″3/16″
16 2 A-CB2$1.50
1-1/2″3/16″
16 3 A-CB122.60
Square Edge Solid Felt Buffs
Square Edge Solid Felt Buffs shown below are
made from tightly compressed, top quality wool felt and come in Medium and Hard
densitities. Use for polishing and lapping flat
surfaces. They will hold an edge for working in
angles and corners.
1/2″, 5/8″, 3/4″ Priced per 10-Pk 2″ & 3″ Priced Ea
Arbor Hole Sizes:
1/16″ for A-SE1, A-FB4
and A-FB3
1/8″ for A-SE4 and A-SE5
Razor Edge Yellow Treated Buff
Flannel (Canton) Buff
3″30 2
2″ and Smaller Diameter Buffs for
use with Mandrels in Handpieces
Dia. Thick Ply StitchingNo.
Made with chemically treated extra fine (86 x
80) weave fabric, these buffs are stiffer than
untreated ones. They will cut faster and last
2 to 3 times longer than white muslin buffs.
Combed edges hold compounds without break
in or combing. Center pin holes are reinforced
with shellac (S) or leather and shellac (L/S).
4″40 3
Each
2″Tapered1 L/SA-CBGT2 $18.90
holds compound well but the tighter weave
results in longer life. The center pin holes
are reinforced with shellac (S) for a tight fit
on tapered mandrels and greater durability.
Combed edges do not require break in or
combing to hold compound. The fine weave
and stitching make them durable and especially suitable for polishing with rouge.
3″40 3
No.
2″Round 1 L/SA-CBGR2 $18.90
Fine Weave (80 x 80) Finex Muslin
Price Each
Fine weave cotton goblet style buffs have
round-ends that are shaped to conform to the
inside of a bowl or goblet. Use with polishing
compound to add luster to any metal or Carnauba Wax for use on turned wooden pieces.
Price Rows of Center Part
Dia. Shape StitchingHole
*Extra thickness eliminates need for leather reinforcements.
Part
No.
Fine Weave
Cotton
Goblet Buffs
$5.00
4″
at center. 12 ply
28 at outside
edge.
Center
Hole
L/S
Hardness
1/2″1/8″
Medium
A-SE1M$6.10
1/2″1/8″
Hard
A-SE1H$6.10
5/8″3/16″
Medium
A-FB4$5.90
3/4″1/4″
Medium
A-FB3$7.80
2″3/8″
Medium
A-SE4M$4.70
A-CYR4$6.30 3″1/2″
Medium
A-SE5M$12.60
Price Each
Part No.
10-Pk Price
Thick
Part
No.
Dia.
Sold Individually:
FOREDOM®
17
Screw and Tapered Mandrels
Made in USA and Germany
Screw and tapered mandrels are nickel plated except for black oxided A-M30, A-M31, A-M3, A-M16 and A-M89. A-M8 has no plating or oxide.
Part Numbers and Prices are shown in red
on each page.
Screw Type Mandrels
Head
Diameters″
Part Arbor Hole/ Overall Price No. Shank″ Capacity″Length″Each
3/16
A-M1 3/321/16 1-3/4$1.3040,000
Max
Speed
A-M103/32 1/16
7/8
5/16
A-M133/32 1/16
1-7/8 2.4030,000
5/16
A-M14 1/8
1-7/8
2.4030,000
A-M8 1/8 1/4 1-11/16
6.1020,000
3/16
A-M15 1/8 1/16
1-3/4
1.9040,000
5/16
A-M19 1/8 1/16
1-7/8
2.4030,000
3/16
A-M2 3/32 1/8
1-7/8
3.1020,000
Part Arbor Hole/ Overall Price No. Shank″ Capacity″Length″Each
3/16
A-M6 1/8 1/16
1-3/4
1.9040,000
A-M12 1/81/8 1-3/4
$1.9040,000
3/16
A-M20 1/8 1/8
1-3/4
1.9020,000
A-M3 3/32 3/32
7/16
A-M831/8 1/8
2-1/8 2.4020,000
7/16
A-M841/4 1/8
2-1/8 2.4020,000
7/16
A-M851/4 1/4
2-1/8 2.4020,000
3/16
3/8
1/8
1.9040,000
Maximum and Recommended Speeds vary depending on the
type and size of the accessory as well as the mandrel in use.
Maximum speeds shown are based on a 1″ overhang with an accessory that weighs under 1 gram and is smaller than 1/2″ in diameter.
As a general rule, smaller accessories and mandrels can be used at
higher speeds than larger accessories and mandrels. It is a good idea
to follow the recommendations that come with both the accessory and
mandrel you are using.
Screwdriver A-PS83 $4.70
5″ long, double ended screwdriver fits many of the small size screws
we use on mandrels, flex shaft motor connectors and other products.
Has both flat blade and phillips tip and pocket clip.
Tapered Mandrels
1-3/4
Max
Speed
1.9040,000
A-M91/8 3/32 1-3/4 1.9040,000
A-M7 1/8
1-3/4
1.9040,000
A-M78 1/8 3/16 2-3/8
4.1020,000
A-M16 1/8 1/8
4.7518,000
1/8
2-3/4
For use with cartridge rolls
3/4
A-M30 1/4 3/8 1-5/8
3.3525,000
For use with 1″, 2″ & 3″
Buffs, see page 17.
2″ Velcro Hook Sanding Heads with 3/8″ arbor holes, featured
on page 31, can be mounted onto A-M30 & A-M31 mandrels
for use in Foredom Handpieces.
3/4
Visit our website for sandpaper
template
A-M31 1/4
3/8
2
6.60 25,000
Sandpaper Split Mandrels
These nickel plated mandrels have slots
for inserting and wrapping small pieces
of sandpaper. 20,000 RPM Max Speed
A-M89 1/4 3/8
Adapters for Mounting Accessories on to BL Lathe
These adapters are used to mount accessories onto the tapered spindles of
Foredom’s BL Bench lathe. Use the A-4561 and A-4562 for 3M ScotchBrite
Radial Bristle Discs and wheels with 3/8″ arbor holes. The A-4568 is for
mounting FX & other wheels with a 1″ holes. 10,000 RPM Max Speed
Slot
Head
Lgth″ x Overall Price Dia″Width″Length″ Each
Side of Part No. Lathe Arbor Price
Hole″Each
A-4561 Right Hand
Side
3/8
$2.30 A-M233/325/32 3/4 x 1/32 2-3/8 1.90
A-4562 Left Hand
Side
3/8
$2.30
A-M24 3/32 3/32 3/4 x 1/64 1-3/4 1.30
A-M24LG 3/32 3/32 1/2 x 1/64 2-3/16 1.30
Part
No. Shank″
A-M21 3/32 1/18 3/4 x 1/32 2-3/8 $1.90
1/16 at tip
A-M22 3/32 5/32 3/4 x 1/32 2-3/8 1.90
A-4568 Both Sides
A-M26 1/83/16 3/4 x 1/32 2-3/8 2.10
18
2-1/2 11.0018,000
FOREDOM®
1
$5.80
Rubber Drum Mandrels
Made in USA
Rubber drum mandrels are black oxide except for nickel plated A-SD40
3/32″ and 1/8″ Shank
3/32″ shank Part No.
Price Each
1/8″ shank
Part No.
1/4 1/21-7/8 40,000
A-SD324
A-SD184$3.70
1/4 1/22-1/4 15,000
A-SD40$4.00 3/8 1/21-7/8 40,000
A-SD326$4.00 A-SD186$4.00
1/2
1/2
1-7/8
40,000 A-SD328$4.40 A-SD188$4.60
3/4 1/2 1-7/8
20,000
Not Available
A-SD189$4.60
Head Head
Total
Dia.″Length″Length″
Part No.
1/4″ Shank
Max Speed
RPM
HeadMax
Dia″ x
Price Speed
Length″
Each RPM
$3.70 Price Each
Not Available
A-SD141 1/2 x 1 $6.2020,000
A-SD661 6mm Shank A-SD143 3/4 x 1/2 $4.8020,000
A-SD144 3/4 x 1
$4.9015,000
A-SD662 6mm Shank
A-SD145 3/4 x 1-1/2 $10.5010,000
Includes wrench. 2-3/4 overall length
Left Hand Threaded Mandrels with 3/32″ Shanks–
For running in Reverse Operation
Micro Chucks and Collet Adapters
Nickel plated Micro Chucks A-M50 and A-MC2 hold various sizes
drills and have 1/4″ head dias. A-M53 also has a 1/4″ head dia. &
holds 3mm rod accessories. Collet Adapter A-M52 (3/16″ head dia.)
and HPL4 part nos. are used to “step down” the collet size without
having to actually change the collet in your handpiece. This is a
great way to easily use a smaller diameter shank accessory quickly
without any of the work involved with changing collets.
A-M50, A-M53, A-MC2 &
A-M50 3/32 2-1/4
The left handed threads on these mandrels hold accessories securely and
self tighten while running in reverse in flex shafts and micromotors. They
have notches on their shanks for easy identification. A-SD324L, A-SD326L
and A-SD328L also have black left hand threaded screw tops.
Part No.
A-M1L & A-M7L are nickel
plated. A-SD324L, A-SD326L
& A-SD328L are black oxide
1/16 1-3/4$2.40
A-M7L
1/8 1-3/4$1.90
Part No.
A-SD324L
Head Dia″/Overall Price
Length″Length″Each
1/4 x 1/2 1-3/4
$8.00
A-SD326L3/8 x 1/2 1-3/4
$8.00
A-SD328L
drills 70-80$6.70
A-M53 3/322-1/163mm rods$3.15
A-MC2 1/8 1-5/16 drills 60-80$17.50
Arbor Hole/ Overall
Price
Capacity″Length″Each
A-M1L
Overall
Use
Price
Part No. Shank″Length″With Each
1/16″ shank
grip
A-M523/321-3/4 friction
$9.50
burs
A-M52 20,000 RPM Max Speed
Collet
Adapters
$16.30 Ea
1/2 x 1/2 1-3/4 $8.00
Adapters fit inside existing collet and allow
the use of smaller shank size accessories.
Great for use in micromotor and collet style
flex shaft handpieces.
3/32″ to 1/16″ shank
HPL4-32333/32 accessories
1/8″ to 1/16″ shank
3mm to 3/32″ shank
HPL4-32353mm accessories
1/8″ to 3/32″ shank
3mm to 1.6mm shank
HPL4-32373mm accessories
FOREDOM®
19
Rubber Sanding Disc Mandrels
Made in USA
Run in Forward Direction ONLY
Screw-Lok
(plastic). See
page 29 for
accessories
1/4-20
thread
A-M4A-M338
1/8
1/8
1/2
1-3/4
1-1/2
2
15,000
10,000
$6.80$10
A-M33
1/4
1-3/4
2
10,000
$10
A-M335
1/4
1-3/4
1-1/4
10,000
$10
Hook & Loop Add Ons Turn 2″ Disc Mandrels
'Velcro® Friendly'
A-10040 Discs with Velcro Hook on one side & PSA on the other and
A-10041 Discs with Velcro Loop on one side & PSA on the other are
needed to adhere and re-use 2″ PSA backed Sanding Discs (see pages
31-32) with A-M338, A-M33 and A-M335 Mandrels.
Here's How it's Done:
1. Remove the psa covering from a A-10040 Velcro® Hook Disc and press
the sticky side down onto the mandrel surface.
2. Remove the psa coverings from a A-10041 Velcro® Loop Disc and any
2″ Sanding Disc and stick together. (You will want to dedicate a Loop Disc
for every Sanding Disc, so be sure to keep a good supply on hand. PSA
backings do not retain enough sticking power if separated for use with
other Discs.)
3. Now join the Velcro loop surface on the back side of the Sanding Disc
to the Mandrel's Velcro Hook surface. It's that easy!
A-10040-5 $6.00/5-Pk
A-10041-5 $4.40/5-Pk
A-10040
Velcro Hook
A-10041
Velcro Loop
Part No.
A-M34
A-M36 1/4 1/4 Shank
2-3/4 1-3/4 Dia.″
Overall Length″
2
2
Max Speed - RPM
10,000
18,000
Price Each
$10.50 $6.60
Mandrels, Hubs, and Arbor for Mounting Accessories to
Angle Grinder:
These special mounting tools are used to attach 2″ Sanding & Grinding
accessories onto Foredom’s Angle Grinder Attachment See pages 28 - 32.
Maximum Speeds vary depending on the type and size of the accessory.
A-69222 $6.30
2″ Velcro Hook
Backed Rubber
Disc Mandrel
8mm x 1mm thread
For mounting PSA
Sanding Discs with
A-40041 Velcro Loop
backed PSA Discs
A-69212$4.00
Short Hub
Includes 8mm Hex
Screw UA690
Short and Long Hubs are used for mounting
Radial Bristle Discs and Grinding Wheels
Screw-Lok Mounting Options:
A-69225 $5 2″ Screw-Lok Plastic Disc Mandrel
Screws onto Angle Grinder with 8mm x 1mm thread. Has
threaded hole for attaching discs with plastic screw-lok backs
(see page 29) or use with NEW Screw Lock Discs A-3702, 3704
and 3705 shown below and detailed at right.
NEW
A-69225A-3705
A-3705
Screw-Lok Velcro Hook
Screw Lok
Mandrel
Disc FRONT
Disc BACK
A-69212L$4.00
Long Hub
Includes 14mm Hex
Screw UA691
NEW
A-3705 $1.70
Screw-Lok Disc
2″ (50mm) with Velcro
Hook Front
A-3702 $1.00
Screw-Lok Disc
1″ (30mm) with Velcro
Hook Front
A-3704 $1.30
Screw-Lok Disc
2″ (50mm) Plain Front
Bench Lathe Polishing & Sanding Kits
Wayne Werner, jeweler, craftsman and Foredom demonstrator, developed these Kits for use with our BL Lathe.
AK3371 $255
Wayne Werner
Polishing Kit, 57-Pc
AK3375 $84
Wayne Werner
Sanding Kit, 28-Pc
Total Value
Over $275
57-Pc Kit to pre-polish and polish precious metals, finish pewter, and
white metals. Also remove scratches and sprue marks, clean insides
of rings and solder joints. Includes–2 ea. of 3″ Soft Cotton and
Square Edge Felt Buffs, Bars of Platinum Blue & White Compound, 6
ea of 3″ Scotch-Brite Radial Bristle Discs in 80, 120, 220, 400, 1,200,
3,000 and 14,000 grits, and 9 Tapered Spindle Adapters for right &
left side mounting. 7,000 RPM Max Speed
Total Value
Over $91
28-Pc Kit for use with
the collet holder with
1/4″ collet installed that
comes in our K.3340
Bench Lathe Kit. These bands and discs are some of Wayne's favorite
products! Contains 3 ea. of 1/2″ x 1″ Trizact Sanding Bands and 2 ea.
of 3″ Trizact Sanding PSA Discs in 400, 600, 1,200 & 2,500 grits. Also
4 ea. of 1/2″ x 1″ Sanding Drum Mandrels with 1/4" shanks & 3″ Dia.
Disc Mandrels. 10,000 RPM Max Speed
20
FOREDOM®
Assortment Kits
General Use– AK20, AK21 & AKHK10
AK20 $55
35-Pc Kit
Jewelry
AK11 $68
43-Pc Kit
3/32″ Shanks
Total Value Over $124
3/32″ & 1/8″
Shanks
Total Value
Over $60
35-Pc Assortment contains steel cutters and burs, mounted points, wire
and bristle brushes, rubber bonded abrasives, sanding drums and felt
bobs. 20,000 RPM Max Speed
Comes in Foredom Prepacked
Jewelers K.2200, K.2220, K.2230
& TX300 Power Tool Kits. Includes rotating bur and tool holder and
tube of platinum white compound, a V Stone, 3M Radial Bristle Discs
with screw mandrel, 12– 1/4 x 1/2 Ceramic Purple Sanding Bands
in various grits, rubber drum mandrel, 3 rubber bonded and 3 'CW'
polishing wheels, cut off disc, felt buff, 5 mounted brushes, and 4
fluted engraving burs, 25,000 RPM Max Speed.
Woodcarving– AKWK53, AK22, AK23
AK21 $150
88-Pc Kit
AKWK53 $126
27-Pc Kit
3/32″ & 1/8″ Shanks
3/32″, 1/8″, 1/4″ Shanks
Total Value
Over $157
88-Pc Assortment comes packed in our General Applications Kit
K.2272. Contains some of our most unique rotary accessories: Ceramic
Purple Abrasive Bands, V Stone Mounted Abrasives, and CeramCut
Blue Stones. Also plated diamond points, steel cutters, aluminum oxide
points, rubber bonded abrasive wheels, wire and bristle brushes, felt
buffs and bobs, tube of red polishing rouge, various mandrels.
AKHK10 $39
10-Pc Kit
10-Pc Assortment includes
3 CeramCut Blue Stones,
2 carbide burs, 2 mounted
felt bobs, sanding band
and sanding drum mandrel,
screw type mandrel.
1/8″ Shanks
Total Value
Over $43
Dental Lab
AK3361 $140
30-Pc Kit
Comes in all Foredom Prepacked
Woodcarving Power Tool Kits.
Includes rotating bur and tool holder
and 3 Typhoons in 1/4″, 1/8″, and
3/32″ shanks, 3 Ceramcut Blue and 1 V Stone, 2 plated diamonds, 1
vanadium steel cutter, 3M Radial Bristle Disc, 12 1/2 x 1/2 Ceramic
Purple Sanding Bands in various grits, and rubber drum, screw and
sandpaper split mandrels. 25,000 RPM Max Speed, 10,000 RPM
on 1/4″ Typhoons.
AK22 $385
Frank Russell Kit, 33-Pc
3/32″, 1/8″, 1/4″ Shanks
33-Pc Kit contains the burs Frank Russell uses in his DVD, “Fur, Feathers and
Fins”. According to Frank, these are the
ones needed for any carving you can
hold in your hand. Dominated by Foredom’s exclusive Typhoon® carbide burs
in coarse and fine grit, the kit includes
13 Typhoons in 1/4″ and 1/8″ shanks, 8 Ceramcut Blue Stones,
3 plated diamonds, 1 vanadium steel cutter, 1 carbide bur, 3 ruby
carvers, and sandpaper split mandrel. Also, 2″ fine bristle nylon brush
with tapered mandrel and rotating bur and tool holder.
25,000 RPM Max Speed, 10,000 RPM on 1/4″ Typhoons.
AK23 $195
Frank Russell
Basic Kit, 22-Pc
Total Value
Over $146
30-Pc Kit for polishing Valplast , Flexite , and other nylon denture
materials. The larger diameter accessories are for use on the tapered
spindle of Foredom’s BL Lathe. Includes: 6-Pks of 3″ Scotch-Brite Radial
Bristle Discs in 80, 220, 400, & 14,000 grit. Also 3″ cotton buff, 2 right
& 2 left side spindle adapters, and bar of platinum white polishing
compound. 7,000 RPM Max Speed
®
3/32″, 1/8″, 1/4″
Shanks. Total Value
Over $205
®
We reserve the right to substitute comparable accessories when necessary.
22-Pc Kit is a scaled down version of AK22 above. Includes 2–1/4″
and 3–1/8″ shank Typhoons, 7 Ceramcut Blue Stones, 4 plated
diamonds, 3 ruby carvers and a steel cutter. Also, 2″ fine bristle nylon
brush with tapered mandrel. 25,000 RPM Max Speed, 10,000
RPM on 1/4″ Typhoons.
FOREDOM®
21
Step, Twist & Carving Drills– Industrial Grade
Length
Step Drills
Diameter
3/32″ (2.35mm) Shank 30,000 RPM Max Speed
45mm (1.8″) Overall Length
Ordering Drills: Order Steel Step (at right)
& Twist Drills (below) by Wire Gauge Size.
Order Cobalt Steel and Diamond Plated Step
Drills by metric sizes of head diameters. Also,
Wire gauge sizes are precise for Cobalt Steel and Steel
Drills. Decimals shown in chart below are equivalents of
wire sizes and metric values are for reference only.
WireDecimal ″
Metric (mm)
GaugeEquivalent Equivalent
80.0135
79.0145
78
.0160 (1/64)
77.0180
76.0200
75.0210
74.0225
73.0240
72.0250
71.0260
70.0280
69.0292
68.0310
67
.0320 (1/32)
66.0330
65.0350
64.0360
63.0370
62.0380
61.0390
60.0400
59.0410
58.0420
57.0430
56.0465
55.0520
54.0550
53.0595
52.0635
51.0670
50.0700
47.0785
45.0820
40.0980
36.1065
Twist Drills
Order by
Wire Gauge
Sizes 36 – 80
20,000 RPM
Max Speed
Cobalt
Twist Drills
Made from hardened tool
steel. Use for drilling all
types of wood, precious
metal, mild steel, bone, and mother of pearl.
Wire
Gauge Head Lgth
Size
mm
Part No.
76
73
70
65
61
57
54
53
47
44
0.343
0.368
0.406
0.457
0.508
0.533
0.572
0.610
0.635
0.660
0.711
0.742
0.787
0.813
0.838
0.889
0.914
0.940
0.965
0.991
1.016
1.041
1.067
1.092
1.181
1.321
1.397
1.511
1.613
1.702
1.778
1.994
2.083
2.489
2.705
A-58005P
A-58006P
A-58007P
A-58009P
A-58010P
A-58011P
A-58014P
A-58015P
A-58020P
A-58022P
8.5
8.5
8.5
8.5
8.5
10.5
10.5
11.0
11.0
11.0
NEW PRIMO®
Cobalt Steel Pilot
or Center Drills
$12.00 Ea
Used to make starter holes
to prevent your drill bit from
wandering in most metals.
Double ended, 45mm long,
2.35mm shanks.
head dia. 0.5 mm
A-8401
head dia. 1.0 mm
A-8403
AK8400 $32 3-Pc
One of each Pilot Drill
Cobalt Steel Twist Drills $13.10/10-Pk
50
51
52
53
54
55
56
57
58
59
A-8350
A-8351
A-8352
A-8353
A-8354
A-8355
A-8356
A-8357
A-8358
A-8359
60
61
62
63
64
65
66
67
68
69
A-8360
A-8361
A-8362
A-8363
A-8364
A-8365
A-8366
A-8367
A-8368
A-8369
Wire Gauge
Size Part No. 70
71
72
73
74
75
76
77
78
79
80
A-8370
A-8371
A-8372
A-8373
A-8374
A-8375
A-8376
A-8377
A-8378
A-8379
A-8380
22
Diamond Plated
Step $7.80 Ea
Drills are solid cobalt steel and
outlast high speed steel (HSS)
bits 15 to 1. Drills with * are in
Kit AK8000 below.
Drills feature excellent balance, precision & consistent
diamond coverage. Drills
with * are in Kit AK8100
below. Equivalent wire gauge
sizes are approximate.
Head
Dia.
mm's
.5
.6
.7
.8
.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
2.0
2.1
2.2
2.3
Head Lgth
Head Lgth
mm
Part No.
mm
Part No.
10.0
A-8005*
10.0
A-8006
10.0
A-8007*
10.0
A-8008
10.0
A-8009*
10.0
A-8010
10.0
A-8011*
10.0
A-8012*
Not Available
10.0
A-8014*
10.0
A-8015
10.0
A-8016*
10.0
A-8017
10.0
A-8018*
10.0
A-8020*
10.0
A-8021
10.0
A-8022*
10.0
A-8023
Not Available
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
A-8107
A-8108
A-8109
A-8110*
A-8111
A-8112
A-8113*
A-8114*
A-8115
A-8116*
A-8117
A-8118*
A-8120
A-8121*
Not Available
A-8007, A-8009, A-8011, A-8012, A-8110, A-8113, A-8114,
A-8014, A-8016, A-8018, A-8020, A-8116, A-8118 and A-8121.
and A-8022.
A-8402
head dia. 1.5 mm
Wire
Gauge
Size Part No.
PRIMO®
Cobalt Steel
Step $8.40 Ea
10-Pc Cobalt Kit
6-Pc Diamond Plated Kit
AK8000 $82 Includes: A-8005, AK8100 $48 Includes:
PRIMO®
Wire Gauge
Size Part No.
PRIMO®
Steel Step
Drills
$2.80 Ea
PRIMO®
Diamond Plated
Twist Drills
Diamond
$23/5-Pk Plated
Twist Drills wire
Wire
gauge sizes are
approximate.
Gauge
Size≈
Part No.
36
40
45
47
50
51
52
53
54
56
61
65
A-8236
A-8240
A-8245
A-8247
A-8250
A-8251
A-8252
A-8253
A-8254
A-8256
A-8261
A-8265
FOREDOM®
Steel Carving
Drills $19.40 Ea
Made in USA
Premium tapered carving drills
made of high tempered steel
with three flutes. Designed for
internal carving and shaping
of wood, acrylic and plastic.
1-3/4″ oal, 3/4″ drill head
1/16″ shank A-CD1
3/32″ shank A-CD2
1/8″ shank A-CD3
Twist Drills– Standard Grade
20-Pc Diamond Twist Drill Set AK2061 $16.30
Diamond Needle File Sets
Diamond coated, wire gauge
twist drill set in plastic dispenser.
These straight shank drills are
made of high quality steel with
diamond coating. Set contains
one each of drills #61 to #80
See Chart on previous page
Fine Point 5-Pc Set
A-F37352 $19.40
5-1/2″ long Diamond Needle Files
provide aggressive yet precise shaping
on glass, metal, ceramics, marble, wood,
plastics, stone, bone etc. Fine Point Set
includes one each Round Taper, Triangle
Taper, Square Taper, Larger Round Taper,
and 1/2 Round Taper.
Use any of these twists drills in small pin vises that hold wire gauges or in
a rotary handpiece with A-M50 and A-MC2 micro chucks, see page 19.
Two High Speed Twist Drill Sets – Wire Gauge
Size and Metric Sets
20-Pc High Speed Steel Twist Drill Set
37-150 $16.30
Miniature drill set in plastic dispenser with one each
of high speed twist drills in wire gauge sizes #61 to
#80
20-Pc Metric High Speed Steel Twist Drill
Set 37-151 $16.30
Miniature twist drill set in plastic dispenser with one
each of high speed twist drills in metric sizes from
0.3mm - 1.6mm. Includes: 0.3, 0.35, 0.4, 0.45, 0.5,
0.55, 0.6, 0.65, 0.7, 0.75, 0.8, 0.85, 0.9, 0.95, 1.0,
1.2, 1.3, 1.4, 1.5, and 1.6.
Speed Recommendations:
Drilling speeds should be between 500 and 10,000 rpm. All drilling
should be done with a lubricant. The harder the material (metal) to
be drilled and the larger the hole size, the slower the drill speed.
Material
1mm (1/16″) Drill 2.35mm (3/32″) Drill
Aluminum
7,000-8,000
5,000-6,000
Mild Steel
3,000-3500
2,000-3,000
Stainless Steel
1,000-2,000
500-1,000
Brass, Silver, Copper 5,500-6,500
4,000-5,000
Fine Point Set
Flat Shape 5-Pc Set
A-F37354 $19.40
5-1/2″ long Diamond Needle Files
provide aggressive yet precise shaping
for any hobby on glass, metal, ceramics,
marble, wood, plastics, stone, bone etc.
Shapes included in Flat Set are Triangle
Taper, Flat Taper, Flat, Knife Taper, and
Oval Taper.
Flat Shape Set
Needle File Sets come packed in a sturdy reusable plastic case.
Carbide Cutting, Carving & Sanding Accessories
1/8″ Shank Mounted Carbides 35,000 RPM Max Speed
Cutting Wheel
A-6613
DuraGrit accessories are coated with super strong and long lasting tungsten
carbide grit that will not tear loose. Their edges stay sharp and are thin
enough for cut off applications. Use to cut, carve, sand and shape on wood,
plastic, laminates, fiberglass, ceramic tile, kevlar, leather, rubber and styrofoam.
A-6611 $18 Sanding/Shaping Wheel, 1-1/4″ dia., 1/8″ arbor hole, 46 grit. Shaping
Mushroom-type design is good for producing compound curves. Use for fast Wheel
material removal, sculpting, and sanding.
A-6611
A-6613 $18 Cutting Wheel, 1-1/2″ dia., 1/8″ arbor hole, 60 grit. Has thin
kerf and makes deep, clean cuts. Perforated surface promotes cool running
and reduces clogging. Use to cut hard & soft woods, MDF & pine moulding,
fiberglass, ABS plumbing, PVC piping, rubber hose, laminate flooring, etc.
A-6621 $16 Hollow Cylinder, 1/2″ dia., 60 grit. Use to create channels,
bevels and corners or smooth rough surfaces. Functions as 1/2″ sanding
Hollow
band but doesn't need drum mandrel. Has grit on the edge opening and
Cylinder
doubles as a hole saw.
A-6621
A-6624 $13 Tapered Point, 1/8″ dia., 80 grit. is ideal for drilling curved
shiny surfaces. Also for detail work in carving, modelling and general crafts.
Tapered
Point
A-6624
NEW
4-Pc Set
AK6600 $60
Includes A-611, A-6613,
A-6621, A-6624 and
small square burs stand
with clear cover
FOREDOM®
23
High Speed Steel Cutters High Speed
Steel Fluted
Engraving Burs
Superior quality high speed steel cutters for shaping, grooving, slotting and cutting
in wood, plastic and soft metal.
1/8″ (3.18mm) Shank Priced Below
Made in Switzerland.
A-7104A-7106A-7112 A-7113 A-7122 A-7143 A-7145 A-7153 Part No.
$9.70$10.90$8.50 $10.90$10.90 $10.90 $10.90$10.90 Price Ea
3/16″5/16″1/8″5/16″5/16″1/4″3/8″3/8″ Head Dia.
3/16 5/16 1/4
3/8 13/32 15/32 9/16 1/16″ Head Lgth
1-7/16″1-9/16″1-9/16″1-1/2″1-7/16″1-1/2″1-1/2″1-1/2″ Overall Lgth
Miniature Carbide Burs
These and Ball Shape Burs below Made in Germany and Belgium.
2.35mm (3/32″) Shank
$1.50 Ea 1-3/4″ Overall Length
3 Ball
Shapes
Part No.
A-R2
A-R5
A-R7
1/32″ (.79)1/16″ (1.6)3/32″ (2.35) Head Dia.
(mm)
1/32″ (.79)1/16″ (1.6)3/32″ (2.35) Head Lgth (mm)
2.35mm (3/32″) Shank, 1-3/4″ Overall Length
$4.90 Ea Except A-TR-5C $22 Ea
2 Inverted
Cones
Cross Cut Cross Cut
Part No.
A-P3A-P7
1/32″ (.79)
3/32″ (2.35) Head Dia. (mm)
3/64″ (1.19) 5/64″ (1.98) Head Lgth (mm)
1-9/16″
Overall
Length
Taper
Inverted Cone
Cylinders
Ball Nose
Tree Pt
A-203**A-208**A-240*A-204**A-207**A-205**A-206**A-TR-5C
1.191.62.351.61.6 1.191.62.35
4.37
1.6
1.6
4.37
4.37
3.97
3.97
6.35
5-Pc Kit AK65 $6 A-R2, A-R5, A-R7, A-P3, A-P7
Shape
Part No. Ea
Head Dia. mm
Head Lgth mm
Miniature Carbide Ball Shape Burs
For etching, engraving, & other fine detailing on
metal, wood, glass, ceramics, etc.
2.35mm (3/32″) Shank, 1-3/4″ Overall Length $4.90 Ea Except A-212 & A-213 $8 Ea
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
1-9/16″
Overall
Length
Ball Shape Miniature Carbides
Part No.
A-212**A-213 A-214 A-215**A-216 A217**A-201***A-219A-220**A-222 A-224 A-226 A-228 A-230**A-202***
Head Sizemm
0.20.30.40.50.60.70.790.91.01.21.41.61.82.1 2.35
Miniature
Carbide
Bur Kits
Packed in Round
Bur Stand with
Clear Cover
Ball Shape Kits–
AK211 $34.65 7-Pc Ball Burs Shown with *
AK212 $75.00 15-Pc All Ball Shape Burs A-212, A-213, A-214, A-215, A-216, A-217, A-201,
A-219, A-220, A-222, A-224, A-226, A-228, A-230 and A-202
Assorted Shape Kits–
AK200 $36.75 8-Pc Shown above with * Includes: A-201, A-202, A-203, A-204, A-205, A-206,
A-207 and A-208
AK210 $67.20 14-Pc Burs Shown with * A-203, A-208, A-240, A-204, A-207, A-205, A-206,
A-212, A-215, A-217, A-201, A-220, A-230 and A-202
24
A-212, A-215, A-217, A-201, A-220, A-230, A-202
NEW
FOREDOM®
Tungsten Carbide Burs
Made in USA
Tungsten Carbide Burs are used for easy material removal and leave a smooth finish. They are ideal for use on hard
wood and most metals including stainless steel, steel alloys, cast iron, etc. 100,000 RPM Max Speed for 1/8” and
smaller head diameter carbides, 35,000 RPM Max Speed for 1/4” head diameter carbides.
1/8″ (3.18mm) Shank Priced Below
Ball
Cone
Cylinder Square
Cylinder Radius
A-B-1 A-B-2 A-CO-2A-CO-3 A-CP-1 A-CP-2 A-CP-3 A-CR-1A-CR-2A-CR-3
$11.40 $16.20 $11.40$16.20 $11.40 $11.40 $16.20 $11.40$11.40$16.20 Shape
Price Ea
Part No.
Head Dia.
1/8″1/4″1/8″1/4″3/32″1/8″1/4″3/32″1/8″1/4″
Head Length
1/8″1/4″5/8″5/8″7/16″9/16″1/2″7/16″9/16″1/2″
Overall Length
1-1/2″1-3/4″1-9/16″2-1/8″1-9/16″1-9/16″2″1-1/2″1-1/2″2″
Flame
Inverted Cone
Oval
Tree Point
Tree Radius
Shape
Part No.
A-F-1 A-IC-1A-IC-2 A-OV-1A-OV-2 A-TP-1A-TP-2A-TP-3A-TR-2 A-TR-3
$11.40 $11.40$16.20 $11.40$16.20 $11.40$11.40$16.20 $11.40 $16.20 Price Ea
Head Dia.
1/8″1/8″1/4″1/8″1/4″1/8″1/8″1/4″1/8″1/4″
Head Length
1/4″3/16″1/4″7/32″3/8″1/4″3/8″1/2″1/2″1/2″
Overall Length
1-9/16″1-1/2″1-3/4″1-1/2″1-7/8″1-9/16″1-9/16″2″1-1/2″2″
Rotating Bur & Tool Holders
Burs and small tools not included. A-10082 $16.50 Rotating Bur and
Tool Holder– For 1/8″ and 1/4″ Shank
Burs, Drill Bits 1/16″– 5/32″.
Organizes up to 112 accessories. Stores:
92– 1/8″ shank & 13–1/4″ shank burs.
Has 7 marked holes for drill bits 1/16″
to 5/32″. 3″ deep x 2-3/4″ dia. center
cup holds small tools such as files and
screwdrivers. Measures: 6-1/2″ wide x
4″ high (165 x 102mm). Made in USA
Small Bur Holders
with Covers
A-10089 $4 Small Square Bur Holder–For 3/32″
(2.35mm) & 1/8″ Burs. Holds up to 52 burs: 34–3/32″
and 18– 1/8″ shank accessories. Measures: 2-1⁄2″
(64mm) sq. x 2-1⁄4″ (54mm) high. Holds burs up to 2″
long. Includes clear cover.
A-10080 $16.50 Rotating Bur and
Tool Holder– Universal–For ALL Size
Shanks. Organizes 126 accessories with
1/16″, 3/32″, 1/8″, and 1/4″ shanks.
Measures: 6-1/2″ wide by 4″ high (165
x 102mm) and holds 69– 3/32″ or 1/8″
burs (in 2-step holes),12–1/4″ burs, and
45– 1/16″ burs.
A-10088 $4 Small Round Bur Holder– For 3/32″
(2.35mm) & 1/8″ Burs. Holds up to 48 burs with 24
holes for each size shank. Measures: 2-1⁄8″ in dia.
x 2-1⁄2″ high (54 x 64mm). Holds burs up to 2″ long.
Includes clear cover.
A-10081 $16.50 Rotating Bur
Holder– For 3/32″ (2.35mm) Burs
and Small Tools. Stores and organizes
114– 3/32″ burs. Measures: 6-1/2″
wide by 4″ high (165 x 102mm) and has
a center cup (3″ deep x 2-3/4″ dia.) to
hold small tools such as files, scribes & screwdrivers.
FOREDOM®
25
Tungsten Carbide Burs– 2.35mm
and 1/8″ Shanks Made in USA. 35,000 RPM Maximum Speed
®
Typhoons have unique structurally aligned tungsten carbide points that last long and do not
load quickly. Use the fine grits for general shaping and sanding. The coarse grit is for even more
rapid and aggressive shaping and roughing out work. Typhoons are ideal for use on hard and
soft woods, acrylic, die stone, plaster, hard rubber and fiberglass.
2.35mm (3/32″) Shank Fine (Blue) Grit Individual Burs $20.80 Ea
AKHK83
$59 3-Pc
Typhoon Kit
2.35mm shanks:
A-KB32119,
A-KB32719,
A-KB32913
AKHK85 $80 4-Pc Typhoon Kit
in small round bur holder with cover
2.35mm shanks: A-KB32119, A-KB32315,
A-KB32519, A-KB32719
A-KB32315A-KB32119A-KB32915 A-KB32519A-KB32719 A-KB32913A-KB32415 Fine Part No.
Shape
Long Taper
Taper
Cylinder
Ball Nose
Flame
Bud
Ball
Head Dia.
5/16″3/16″7/16″5/16″5/16″5/16″5/16″
Head Length
5/16″3/4″5/8″1/2″1/2″1/2″3/4″
Overall Length
1-7/16″2″1-3/4″1-3/4″1-13/16″1-3/4″1-7/8″
1/8″ (3.18mm) Shank Coarse (Red) and Fine (Blue) Grits Individual Burs $17.60 Ea
(except A-KB18118, A-KB18119, AK18718 and A-KB18719– $19.90)
$19.90
$19.90
Coarse Part No.
A-KB18314A-KB18338 A-KB18118 A-KB18114A-KB18414A-KB18718A-KB18714
Fine Part No.
A-KB18315 A-KB18339 A-KB18119 A-KB18115 A-KB18415 A-KB18719A-KB18715
Ball
Ball Long Taper
Taper
Bud
Ball Nose
Ball Nose Shape
5/16″7/16″3/16″5/16″5/16″3/16″5/16″
Head Dia.
5/16″7/16″3/4″1/2″3/4″7/8″1/2″
Head Length
1-1/4″1-3/8″1-1/2″1-1/2″1-11/16″1-1/2″1-3/8″
Overall Length
Smooth End
AKHK84 $68
4-Pc Typhoon Kit
-KB18834 A-KB18914 A-KB18638 A-KB18514A-KB18524
A
A-KB18835 A-KB18915 A-KB18639 A-KB18515A-KB18525
Rotor Saw
Flame
Dove Tail
Cylinder
Cylinder
11/16″7/16″7/16″5/16″5/16″
3/16″5/8″1/2″1/2″1/2″
1-1/8″ 1-3/8″
1-9/16″
1-9/16″
1-1/2″
Coarse Part No.
Fine Part No.
Shape
Head Dia.
Head Length
Overall Length
A-HB58 $5 Brass Brush Overall Dimensions–5/8″ w x 5-3⁄4″ l.
Bristles–3/8″ w x 1-3⁄4″ l x 5/8″ h. Typhoon
Burs, Sanding Sleeves, and Discs are easy to
clean with the A-HB58 Brass Brush. It removes dust or
chips from between rows of carbide points. Caution–Do not use a file
card or steel brush to clean Typhoon burs and sleeves.
26
FOREDOM®
1/8″ (3.18mm) shanks:
A-KB18119
A-KB18834
A-KB18414
A-KB18715
A-AC1
$8.30 Abrasive Cleaner
Removes material from
around Typhoon points.
Restores clogged sanding bands, discs, cartridge rolls, and other
abrasives. Use it like a
giant eraser by holding
the accessory against
the block while running
to remove embedded
grinding debris. FOREDOM ELECTRIC CO.
3″ x 3″ x 1-1/2″
®
Tungsten Carbide Burs– 1/4″ Shanks
Made in USA. 25,000 RPM Max Speed for burs with heads less than 13/16″ (21mm) in diameter
and 10,000 RPM for burs with head diameters 13/16″ (21mm) or larger.
1/4″ (6.4mm) Shank Coarse (Red) & Fine (Blue) Grits. Priced Below
A-KB14714
A-KB14734
A-KB14715
A-KB14735
$20.40
$28
Ball Nose
Ball Nose
5/16″13/16″
1-3⁄4″1-1⁄4″
3″
2-1⁄2″
A-KB14712
A-KB14395
A-KB14312 Coarse P/N
A-KB14713
N/A
A-KB14313 Fine
P/N
AK490 $68
$20.40
$23.80
$20.40 Price Ea
3-Pc
Typhoon Kit
Ball Nose
Ball
Ball
Shape
1/4″
shanks:
A-KB14533,
9/16″7/8″9/16″
Head Dia.
A-KB14712, A-KB14979
3/4″7/8″9/16″
Head Length
2″
2-1/16″
1-3⁄4″
Overall Length
Smooth End
A-KB14978
A-KB14958 A-KB14912 A-KB14114
A-KB14178
A-KB14158 A-KB14198 Coarse P/N
Fine P/N
A-KB14979
N/A
A-KB14913 A-KB14115
A-KB14179
A-KB14159
N/A $28
$22 $19.50$20.50
$28
$20.50
$28
Price Ea
Flame
Flame
Flame
Taper 15º
Taper 15º
Taper 15º
Taper 5º
Shape
7/8″5/8″ 3/8″5/16″13/16″9/16″ 13/16″ (9/16)
Head Dia.
1-3/8″1-1/16″3/4″1-1⁄2″1-3⁄8″1″ 1-1⁄4″
Head Length
2-5/8″2-1/4″
2-1/16″
2-13/16″
2-1/2″
2-3/8″
2-1/2″
Overall Length
Smooth End
1/4″ Shank Sanding Sleeves
Priced Below Made in USA. 10,000 RPM Max Speed for use on
Foredom’s M.BL & other Bench Lathes
A-KB14534 N/AA-KB14522 Coarse P/N
A-KB14535 A-KB14533
N/A Fine P/N
$28
$23.20$20.40 Price Ea
Cylinder
Cylinder
Cylinder Shape
13/16″9/16″9/16″
Head Dia.
1-1⁄4″1-1⁄4″3⁄4″
Head Length
2-1/2″
2-1/2″
2″ Overall Length
Expert carver,
Frank Russell, uses
smooth end cylinder to shape side to
side without cutting
into the area above
the bur.
Shank
Size Grit
Outer
Dia.
Inside Sleeve Only Use on
Dia Length Part No.
Mandrel
Mounted
Part No.
1⁄4″ Coarse15/16″3/4″1/2″ A-KB43524 A-SD143 A-KB43525
$20.60$24
1⁄4″ Fine15/16″3/4″1/2″ A-KB43521 A-SD143 A-KB43522
$20.60$24
1⁄4″ Coarse15/16″3/4″1″ A-KB43544 A-SD144 A-KB43545
$26$30
6mm Coarse15/16″3/4″1″ A-KB43544 A-SD662 A-KB43546
$26$30
AK491 Sleeve Only Kit: Six A-KB43521 Fine Blue Sleeves $119
AK492 Sleeve Only Kit: Six A-KB43524 Coarse Sleeves $119
FOREDOM®
27
Angle Grinder Accessories– 2″ Wheels
Foredom’s 2″ Angle Grinder Attachment for H.30, H.30H and H.30SJ Handpieces is wonderfully versatile because of the vast selection of
accessories we offer for polishing, grinding, and sanding on virtually any material– metal, wood, stone, acrylic, ceramics, bondo, composites,
resin, fiberglass, rubber and more. Angle Grinder accessories featured below and on the next few pages attach with special mounting hubs
and mandrels. Various Angle Grinder accessories, when paired with different mandrels, can also be used in flexible shaft handpieces and the BL
Bench Lathe, see pages 20 and 33.
Part Numbers and Prices shown in red on each page.
®
2″ Tungsten Carbide Discs with 3/8” Arbor Holes $38 Ea Made in USA
Typhoons have unique structurally aligned tungsten carbide points that last long and do not load quickly. Use the
fine grits for general shaping and sanding and the coarse grit for more rapid and aggressive shaping and roughing
out work. Ideal for hard and soft woods, acrylic, die stone, plaster, hard rubber and fiberglass.
Mount with A-69212
Short Hub that comes
in Angle Grinder Kits,
See page 20.
Flat Face
Round Face
1 234
2″ Abrasive Wheels
with 3/8” Arbor Holes. Made in USA
Use Aluminum Oxide on high tensile, tough materials including stone, porcelain, glass, and steel. A-10054 Cup
Wheel for medium to fine finishing. A-10062 Tapered Wheel for med. to fine finishing. A-10063 Wheel for extremely
fine cutting. A-10068 Silicon Carbide for grinding, rough finishing, deburring, smoothing, cleaning low-tensile, brittle or 'smeary' type metals such as aluminum, brass, stainless steel, glass, stone, and non-metals. CeramCut Blue
Wheels A-10064 and A-10065 (Cup Shape) last 3 to 5 times longer and removes material faster. Can be used on
hardened and mild steel, steel alloys, chrome cobalt, titanium, platinum, other ferrous metals and wood.
Flat
Mount with
Side:
1/4″ 1/4″
work on 1/2″ flat
A-69212L
Long Hub
that comes in
Angle Grinder
Kits, See
page 20.
Working
Edge:
Knife Edge
1/4″
1/4″
Flat Face Discs
1 A-KB25626 2 A-KB25627 Grit
Coarse
Fine
Round Face Discs
3 A-KB25628 4 A-KB25629 Coarse
Fine
Aluminum Oxides Price Grit
1 A-10054 Cup $5.00 150
2 A-10062 Taper$5.00120
Use on Edge not Flat side
3 A-10063$5.00 400
Use on Edge not Flat side
Silicon Carbide
Price G
rit
4 A-10068 $6.80100 Use on Edge not Flat side
CeramCut
Blue Stones Price Grit
5 A-10064$5.00120 Use on Edge not Flat side
6 A-10065 12 3 45 6
1/4″ Carpenter and woodcarver,
Ted Knapp, uses a Typhoon Disc
to hollow out a decoy.
$8.90100 5/8″w, 1/2″ thick cup working face
1/4″
2″ Abrasive Flap and Cut Off Wheels with 3/8” Arbor Holes Flap Wheels $2.30 Ea Cut Off Wheel $1.90 Ea
Flap Wheels are made from aluminum oxide mineral and are used for fast clean-up and pre-polishing work. 10,000 RPM Max Speed. Fiberglass
Reinforced Cut Off Wheel is used to cut off, groove, & trim metal, wood, and ceramics, 2″ x 3/64″ thick, 60 grit, 30,000 RPM Max Speed.
Cut Off Wheel
Flap & Cut Off Wheels Mount with A-69212 Short Hub that comes in
Angle Grinder Kits. See Page 20.
1
2
3
4
5
28
FOREDOM®
6
Flap Wheels
P/N Ea Grit
1 A-2201 60
2 A-2202 120
3 A-2203 240
4 A-2204 320
5 A-2205 600
Assortment, 5-Pc– 1 Ea Grit:
AK2200 $ 10.30
Fiberglass Cut Off Wheel
6 A-D11 $1.90 Ea 60
Angle Grinder Accessories– 2″ Screw-Lok
Easy to use Screw-Lok accessories are similar to the 3M Roloc™, and commonly used in industrial, auto- Accessory with
motive, boating, arts & crafts, and other industries. We offer Abrasive Pads, Aluminum Oxide Sandpaper Screw-Lok Backing
Discs, and a Felt Wheel with plastic Screw-Lok backings for secure and easy attachment to our A-69225
Screw-Lok Plastic Disc Mandrel that comes in Angle Grinder Kits and separately. Screw-Lok accessories can also be used with certain flex shaft handpieces when mounted on our 1/4″ shank A-M36
A-69225 Screw-Lok
Mandrel, see page 20.
Mandrel, see pg 20
2″ Abrasive Pads with Screw-Lok Backing 10,000 RPM Max Speed Priced Ea
Long lasting, aggressive Screw-Lok 2″ pads for tough blending and finishing applications. Ideal for
deburring, oxide and fire scale removal, cleaning, blending and smoothing. Layered, durable unitized or
non-woven construction with Screw-Lok backing for secure and easy attachment to A-69225
Screw-Lok Mandrel or 1/4″ shank A-M36 Mandrel for use in handpieces, see page 20.
* A-3522 comes in Angle Grinder Kits 3/8″ Arbor Hole Version
Not Screw-Lok
1
2 3 45 6
7
Abrasive Pads:
Part No. PriceThick″ Grit / Type
1 A-3512 $5.25 9/16 Ultra Rough
Unitized
2 A-3514$5.25 19/32 Rough
Unitized
3 A-3522* $2.30 5/32 80
Non-Woven
4 A-3524 $2.30 5/32 120
Non-Woven
5 A-3526 $2.30 5/32 240
Non-Woven
6 A-3527 $2.30 5/32 320
Non-Woven
Assortment, 6-Pc–
AK3500 $16.80 1 of pads above
7 A-10055 $10.50 1/4 Coarse
Use on edge or rim
Unitized
Aluminum Oxide Sandpaper Discs:
$1.10 Ea
Part No. Ea Grit
with Screw-Lok Backing $1 Ea 10,000 RPM Max Speed
1 A-3601
24
2″ Sandpaper Discs have holes which help to prevent clogging. They overhang their Screw-Lok plastic
2 A-3602*
40
backing for added flexibility and sanding contours. Available individually and in 10-Packs from 24 to 600 3 A-3603
80
grit. A 40 and 120 grit disc come in Angle Grinder Kits. Use with A-69225 Screw-Lok Mandrel or 1/4″
4 A-3604*
120
shank A-M36 Mandrel for use in handpieces, see pg 20.
5 A-3606
240
*A-3602 and *A-3604 come in Angle Grinder Kits
6 A-3607
320
7 A-3608
400
8 A-3609
600
Assortment, 16-Pc– All Grits:
AK3600 $15.20 2 ea of discs above
Assortment, 8-Pc– Coarse Grit:
AK3610 $7.90 2 ea of 24, 40, 80
& 120 grit discs
Assortment, 8-Pc– Fine Grit:
AK3620 $7.90 2 ea of 240, 320,
1 2 3 4 5 678 400 & 600 grit discs
A-69212L Long Hub comes in
Angle Grinder Kits. See Page 20.
Part Numbers and Prices shown in red on each page.
2″ Aluminum Oxide Sandpaper Discs 2″ Felt Wheels with Screw-Lok Backing and Wheels with 3/8” Arbor Holes
10,000 RPM Max Speed for A-3402 and 20,000 RPM for A-KE6 and ARFWAGSE
Medium Hard Screw-Lok Backed Felt Wheel A-3402 has a softer edge that provides a flexible surface for
contours. Use with new A-69225 Screw-Lok Mandrel. Hard Density Felt Wheels A-KE6 and ARFWAGSE
with 3/8″ Arbor Holes are made from tightly compressed felt. They hold an edge for working in angles
and corners. They mount to the Angle Grinder with the A-69212L Long Hub. All three wheels are made
from top quality wool and used with polishing compounds for polishing and lapping on metals, plastics,
wood and other materials.
Knife Edge Felt Wheel
Felt Wheel with
Screw-Lok Backing
3/4″ Thick Felt Wheel
Wheels
with
Arbor
Holes. Not
Screw-Lok
1
Felt Wheels:
Part No.
Price Thick″/ Type
1 A-3402 $2.10 5/16
Medium
2 A-KE6$5.80
Knife Edge Hard
3 ARFWAGSE $15.50
3/4
Hard
1-7/8″ dia, 1/2″ from arbor hole to edge
2
3
A-69212L Long Hub
comes in Angle Grinder
Kits. See Page 20.
FOREDOM®
29
Angle Grinder Accessories– Discs and Kits
Radial Bristle Discs can also be used with Mandrels in Flexible Shaft Handpieces and special Adapters for use with BL Bench Lathe, see page 18.
2″ Scotch-Brite™ Radial Bristle Discs
with 3/8” Arbor Holes $22.90 per 6-Pk
3M Scotch-Brite Radial Bristle Discs are molded plastic discs embedded with 3M Cubitron™ and aluminum oxide mineral. The abrasive filled
bristles apply a continuous supply of fresh mineral eliminating the need for compounds. Their flexible bristles reach into grooves and contours.
Varying the speed allows you to obtain different finishes. Mount 1-2 discs on Short Hub and 3-4 on Long Hub.
Mount with A-69212
Short and A-69212L
Long Hubs. See Pg 20
1
2 3456 7
2″ Scotch-Brite Roloc
End Brushes– 3 Grits
$16.30 Ea
NEW
Mount with A-69225 Screw-Lok
Mandrel. See page 20.
Assortment Kits
See individual accessory listings
for Maximum Speed
AK6903 $105
Woodcarving Kit, 60-Pc
Typhoon Carbide Disc A-KB25628, CeramCut
Blue Wheel A-10064, Scotch-Brite Radial Bristle 80-Grit Discs A-4542-6, 5 ea of Aluminum
Oxide Sanding Discs A-5632-5, A-5633-5,
A-5634-5, A-5635-5, Abranet Sanding Screen
Kit AK10030, 25 PSA Velcro Discs A-10041,
2 Disc Protector Pads A-10042. Radial Bristle
Discs, 6-Pk
Grit
Color
A-4542-680yellow
A-4543-6 120white
A-4544-6 220red
A-4545-6 400blue
A-4546-6 Pumice
pink
1,200
6 A-4547-6 6 Micron peach
3,000
7 A-4548-6 1 Micron lt. green
14,000
1
2
3
4
5
Roloc End Brush Grit
Color
1 A-450436green
2 A-4505
80yellow
3 A-4506
120white
AK6905 $78
Metal Working Kit, 73-Pc
Square Edge Felt Buff ARFWAGSE, Silicon Carbide Wheel
A-10068, Aluminum Oxide Wheel A-10063, Abranet Sanding Screen Kit AK10030, 2 Disc Protector Pads A-10042,
1-oz Platinum White Polishing Compound A-40061, 5 ea of
Imperial Microfinishing Discs A-4591, A-4592, A-4593,
A-4594, A-4596, A-4598, 2 Cut Off Wheels A-D11,
30 PSA Velcro Discs A-10041. 1″ & 2″ Quick Change Sanding Discs–
AK6901 $68
Stone Carving Kit, 20-Pc
Flexible Diamond Disc A-5752,
Diamond Microfinishing Discs
A-4452, A-4453, A-4454, A-4455,
A-4456, A-4457, A-4583. 2 Cerium
Oxide Discs A-4408, 10 PSA Velcro
Discs A-10041. 10,000 RPM Max Speed
1″ $3.70/10-Pk 2″ $5.50/10-Pk
Quick Change Sanding Discs are made of economical aluminum oxide grain and have a slotted, hard plastic backing. The 2″ size disc overhangs
the plastic backing and offers excellent flexibility for sanding contours. This style disc REQUIRES the use of a A-69223 Quick Change Arbor with
Cross Bar that mounts onto the Angle Grinder. Once the arbor is installed, it is quick and easy to make grit changes. 10Pks of 1″ and 2″ diameters
Discs come in 5 different grits.
1″ Part No. 2″ Part No.
Mount with A-69223
10-Pk 10-PkGrit
Quick Change Arbor
A-2241-10 A-2261-10 60
Quick Change Arbor with Cross Bar.
with Cross Bar.
A-2242-10 A-2262-10 120
See Page 20
A-2243-10 A-2263-10 240
A-2244-10 A-2264-10 320
Slotted
A-2245-10 A-2265-10 600
5 Grits
1″ Assort. AK2240 $3.70 2 ea of 5 grits
Disc Back
2″ Assort. AK2260 $5.50 2 ea of 5 grits
A-69223 $5.00
30
FOREDOM®
Angle Grinder Accessories– 2″ Sanding & Foam
Heads and PSA Discs
Mounting Pressure Sensitive Adhesive (PSA) Sanding Discs
1. (Non Screw-Lok): Use A-10041 PSA Disc with Velcro®
Loop surface to adhere PSA 2″ sanding discs to the
Velcro® Hook surface of A-69222 Disc Mandrel OR the Velcro® Hook surface of Sanding Heads 1, 2, 3, and 4 shown
below. PSA Velcro® Disc A-10041 insulates, prevents slippage, and permits reuse of sanding discs.
2. (Screw-Lok Velcro Surface Disc): Use A-3705 and
A-3702 Discs with Velcro Hook Fronts and Screw-Lok
backs along with A-10041 Velcro Loop Discs to attach
PSA 2″ discs to A-69225 Screw-Lok Mandrel.
3. (Screw-Lok Plain Surface Disc): Use A-3704 Discs
have plain front and Screw-Lok backs to attach PSA 2″
discs to directly to A-69225 Screw-Lok Mandrel.
See page 20 for listing of A-3705, A-3702 and A-3704
Velcro®
Hook
Surface
A-69222
Disc Mandrel
A-10041
Velcro®
Loop Disc
with sticky
side on
reverse
Velcro® Hook Disc Mandrel
Screws onto Angle Grinder:
A-69222 Ea $6.30
PSA Velcro® Loop Discs
with sticky side on reverse:
A-10041-5 (5-Pk) $4.40
NEW
A-69225A-3705
A-3705
Screw-Lok Velcro Hook
Screw-Lok
Mandrel
Disc FRONT
Disc BACK
2″ Velcro® Sanding & Foam Heads
Sanding Heads can vary the firmness or softness of the pressure applied from an abrasive disc. Use A-10041
PSA Velcro Loop Discs to attach actual abrasive discs to Velcro Hook Sanding Heads 1, 2, 3 and 4 that have
3/8″ arbor holes for mounting onto Angle Grinder with A-69212L Long Hub. Heads can also be used with
A-10042 Disc Holder Protector Pad and Sanding Screens, shown on page 32.
Velcro Foam Heads 5 & 6 attach to A-3705 Discs with Velcro Hook fronts and Screw-Lok backs and then
mount onto Angle Grinder with A-69225 Screw-Lok Mandrel. You can also attach Heads 5 & 6 directly onto
A-69222 Velcro Hook Surface Mandrel.
Sanding & Foam Heads Priced at Right
4
2
Foam Heads 5 & 6 have Velcro
Hook on one side and loop on
the other
1, 2, 3 and 4 have
Velcro Hook Surfaces
1
3
Screw-Lok Mandrel Screws
onto Angle Grinder:
A-69225 Ea $5.25
Velcro® Hook Discs
with Screw-Lok back:
A-3705 $1.70
5
6
Also for use with Screw Mandrels A-M-30 and A-M31 on page 18
2″ Ceramic Purple PSA
Sanding Discs $1.30 Ea
Photo courtesy www.jadecarver.com
A-10046 Sanding Head with PSA
Flex Diamond disc on California Jade.
Sanding & Foam Heads Price Ea
1 A-10043$11.00 Extra Firm, 3/16″ thick
2 A-10044$11.55
Firm, 5/16″ thick
3 A-10045$12.10
Medium, 3/8″ thick
4 A-10046$13.10
Soft, 5/8″ thick
5 A-10047$2.20
Soft, 1/4″ thick
6 A-10048$2.20
Soft, 1/2″ thick
Individual
$1.30 Ea
Part No.
Grit
A-5682 60
10-Pk
$8.40/10-Pk
Part No.
Grit
A-5632-10
60
A-5633-10
A-5634-10
120
A-5635-10
220
Assortment AK5630 $6.80 2 ea of 4 grits
3M Ceramic Purple Abrasives are excellent for sanding and
finishing wood, metals, fiberglass, diestone, plastics, and
A-5683 80
4 Grits
other materials. Its patented CubitronTM ceramic aluminum
A-5684 120
oxide mineral sharpens itself with use. Ceramic Purple discs
A-5685 220
last 2 to 4 times longer than traditional aluminum oxide
Assort. AK5680 $4.70 and offer faster stock removal with less heat and load1 ea of 4 grits
ing. Other sizes of discs and bands are available for use in
handpieces, see page 10.
Mount with A-10041 PSA Velcro Loop Disc & A-69222 Velcro Hook
Disc Mandrel or Velcro Hook Sanding Head
2″ Aluminum Oxide PSA
Sanding Discs $8.40/10-Pk
3M Aluminum oxide sanding discs are made of high-grade
mineral and a bonding system which reduces shelling of the
mineral. These economical abrasives are excellent for fast
clean-up and pre-polishing work. Several sizes of bands are
also available for use in handpieces, see page 11.
4 Grits
FOREDOM®
80
31
Angle Grinder Accessories– 2″ PSA Sanding Discs
Mount with A-10041 PSA Velcro® Loop Disc & A-69222 Velcro Hook Disc Mandrel or Velcro Hook Sanding Head. See Pages 20 and 31
2″ Flexible Diamond
3M Flexible Diamond PSA discs are made from a 2-ply polyester backing
film evenly coated with diamond filled nickel plated dots. Grind, sand,
and smooth wet or dry on glass, carbide, composites, plastic, enamels,
stone, steel, exotic alloys, gypsum, ceramics, wood, bone, chrome cobalt,
painted or plated surfaces. Use wet when working with gemstone, rock
and glass. Bands also available for use in handpieces, see page 8.
5 Grits
2″ Diamond Microfinishing Film
PartPrice
No. Each
Grit Micron
A-5752 $17.30
60250
A-5753 $13.90
120
125
A-5754 $11.80
220
74
A-5756 $9.70
400
40
A-5758 $9.7080020
5-Pc–Assort, 1 ea grit: AK5750 $57.75
PartPrice
3M’s Diamond Microfinishing PSA discs, in six color coded micron grades from 125 to 9, have flexible
No. Each
Grit Micron
film backing suitable for metal and lapidary applications. They work great on all materials including
stone, glass and hard to work on stainless steel and titanium. Use wet when working with gemstone,
A-4452 $4.70
120124
rock and glass. Bands and a smaller disc also available for use in handpieces, see page 9.
A-4453 $4.60
220
74
A-4454 $4.60
320
45
A-4455 $4.60
400
30
A-4456 $4.60
600
20
A-4457 $4.60 1,200
9
A-4583 $8.20 4,000
3
7-Pc Assort, 1 ea grit: AK4450 $33.60
16-Pc Assort, 1 ea grit, A-10040 Velcro
Hook, A-10041 (8) Velcro Loop:
AK4400 $47.25
2″ Imperial Microfinishing Film
2″ Cerium Oxide Polishing Disc
A-4408 $5.90 Ea 50,000 Grit, .5 Micron
Use 3M Cerium Oxide for achieving a final, high shine polish on
gemstone, rock and glass. Disc should be used wet and results are
also best when used after a 1,200–4,000 grit abrasive. See pages
8 and 9 for other discs & bands for use in handpieces.
2″ Abranet™ Sanding Screens
with Velcro Loop Backing
$6.40/5-Pk
A-10042 Disc Holder
Protector Pad &
A-69222 Disc Mandrel
Screens
in 5 Grits
Great
on Glass
and Stone
Use 3M Imperial Microfinishing PSA
discs dry on metal and wet on stone.
High strength polyester film backing,
coated with premium, micron graded
aluminum oxide particles, provides
greater cutting efficiency and is resin
bonded for increased durability. This
fast-cutting abrasive provides gentle,
contoured polishing.
Aluminum oxide grain abrasive coating bonded to unique,
durable, open construction polyamide fabric for uniform
sanding. Screens have Velcro Loop backing and MUST be
Protector Pad on Velcro
Abranet Screens
used with A-10042 Disc Holder
5-Pk
Hook Disc Mandrel A-69222 or
with Velcro Hook Sanding
to clean dust from sanding. Part No.
Grit
Heads. Tap or blow screens out
wood.
A-10032-5 80 Will not clog, even on wet or green
A-10042 $3.40 Ea
Disc Holder Protector Pads:
Made in USA.
a secure connection
Orange-colored velcro pad forms
between the Abranet sanding screen
and the disc mandrel.
It prevents overheating & clogging.
U
sing one for each grit
is recommended to prolong the life of the Abranet Screens.
Screen back and white side
Use orange side on the Abranet
for Velcro Hook Disc Mandrel or Velcro Hook Sanding Head.
32
A-4408
Part
Price Per
No. 10-Pk
Grit Micron
A-4591-10 $5.90 1,2009
A-4592-10 $5.90
60015
A-4593-10 $5.90
40030
A-4594-10 $5.90
32040
A-4596-10 $5.90
22060
A-4598-10 $5.90 180
80
FOREDOM®
A-10033-5 120
A-10034-5 180 A-10035-5 240
A-10036-5 320
Assort 5-Pc
AK10030 $6.40 1 ea grit
M.BL Bench Lathe Accessories
EVE Wheels Made in Germany, all other BL Accessories shown here
Unmounted 2-1/2″ EVE Wheels, 3/8″ thick with 1/4″ Arbor Holes. Use
on Lathe with A-WM-5 & A-WM-6 Wheel Mandrels
2-1/2″ Silicone Wheels make short work of larger finishing jobs for jewelers and metal smiths.
Wheels can be used on the face or its side for lapping and can be contoured to any shape with
the use of a dressing stone or diamond file. They create very little dust and are long lasting
when used properly. Note: While wearing safety glasses, wheels can be contoured with steps,
channels, and half round grooves to help prep any large piece for polishing. However care
should be used not to crack, tear, or break the silicone wheels.
Exclusive to Foredom 2-1/2″ EVE Wheels $18.90 Ea
1 2 3456
1, 2 & 3 Universal Silicone Wheels
are good for smoothing, grinding
and preparing larger cast pieces for
a final polish. Use on ferrous & nonferrous metals.
4 & 5 Platinum Wheels for
Platinum, Stainless Steel & ChromeCobalt offer a less aggressive approach for finishing hard metals.
7
6 & 7 Pumice Wheels for finishing metals already set with natural
and man-made gemstones.
1
2
3
4
5
6
7
Part No. A-5541 Application Universal
Grit
Coarse
A-5542 Universal
Medium
A-5543 Universal
Fine
A-5545 Platinum
Medium
A-5546 Platinum
A-5547 A-5548 Pumice
Pumice
Fine
Medium
Fine
Unmounted 3″ Satin Finisher Double Ply Wheels with Canvas Reinforced Arbor Holes. Use on Tapered
Spindles of Lathe $6.80 Ea Can also mount onto A-M89 Mandrel for use in Flexible Shaft Handpieces, see page 18.
Scotch-Brite Satin Finisher Wheels give metal a soft, medium, or coarse finish. All grades are handy at removing firescale from sterling silver and
copper and can also be used to prepare pieces for polishing. Wheels perform well around all types of contoured surfaces and give a uniform finish. They stay together better than traditional satin finishers therefore creating less dust and particles in the air.
Unmounted 3″ EXL Wheels. Use on Tapered Spindles or with A-WM-5 & A-WM-6 Wheel Mandrels $22.60 Ea
EXL Wheels with aluminum oxide grain run cool and should always be used dry. Medium dense A-5587 is best for decorative finishing since it
confirms to contour surfaces and harder A-5588 is better for more difficult blending, surface cleaning and deburring.
1
2
3
4
5
6
EXL Wheels
1
2
3
4
5
6
Part No. A-5534 A-5535 A-5536 A-5537 A-5587 A-5588 Grit
Hardness
Extra Fine N/A
Fine
N/A
Medium
N/A
CoarseN/A
Medium
Medium
Coarse
Hard
Unmounted 2″ Abrasive Wheels with 1/4″ Arbor Holes for use on BL Bench Lathe with A-WM-5 & A-WM-6
Wheel Mandrels Use 1, 2, 3 and 7 on any metal. Use 6 for smeary metals like
$5 Ea Except A-10078 is $6.80 Ea
aluminum and pewter. 4 & 5 are for ferrous alloys.
1*
1-3/4″
2
3*
1-7/8″
4
5
6
7
Unmounted Cotton and Felt Buffs. Use
on Tapered Spindles of BL Bench Lathe
Cotton Buff A-CB1 can also be used on a flex shaft
handpiece with mandrels A-M78 or NEW A-M89.
Felt Buff A-W305 can mount on a handpiece with
mandrels A-M8 or A-M85. See mandrels on page 18.
1
2
3
4
5
6
7
Part No. Material Dia. Thick Grit
A-10072 Aluminum Oxide 1-3/4 3/860
A-10074 CeramCut Blue
2
1/4120
A-10073 Aluminum Oxide 1-7/8 1/4400
A-10075 Salt & Pepper
2
1/446
A-10077 Silicon Carbide
2
1/4100
A-10078 Silicon Carbide
A-10076 V Stone
2
2
1/4100
1/446
Part No. Material
Dia. Thick Hole
1 A-CB1 Cotton, 16 ply 2-1/2 1/2Pin
2 A-W305 Felt
2
3/81/4
1
2
A-CB1 $3.20 A-W305 $4.20
FOREDOM®
33
Chisels for Foredom H.50 & H.50C Handpieces and
other Reciprocating Power Chisels Max: 10,000 Strokes per Minute
These pre-sharpened, quality made steel chisels are for use in Foredom’s H.50 reciprocating chisel handpiece and other power chisel tools, including those from Proxxon and WeCheer. The cutters have 18mm long tangs and 55mm and 75mm overall lengths–from cutting edge to end of tang.
Cutters in the A-KC500 Series are 55mm and those in the A-KC700 series are 75mm long. Priced individually and in sets below.
#1 Chisels
Single Bevel
18º to 20º Sharpening Angle
#2 Right Skews
Single Bevel
Fluteroni
#3 and #7 Sweeps
#1 x 9mm #1 x 14.5mm
#2 x 9mm #2 x 14mm
8mm
12mm #3 x 9mm #3 x 14mm #7 x 8mm #7 x 13mm #7 x 17mm
A-KC509A-KC511 A-KC510A-KC512 A-KC515
A-KC721
A-KC503A-KC501A-KC504A-KC502A-KC718
$7.50$9.50 $7.50$9.50 $9.50
$10.50
$7.50$9.50$7.50$9.50$10.50
5555 5555 55
75
5555555575
1, 3
2, 3
1, 3
4
3, 4
5
1, 3
2, 3
1, 3
2, 3
5
Comes in Sets
Part No. Price Each Length mm ;
;
18º Sharpening Angle
17º
20º
25º
#8, 9, 11 Sweeps
#8 x 10mm #9 x 9mm
#9 x 6mm
20º
17º
20º
18º
15º
70º, 75º, 110º Parting Tools
#9 x 14mm #11 x 3.5mm 70º x 5.5mm 70º x 8mm 75º x 12mm 110º x 7mm 110º x 11mm 110º x 16mm
Part No. A-KC508 A-KC514A-KC517 A-KC723 A-KC505 A-KC506A-KC507 A-KC717 A-KC516 A-KC513 A-KC722
Price Each $9.50$9.50$7.50 $10.50$7.50 $7.50$9.50$10.50$7.50 $9.50$10.50
Length mm 55
5555 7555 555575555575
Comes in Sets
2, 3
4
4
5
1, 3
1, 3
2, 3
5
4
4
5
Chisel Sets
Sets 1, 2, 4, and 5 come packed in
hanging plastic case. Set 3 comes in
A-KC500 canvas pouch.
AKHK550 6-Pc $41
A-KC503, A-KC504, A-KC505, A-KC506,
A-KC509, A-KC510
Set 2 AKHK560 5-Pc $41
A-KC501, A-KC502, A-KC507, A-KC508,
A-KC511
Set 3
AK510 12-Pc $79
A-KC501, A-KC502, A-KC503, A-KC504,
A-KC505, A-KC506, A-KC507, A-KC508,
A-KC509, A-KC510, A-KC511, A-KC515
in A-KC500 Canvas Pouch
Set 4
AKHK570 6-Pc $47
A-KC512, A-KC513, A-KC514, A-KC515,
A-KC516, A-KC517
NEW
″
4-1⁄8
Dimensions shown in mm
2″
3
3
Set 1 ⁄2″
7-1
⁄4″
6-1
A-KC500 $21 Empty Canvas Pouch
12-Pc Chisel Set (AK510) comes packed
in canvas pouch shown above. Includes
chisels in Set 3.
A-KC717, A-KC718, A-KC721, A-KC722,
A-KC723
Typical
dimensions
for cutters
in sets
AKHK550,
AKHK560,
AK510,
and
AKHK570.
FOREDOM®
Set 5
34
AKHK580 5-Pc $47
Open Canvas Pouch measurements:
7-1/2″ x 6-1/4″. Folds to 2″ x 4-1⁄8″.
Typical dimensions for larger
cutters in Set 5
AKHK580.
Frank Stetson, Connecticut relief woodcarver, uses our Chisels.
Hammer Handpiece Accessories Made in USA. 0-5,000 Strokes per Minute Max Speed
These six threaded anvil points fit Foredom Flex Shaft Hammer Handpieces, Foredom
Micromotor Hammer Handpiece and the Swiss made Badeco Hammer Handpiece. They
are heat treated steel made to the finest specifications and finished with black oxide.
AK101 $75
6-Pc Kit Anvil Points
Includes Ball Nose, Fine Point, Square,
Cylinder, Rectangle and Bezel Rocker.
Points shown at left.
HP10171 $9 Ball Nose 3/32″ (2.35mm) dia.
HP10172$9
Fine Point .015″ (.4mm) dia. Carbide Stylus
HP10212 $38
4-48UNF-2A thread
HP10173$12
Square 3/32″ (2.35mm)
HP10215 $38 Non-threaded
Other Hammer Tips
H.15, H.15D, H.15SJ
Handpieces
H.9D PowerGraver
Handpiece
Diamond Tip Pavé Point HP10175$12
Cylinder 7/32″ (6mm) dia.
A-R15PT$38 4-48UNF-2A thread
H.15, H.15D, H.15SJ Handpieces
HP10176$12 Rectangle 3/32″ x 3/16″ (2.35mm x 4.8mm)
Flat Top Taper
HP10177$6 4-48UNF-2A thread
H.15, H.15D, H.15SJ
Handpieces
HP10179 $29 Bezel Rocker 5/16″ x 1/16″ (8mm x 1.6mm)
HP10177K$6 M3 X 0.5 thread
Micromotor Hammer
HP10177P$6 Non-threaded
H.9D PowerGraver
MPMH-011 Handpiece
Handpiece
Foredom Filer Accessories Maximum Input Motor Speed of 10,000 RPM (or 4,000 SPM)
Diamond Needle
File Sets
45mm
$47.20 Ea
5-Pc Sets in 3 Grits
AK891012NF 150 grit
AK891020NF 200 grit
AK891040NF 400 grit
90mm
EDM Abrasive Stones, 120, 220, 400 Grit
12mm wide x 3mm thick x 67mm long
1/2″ wide x 1/8″ thick x 2-5/8″ long
Hard aluminum oxide stones especially developed for the polishing of EDM machined
surfaces. Stones break down slowly and retain shape. Excellent for hard steel tools.
A-894120 $1.90 120 grit
Super Stones Rods and Bars
Super Stones produce uniform surface finishes and
come in color coded grits.
Long lasting, heat and wear
resistant with ceramic fibers
that will not break or dull.
They are great for polishing
narrow slots, interior and
intricate spaces on all types
of metals including gold,
platinum, stainless, copper,
aluminum, and even silicon
and plastics. Must be used
with Abrasive Tool Holder.
Super Stone
Bars $10.00 ea
Super Stone Rods
$18.40 ea
3mm dia. x 50mm long
A-SSR12003 1,200 grit
A-SSR10003 1,000 grit
A-SSR8003
800 grit
A-SSR6003
600 grit
A-SSR4003
400 grit
A-SSR3003
300 grit
A-SSR1803
180 grit
A-SSR1203
120 grit
0.5mm thick x 1mm wide x
100mm long
A-SSF120012 1,200 grit
A-894220 $1.90 220 grit
A-SSF100012 1,000 grit
A-894400 $2.40 400 grit
A-SSF80012 800 grit
AK894000 $10.50 6-Pc Set: 2 of ea Grit
A-SSF60012 600 grit Always Wear Eye and Dust Protection While Using Rotary Power Tools and Accessories
FOREDOM®
35
Our mission is to offer the best quality and selection of accessories for accomplishing what you do best—
whether you’re a jeweler, woodcarver, machine shop operator, custom manufacturer, fabricator, research
scientist, lab technician, conservator, display designer, sculptor, artisan, crafter or home shop enthusiast.
Our catalog features what you expect from Foredom– a vast selection of items in different sizes, shapes
and grits. Since quality is key, the majority of our accessories are made in the USA, and nearly all of the
rest come from Switzerland, Germany, and Belgium.
Product Index
New Items Shown in Red
Page
Page
Page
Abrasive Cleaner. . . . . . . . . . . . . . . . . . . . . . . . . 26
CeramCut Blue Stones and Wheels. . . . . 3-4, 28, 33
Abrasive Discs and Cut Off Wheels. . . . . . . . . . . 12
Ceramic Purple Sanding Bands & Discs. . . . . . 10, 31
Respirator, 3M. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Aluminum Oxide Grinding Wheel . . . . . . . . . 28, 33
Cerium Oxide Polishing Disc, 3M. . . . . . . . . . . . . . 8
Rubber Bonded Abrasive Wheels . . . . . . . . . . . . 12
Aluminum Oxide Mounted Points . . . . . . . . . . . . . 5
Chisels, Cutters . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Rubber Drum Mandrels . . . . . . . . . . . . . . . . . . . . 19
Aluminum Oxide Sanding Bands & Discs, 3M .11, 31
Cobalt Steel Step, Twist, Pilot Drills. . . . . . . . . 22-23
Rubber Sanding Disc Mandrels . . . . . . . . . . . . . . 20
Aluminum Oxide Sanding Flap Wheels. . . . . 11, 28
Collet Adapters– 'Step Down' Sleeves. . . . . . . . . 19
Ruby Carvers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Angle Grinder Accessories– 2″. . . . . . . . . 28-32
Compounds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Safety Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Abranet™ Sanding Discs. . . . . . . . . . . . . . . . . . . . 32
Cotton Buffs, Unmounted . . . . . . . . . . . . . . . . 17, 33
Safety Glasses. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Abrasive Pads–Screw-Lok . . . . . . . . . . . . . . . . . . 29
Abrasive Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Aluminum Oxide PSA Sanding Discs. . . . . . . . . . . 31
Aluminum Oxide Sanding Flap Wheels. . . . . . . . . 28
Aluminum Oxide Sandpaper Discs–Screw-Lok . . . 29
Arbors, Hubs, Mandrels for Mounting Accessories. 20
Assortment Kits. . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Ceramic Purple PSA Sanding Discs. . . . . . . . . . . . 31
Diamond Microfinishing Film PSA Sanding Discs. 32
Felt Wheels–Screw-Lok & Non-Screw-Lok . . . . . . 29
Fiberglass Cut Off Wheel. . . . . . . . . . . . . . . . . . . . 28
Flexible Diamond PSA Sanding Discs . . . . . . . . . . 32
Scotch-BriteTM Radial Bristle Discs, 3M. . . . . . . . . 30
Scotch-BriteTM Roloc End Brushes, 3M. . . . . . . . . . 30
Screw-Lok Discs . . . . . . . . . . . . . . . . . . . . . . . 20, 31
Quick Change Sanding Discs– 1″ & 2″ . . . . . . . . 30
Typhoon® Tungsten Carbide Discs. . . . . . . . . . . . . 28
Velcro® Foam Sanding Heads. . . . . . . . . . . . . . . . 31
Cut-Off Wheels, Unmounted . . . . . . . . . . . . . 12, 28
Sandpaper Belts for Belt Sander Attachment. . . . 11
CW Polishing Wheels, Unmounted . . . . . . . . . . . 12
Satin Finishers. . . . . . . . . . . . . . . . . . . . . . . . 13, 33
Diamond Chamfer Mounted Points– Plated . . . . . 7
Scotch-Brite™ Radial Bristle Discs, 3M . . . 14-15, 30
Diamond Cutting Discs– Plated. . . . . . . . . . . . . . . 7
Scotch-Brite™ Roloc End Brushes, 3M. . . . . . . . . 30
Diamond Hones. . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Screwdriver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Anvil Points and other Hammer Tips. . . . . . . . . . 35
Filer Accessories . . . . . . . . . . . . . . . . . . . . . . . . 35
Typhoon® Tungsten Carbide Sanding Sleeves. . . 27
Assortment Kits. . . . . . . . . . . . . . . . . . . . . . . . . . 21
Diamond Needle File Sets . . . . . . . . . . . . . . . . . . . 35
BL Bench Lathe Unmounted Accessories. 18, 33
Radial Bristle Discs, 3M. . . . . . . . . . . . . . . 14-15, 30
Diamond Mounted Points– Plated. . . . . . . . . . . . . 6
Screw-Lok Mandrels . . . . . . . . . . . . . . . . . . . . . . 20
Diamond Microfinishing Film Bands & Discs, 3M .9
Silicon Carbide Unmounted Wheels. . . . . . . . 28, 33
Diamond Twist Drills . . . . . . . . . . . . . . . . . . . 22-23
Steel Carving Drills. . . . . . . . . . . . . . . . . . . . . . . . 22
Dressing Stone. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Steel Cutters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Drills. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23
Steel Fluted Engraving Burs. . . . . . . . . . . . . . . . . 24
DuraGrit® Carbide Accessories . . . . . . . . . . . . . . 23
Step Drills– Cobalt, Diamond Plated, Steel . . . . . 22
Dust Mask. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Tape, 3M Super Bond. . . . . . . . . . . . . . . . . . . . . . . 9
Ear Plugs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Trizact™ Sanding Bands & Discs, 3M. . . . . . . . . 10
Felt Bobs, Mounted. . . . . . . . . . . . . . . . . . . . . . . 16
Twist Drills– Cobalt, DIamond Plated . . . . . . 22-23
Felt Buffs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Typhoon® Tungsten Carbide Burs & Kits . . . . 26-28
Unitized, Non-Woven Mounted Points. . . . . . . . . 13
Vetrap Tape, 3M. . . . . . . . . . . . . . . . . . . . . . . . . . . 2
EDM Abrasive Stones . . . . . . . . . . . . . . . . . . . . . . 35
Super Stones, Bars & Rods . . . . . . . . . . . . . . . . . . 35
V Stones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Abrasive Wheels– 2″ . . . . . . . . . . . . . . . . . . . . . . 33
Adapters for Mounting Accessories . . . . . . . . . . . 18
Ceramic Purple PSA Discs. . . . . . . . . . . . . . . . . . . 10
Cotton & Felt Buffs, 2″ & 2-1/2″ . . . . . . . . . . . 17, 33
EVE Wheels– 2-1/2″ . . . . . . . . . . . . . . . . . . . . . . . 33
EXL Wheels– 3″ . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Kits– Polishing & Sanding . . . . . . . . . . . . . . . . . 20
Satin Finisher Wheels– 3″ . . . . . . . . . . . . . . . . . . . 33
Trizact Sanding Bands & 3″ Discs, 3M . . . . . . . . . 10
Cleaning Brush. . . . . . . . . . . . . . . . . . . . . . 26
Brass
High Speed Steel Fluted Burs. . . . . . . . . . . . . . . . 24
Brushes– Bristle, Steel, Brass, Wire, Nylon. . . . . . 13
Muslin Wheel. . . . . . . . . . . . . . . . . . . . . . . . . 13, 17
Buffs– Muslin, Cotton, Felt, Goblet. . . . . . . . . . . 17
Pilot Drills, Cobalt Steel. . . . . . . . . . . . . . . . . . . . . 22
Flap Wheels. . . . . . . . . . . . . . . . . . . . . . . . . . 11, 28
Flexible Diamond Sanding Bands & Discs, 3M. 8, 32
Hammer Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Latch Type Abrasive Points. . . . . . . . . . . . . . . . . . . 5
Mandrels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-20
Micro Chucks. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Miniature Carbide Burs. . . . . . . . . . . . . . . . . . . . 24
Velcro Hook PSA Discs. . . . . . . . . . . . . . . . . . 20, 31
Velcro Loop PSA Discs. . . . . . . . . . . . . . . . . . 20, 31
Velcro Sanding Heads . . . . . . . . . . . . . . . . . . . . . 31
Wet/Dry Polishing Papers, 3M. . . . . . . . . . . . . . . . 9
Wet Stick. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
FOREDOM
Foredom Electric Co.
Bur Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Plated Diamond Points, Mounted . . . . . . . . . . . 6-7
Carbide Burs . . . . . . . . . . . . . . . . . . . . . . . . . 23-27
Polishing Buffs. . . . . . . . . . . . . . . . . . . . . . . . . 17, 33
www.foredom.net
16 Stony Hill Road, Bethel, CT 06801
Tel: 203-792-8622 Fax: 203-796-7861
Carving Drills. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Polishing Compounds . . . . . . . . . . . . . . . . . . . . . 16
Email: customerservice@blackstoneind.com
Accessory Catalog 350G
Prices effective 7/1/15
Prices subject to change without notice.
FOREDOM®
®

Rotary Accessories

Transcription

Similar documents

Accessories for Hammer Handpieces