Accessories for Hammer Handpieces
Transcription
Safety Instructions Before using your Foredom® power tool with any of the accessories shown in this catalog, please read all safety instructions. They are for your protection and should always be followed to reduce the risk of personal injury or damage to the tool. Safety products, including glasses, ear plugs, and respirator, are shown below. It is Extremely Important to Follow these Instructions: • Always wear proper eye and face protection. Wear safety glasses or face shields whenever you operate a Foredom or any power tool to prevent serious eye or face injuries. • Always use a proper dust collection system or wear a respirator to prevent the inhalation of dust particles, polishing compounds, or other debris produced from abrasive accessories into the lungs. • Do not wear loose fitting clothing or jewelry. Loose clothing or jewelry can become entangled in the rotating accessory. Be sure to tie back or secure long hair. • Accessories in this catalog are rated for use at speeds indicated with a 1″ (25mm) overhang or less. Overhang is the distance from the front of collet or chuck jaw to the tip or point of the bur, mounted abrasive, or other rotary accessory. • Never operate any accessory at speeds above its maximum rated speed. Rotary accessories last longer and provide their best performance by applying gentle but firm pressure to the work piece and letting the speed of the motor do the work. • Pay close attention to the maximum speed listed for an accessory and never exceed this rating. Maximum speed is the highest speed at which an accessory can safely be run. If used at higher speeds, an accessory can fly apart, bend, or self destruct, resulting in possible serious injury to the operator or a bystander. • Extra care should be used with an accessory that has a lower max speed rating than the speed of the motor. When properly used, all of Foredom’s accessories can be operated at the speed ratings listed in this Catalog or on packaging. Always find out the manufacturer’s speed rating before using accessories other than those from Foredom. Part Numbers and Prices are shown in red on each page. Safety Products Made in USA AK6100 $24.60 Safety Kit Use this collection of safety products while running your Foredom or other power tool. Items come packed in plastic storage case. Includes: A-SG3 Safety Glasses A-6102 Roll of Vetrap tape A-6103-3 Foam Ear Plugs (3) A-6106-3 Respirators (3) A-6103-10 $6/10-Pk Soft Foam Ear Plugs Made of hypo-allergenic materials, these soft foam ear plugs have a tapered shape for a good fit and comfort. Plastic cord prevents tangling. Accessories for Hammer Handpieces 0-5,000 Strokes per Minute Max Speed Clear polycarbonate glasses with a contemporary style and unitary lens design. Temples are length adjustable with slotted ends. Includes black neck cord. Always Wear Eye Protection While Using Rotary Power Tool Accessories 2 Other Hammer Tips Carbide HP10212 $30.50 H.15, H.15D, Stylus H.15SJ 4-48UNF-2A thread HP10215 $30.50 H.9D PowerGraver Non-threaded Fine Point .015″ (.4mm) dia. HP10173$12 Square 3/32″ (2.35mm) Diamond Tip Pavé Point A-R15PT$29 H.15, H.15D, H.15SJ 4-48UNF-2A thread A-R15G$29 H.9D PowerGraver Non-threaded HP10175$12 Cylinder 7/32″ (6mm) dia. HP10176$12Rectangle 3/32″ x 3/16″ (2.35mm x 4.8mm) Flat Top HP10177$6 H.15, H.15D, H.15SJ Taper 4-48UNF-2A thread HP10177K$6 Micromotor Hammer M3 X 0.5 thread MPMH-011 HP10177P$6 H.9D PowerGraver Non-threaded HP10179 $29 Bezel Rocker 5/16″ x 1/16″ (8mm x 1.6mm) Part Numbers and Prices are shown in red on each page. Dress, Clean and Reshape with Diamond Hones, Dressing Stone, Wet Stick, Abrasive Cleaner, Brass Brush Made in USA Diamond Hones Dress and reshape mounted abrasive points by lightly touching a rotating point to the diamond surface. Also for hand smoothing and shaping glass, metal, stone, bone, and plastic. Use for sharpening chisels and steel instruments. 3/4″ x 2″ diamond pad on 6″ plastic color coded handle. A-6106-6 $15.80/6-Pk 3M Particulate Respirator 3-panel respirator with low profile design that folds flat and fits a wide range of face sizes. Comfortable, lightweight and convenient. Has Cool FlowTM Exhalation Valve for working in heat and humidity. A-4005 $2.60 Wet Stick Self-adhering tape is easy to apply and requires no pins, clips or adhesive to keep secure. Tape won’t loosen over time and stays in place until removed. Doesn’t stick to hair, skin, or anything else. Use to protect fingers during close work with sharp instruments. 2″ wide x 15′ long. Cover Photo Acknowledgements: Top left to right: Frank Russell uses a Typhoon Tungsten Carbide flame to aggressively shape a piece of wood. Katie Geerling uses a Plated Diamond wheel to make intricate cuts in eggshell. Mark Mann uses 1,200 grit Scotch-Brite Radial Bristle Discs mounted on Foredom's BL lathe to polish gold jewelry. Bottom left to right: Les Aldrich uses an Aluminum Oxide Grinding Stone to grind the edge of steel die plate. Frank Stetson uses a #11 sweep gouge chisel to relief carve in wood. Don Cyr uses an 2″ Unitzed Wheel mounted on Foredom's new Angle Grinder to polish a car wheel nock off. Includes Ball Nose, Fine Point, Square, Cylinder, Rectangle and Bezel Rocker. Points shown at left. HP10171 $9 Ball Nose 3/32″ (2.35mm) dia. A-6102 $4.10/Roll 3M Vetrap Tape A-SG3 $17.00 Safety Glasses AK101 $75 6-Pc Kit Anvil Points These six threaded anvil points fit Foredom Flex Shaft Hammer Handpieces, Foredom Micromotor Hammer Handpiece and the Swiss made Badeco Hammer Handpiece. They are heat treated steel made to the finest specifications and finished with black oxide. HP10172$9 Made in USA Use wet for unloading plated and sintered diamond points. 2″ x 1/2″ x 3/4″. Use to clean Typhoon burs, sanding sleeves and discs. It easily removes dust or chips from between rows of carbide points. Overall–5/8″ wide x 5-3/4″ long. Bristles–3/8″ wide x 1-3/4″ long x 5/8″ high. A-HB58 $4.10 Brass Brush Diamond Hone Grit Part No. Price Ea. Superfine (blue) 1200 A-10342 $8.80 Fine (red) 600 A-10343 8.80 Medium (purple) 400 A-10344 8.80 Coarse (black) 250 A-10345 16.60 A-AC1 $7.90 Abrasive Cleaner Removes material from around Typhoon points. Restores clogged sanding bands and discs, cartridge rolls, and other abrasives. Use it like a giant eraser by holding the accessory against the block while running to remove embedded grinding debris. 3″ x 3″ x 1-1/2″ A-10333 $7.80 Dressing Stone, 60 grit Silicon carbide block allows you to reshape mounted abrasives back to perfect concentricity by running in the groove comparable to head size. Cleans and exposes fresh abrasive particles. 3-3/8″ w x 1-1/4″ d x 1/2″ h. Always Wear Eye Protection While Using Rotary Power Tool Accessories 3 V Stones CeramCut Blue Stones Made in USA. 45,000 RPM Max Speed Made in USA. 45,000 RPM Max Speed Made with a vitrified, self-sharpening, special aluminum oxide grain with a super hard porous bond, V Stones are the coolest running and longest lasting abrasive stones. They easily cut hard metals like titanium, chromecobalt, nickel-cobalt, tool steel, and stainless steel, and softer metals such as lead, pewter, brass and aluminum with minimal smearing and loading. V Stones also work on ceramic tile, porcelain, wood, acrylic, glass, and marble. They can be used to shape, texture, and provide detail to carvings. Their larger head sizes and coarser grits make them more aggressive than our CeramCut Blue Stones. They are an economical alternative to plated and sintered diamond points. Mounts with A-WM5 or A-WM6 Wheel Mandrels New 3/32″ (2.35mm) Shank Mounted Points $3.40 Ea Part Numbers for 40/60 and 80 1/8″ (3.18mm) Shank Individual Mounted Points $2.50 Ea Part Numbers and Prices are shown in red on each page. Grit Shapes shown in Red on Separate Lines CeramCuts with * are in Kit AKHK28 shown below Shape Bud Ball Cylinder A-10076 $4.80 Ea 2″ V Stone Wheel for use with BL Lathe See Pg. 13. Tapered Wheel Flat Top Taper Grit A-V326 A-V336 A-V356 N/A N/A Part No. 40/60 Part No. 80 Grit A-V327A-V337 A-V357 A-V367 A-V397 Head Dia.″ (mm) 1/4 (6.4) 3/8 (9.5)1/4 (6.4) 1/2 (13)1/4 (6.4) Head Length″ (mm) 3/8 (9.5) 3/8 (9.5)1/2 (13) 3/16 (4.8)1/2 (13) Part Numbers and Prices are shown in red on each page. Large Medium Small Ball Nose Flame Small Ball Flat Taper Small Cylinder Shape A-CK8300 A-CK8301 A-CK8302 A-CK8318 A-CK8332 A-CK897*A-CK8144* Part No. 80 med 120 fine 80 med 80 med 120 fine 120 fine 120 fine Grit Head Dia.″ (mm) 1/4 (6.4)3/16 (4.8)1/8 (3.2)5/32 (3.9)1/8 (3.2)3/32 (2.35)1/8 (3.2) 1/2 (13)1/2 (13)1/2 (13)3/8 (9.5)1/8 (3.2)3/8 (9.5) 1/4 (6.4) Head Length″ (mm) 1/8″ (3.18mm) Shank Individual Mounted Points $2.80 Ea Wagner Dental Lab of Danbury, CT uses CeramCut Blue Stones for grinding chrome cobalt on flexible partial. CeramCuts with * are in Kit AKHK28 shown below V Stones vs. CeramCut Blue Stones: It’s not one or the other, these two superior products are complementary and effective when used together. CeramCut Blue Stones would follow the use of V Stones as their finer grits and smaller heads help in achieving detail and smoother finishes. Both abrasives are superior in performance and life to standard aluminum oxide or silicon carbide stones. They remove material faster, run cooler and last 3 to 5 times longer. Pear Large Ball Taper Wheel Shape Part No. A-CK8112A-CK890*A-CK852*A-CK8154 A-CK8175A-CK8132* A-CK846 A-CK8122* A-CK844* A-CK8182* 120 fine 80 med 120 fine 80 med 80 med 80 med 120 fine 120 fine 120 fine 120 fine Grit CeramCut Blue Stones Made in USA. 45,000 RPM Max Speed CeramCut Blue Stones are widely used on hard metals, including hardened and mild steel, steel alloys, chrome cobalt, titanium, New platinum, and other ferrous metals. They are also suitable for use on porcelain materials and wood. CeramCut Blue Stones maintain their shape and hold their cutting edge longer than any standard abrasive stones. They are non-impregnating and non-contaminating. Small Tapered Large Small RoundRound Shape Cylinder Wheel Flat Taper Top Taper 3/32″ (2.35mm) Shank Individual Mounted Points $2.50 Ea CeramCuts with * are in Kit AKHK29 on next page. Part No. A-CK352*A-CK360 A-CK390 A-CK392*A-CK396 A-CK398 Grit 120 fine 120 fine 120 fine 120 fine 120 fine 80 med Head Dia.″ (mm) 3/32 (2.35)1/2 (13)1/8 (3.2)3/32 (2.35)1/8 (3.2)1/8 (3.2) Head Length″ (mm) 1/4 (6.4)1/8 (3.2)1/2 (13)3/16 (4.8)1/2 (13)1/2 (13) Ball Nose Tree Long Medium Cylinder Cup Flame Head Dia.″ (mm) 3/8 (9.5)1/2 (13)3/8 (9.5)3/16 (4.8)3/8 (9.5)3/8 (9.5)1/8 (3.2) 3/8 (9.5)7/32 (5.5)1/2 (13) 1/2 (13)1/2 (13)3/4 (19)1/2 (13)3/8 (9.5)1/2 (13)5/16 (8.0) 3/8 (9.5) 3/8 (9.5) 1/8 (3.2) Head Length″ (mm) 3/32″ (2.35mm) Shank Kit, 9-Pc AKHK29 $21.50 1/8″ (3.18mm) Shank Kit, 8-Pc AKHK28 $19.40 A-CK300 Lg Ball Nose A-CK301 Med Ball Nose A-CK302 Sm Ball Nose A-CK318Flame A-CK322 Inverted Cone A-CK332Ball A-CK342 Tapered Cone A-CK352 Sm Cylinder A-CK392 Sm Flat Taper A-CK8122 Lg Ball A-CK8132 Cylinder Cup A-CK8144 Sm Cylinder A-CK8182Wheel A-CK844Taper A-CK852Tree A-CK890 Ball Nose A-CK897 Flat Taper Med Fine Fine Med Fine Fine Fine Fine Fine New 2″ CeramCut Wheels for Angle Grinder & BL Bench Lathe A-10064 $4.80 Large Medium Ball Nose Small Flame Inverted Cone Ball Tapered Cone Large Cylinder Shape A-CK300*A-CK301*A-CK302*A-CK318*A-CK322* A-CK375A-CK332*A-CK342*A-CK350 A-CK354 A-CK356 Part No. 80 med 120 fine 120 fine 80 med 120 fine 120 fine 120 fine 120 fine 120 fine 80 med 60 coarse Grit 1/4 (6.4)3/16 (4.8)1/8 (3.2)5/32 (3.9)1/8 (3.2)1/4 (6.4)1/8 (3.2)1/8 (3.2)1/4 (6.4)1/4 (6.4)1/4 (6.4) Head Dia.″ (mm) 1/2 (13)1/2 (13)1/2 (13)3/8 (9.5)1/8 (3.2)1/4 (6.4)1/8 (3.2)1/4 (6.4)1/2 (13)1/2(13)1/2 (13) Head Length″ (mm) Always Wear Eye Protection While Using Rotary Power Tool Accessories 4 2″ CeramCut Blue Wheel with 3/8″ arbor hole, 120 grit For use with Angle Grinder Attachment. See Page 26. Mount with A-69212L Long Hub Fine Med Fine Fine Fine Fine Med Fine A-10065 $8.50 A-10074 $4.80 2″ CeramCut Blue Cup Wheel with 3/8″ arbor hole, 100 grit. For use with Angle Grinder Attachment. See Page 26. 2″ CeramCut Blue Wheel with 1/4″ arbor hole, 120 grit. For use with M.BL Lathe. See Page 13. Mounts with A-WM5 or A-WM6 Wheel Mandrels Always Wear Eye Protection While Using Rotary Power Tool Accessories 5 Aluminum Oxide Mounted Points Made in USA. 35,000 RPM Max Speed Red Individual Points Red Aluminum Oxide mounted points are used for fast cutting on high tensile, tough materials such as steel and malleable iron. Also used on porcelain and glass. For medium to fine finishing work. Be sure to specify “Red” Part Nos. when ordering. CW Polishing Wheels $11.00/10-Pk AK150 $36.80 19-Pc Kit Red Mounted Points Foredom’s top of the line CW Ceramic Impregnated Polishing Wheels come in 6 different grits for smoothing and polishing precious metals including platinum, gold, silver, titanium, chrome cobalt, and all hard alloys. CW wheels are non-contaminating and work faster and last longer than other polishers. 3/32″ shanks 10-Pk Part No. White Individual Points White Aluminum Oxide mounted points of extremely fine grit (400) for a high finish on high tensile, tough materials including gemstone, stainless steel and glass. Extremely fine cutting. Points hold their geometry well. Be sure to specify “White” Part Nos. when ordering. 25,000 RPM Max Speed AK160 $36.80 19-Pc Kit White Mounted Points 3/32″ shanks 3/32″ (2.35mm) Shank Individual Mounted Points $2.20 Ea Part Numbers and Prices are shown in red on each page. Red Aluminum Oxide Part Nos. and Grits Jewelry Designs of Danbury, CT uses CW Wheels to polish flats on gold bangle bracelet. Specifications: 7/8″ Dia. x 1/8″ Thick (22 x 3.2mm) 1/16″ Center Holes Color Description Grit A-CW55810 White Super Fine 1,500 A-CW55710 Gray Extra Fine 1,000 A-CW55610 Orange Fine 500 A-CW55410 Violet Medium 320 A-CW55210 Green Med/Coarse 180 A-CW55110 Blue Coarse 120 A-CW55010 Assortment with 2 ea. Blue, Green, Violet, Orange and 1 ea. Gray and White. Rubber Bonded Abrasive Wheels $6.30/10-Pk Made in USA. 25,000 RPM Max Speed White Aluminum Oxide Part Nos. and Grits A-71A-72A-73 A-74 A-75A-76 A-78 A-79A-80 A-81 White Part No. Grit 400400400 400 400400 400 400400 400 A-A1 A-A1F-107/8″1/8″ Dark Green Fine 180 A-A1M-107/8″1/8″Black Medium 80-120 A-A1C-107/8″1/8″Brown Coarse 40-60 A-A2 A-A2F-105/8″3/32″ Dark Green Fine 180 A-A2M-105/8″3/32″Black Medium 80-120 A-A2C-105/8″3/32″Brown Coarse 40-60 A-A3 A-A3F-105/8″1/8″ Dark Green Fine 180 A-A3M-105/8″1/8″Black Medium 80-120 A-A3C-105/8″1/8″Brown Coarse 40-60 Head Dia.″ (mm) 1/8 (3.2)5/16 (7.9)1/4 (6.4)1/4 (6.4)1/4 (6.4)3/16 (4.8)1/2 (13)3/8 (9.5)5/32 (4.0)1/4 (6.4) 7/32 (5.6)1/32 (.79)11/32 (8.7)1/4 (6.4)1/2 (13)17/32 (13.5)1/16 (1.6)3/64 (1.2)7/32 (5.6)5/64 (2.0)Head Length″ (mm) Abrasive Discs and Cut Off Wheels Made in USA Rubber Bonded Discs A-D1 and A-D2 are suitable for grinding, smoothing, and cleaning glass, high speed steel, and other tough materials. Discs have 1/16″ (1.6mm) arbor holes. Fiberglass Reinforced Cut-Off Wheels A-D6, A-D8, A-D9 and A-D11are used to cut-off, groove, and trim metal, wood, and ceramics. New A-D11 is also for use with Foredom’s New Angle Grinder attachment for the H.30 Handpiece. Red Aluminum Oxide Part Nos. and Grits Red Part No. A-12 A-13A-15A-16A-17A-18A-19A-20 A-21 100 10012010012080 120150 100Grit White Aluminum Oxide Part Nos. and Grits 13/64 (5.2)5/32 (4.0)1/8 (3.2)5/64 (2.0)1/8 (3.2)1/4 (6.4)1/8 (3.2)3/16 (4.8)1/4 (6.4) 13/64 (5.2)1/4 (6.4)1/8 (3.2)17/64 (6.7)9/32 (7.1)9/32 (7.1)13/32 (10.3)5/32 (4.0)1/4 (6.4) Head Dia.″ (mm) Head Length″ (mm) Aluminum Oxide Grinding Stones with 1/16″ arbor holes $1.10 Ea Made in USA. 21,000 RPM Max Speed Aluminum Oxide Unmounted Stones used for grinding, cleaning, and smoothing very hard materials such as steel and malleable iron. Use with 3/32″ and 1/8″ shank Screw-Type Mandrels A-M1, A-M6, A-M13, A-M15, and A-M19 shown next page. Part No. A-G21 A-G22 A-G23 A-G33 A-G27 A-G28 Dia. 1/2″5/8″3/4″1/2″3/4″3/4″ Grit 120 120 100 80 80 80 Thick knife-edge knife-edge knife-edge 13/64″13/64″9/64″ Always Wear Eye Protection While Using Rotary Power Tool Accessories 6 Mandrels 3/32″ & 1/8″ Shanks Use A-M1 & A-M6 to mount 7/8″ dia. and smaller wheels with 1/16″ arbor holes. See page 19. Rubber Bonded Abrasive (silicon carbide) Unmounted Wheels are used for light deburring, cleaning, smoothing and polishing. Ideal for hard-to-reach areas on ferrous and non-ferrous alloys and other materials. Offers cushioned action performance. Available in Coarse, Medium and Fine. Color coded by grit. Sold in packs of 10. Wheels have 1/16″ Center Holes and should be used with A-M1 & A-M6 Mandrels. 10-Pk Part No. Dia Thick Color Description Grit Red Part No. A-1A-2A-3 A-4 A-5A-6 A-8 A-9A-10A-11 Grit 120120120 100 80 80 80 120120 120 White Part No. A-82 A-83A-85A-86A-87A-88A-89A-90 A-91 Grit 400 400400400400400400400 400 A-M1A-M6 1/16″1/16″ arborarbor holehole A-D1-5 New Fiberglass Cut Off Wheels Rubber Bonded Discs A-D2-5 A-D6 A-D8 A-D9 Part No. Dia Thick Grit Arbor Hole Max Speed Price A-D1-57/8″.023″90 1/16″ 30,000 RPM $ 1.20/ 5pk A-D2-51-1⁄4″.062″90 1/16″ 30,000 RPM 2.20/ 5pk A-D61-1⁄4″.050″60 1/16″ 40,000 RPM 1.50 Ea A-D81-1⁄2″.050″60 1/8″ 40,000 RPM 1.50 Ea A-D92″.050″60 1/8″ 40,000 RPM 1.60 Ea A-D11 2″.047″60 3/8″ 30,000 RPM 1.80 Ea AK122 $28.40 56-Pc Kit 6 each of A-A1, A-A2 and A-A3 in all 3 grits. Also A-M1 and A-M6 mandrels. A-M19 1/16″ arbor hole A-M13A-M14 1/16″ 1/8″ arbor arbor holehole Mandrels 1/8″ Shank Use A-M1, A-M6, A-M13 and A-M19 to mount Discs and Wheels up to 1-1/4″ dia. with 1/16″ arbor holes. Use A-M14 to mount wheels up to 1-1/2″ with 1/8″ arA-D11 bor holes. See pg. 19 For Use On/Recommended Mandrels Handpiece with A-M1 or A-M6 Handpiece with A-M13 or A-M19 Handpiece with A-M13 or A-M19 Handpiece with A-M14 Handpiece with A-M14 Handpiece with A-M31 or Angle Grinder with A-69212 Short Hub Always Wear Eye Protection While Using Rotary Power Tool Accessories 7 Dumont® Premium Plated and Sintered Diamond Points and Discs Made in Belgium 2.35mm (3/32″) Shank Mounted Plated Points Priced Below 120,000 RPM Max Speed New Premium quality Dumont Plated Diamond points have precision turned steel blanks to ensure proper concentricity and balance for high speed use. They feature consistent diamond coverage, a strong bond and tight dimensional tolerances. Dumont Diamonds are ideal for laboratory and other work requiring strict precision and adherence to tight tolerances. 125-180 micron natural diamond (80-100 grit). Unmounted A-DD1 has Dumont plating on both sides. 100 micron, 150 grit, Non Flex type disc. 20,000 RPM Max Speed BallBallBallBallBallBallBall Cutting Disc Shape A-PD3-1A-PD4-1A-PD24-1A-PD5-1A-PD30-1 A-PD31 A-PD40 A-DD1 Part No. 1.01.41.61.82.13.14.022 Head Dia. mm 1.01.11.41.61.83.03.9.45 Head Length/Thick mm $11$11$11$11$14$25$25$20 Price Each A-4005 $2.60 Wet Stick Use wet for unloading plated and sintered diamond points. 2″ x 1/2″ x 3/4″ 2.35mm (3/32″) Shank Mounted Sintered Points Priced Below 25,000 RPM Max Speed Premium quality Dumont Sintered Diamonds last 5 to 10 times longer than plated diamonds and up to 100 times longer than various types of silicon carbide or aluminum oxide mounted abrasives. They work with far less grinding dust and can be “re-sharpened” to expose new diamond particles as often as desired by slowly turning (@4,000 rpm/15 sec.) against a wet dressing stone (A-10333, pg. 3). Even new sintered points should be dressed for best results. Dumont sintered points come in a Hard Binder of 100 Micron/150 Grit for hard precious stones and metal finishing work (especially gold) when contamination of the surface prior to application of porcelain is a potential problem. Sintered Diamond Disc A-DS22 has a solid matrix of diamonds in a binder from edge to center. The cutting edge is always exposing new diamonds. 165 micron/80 grit Ball Martha’s Vineyard Glass Artist, Russell Carson, uses a sintered diamond for scrimshaw carving in glass. Taper Taper Taper Ball Nose Ball Nose Disc Shape Standard Plated Diamond Points $3.50 Ea 2.35mm (3/32″) Shank Mounted Plated Points Plated Diamond points are for use on hardened steel, glass, precious metals, ceram ics, stone, and composite materials in industrial, jewelry, and laboratory applications, and on hard and soft woods for carving, fine detailing, and texturing. They feature sharp, 125-180 micron natural diamond (80-120 grit) that is well balanced for high speed use in micromotor handpieces. Flame Flame Inv. Cone Inv. Cone Shape A-PD12 A-PD22 A-PD27 1.6 2.6 2.6 9.0 8.0 2.0 Part Numbers and Prices are shown in red on each page. Flexible Diamond bands and discs are made from a two-ply polyester backing film evenly coated with diamond filled nickel plated dots. Use wet or dry. Clean and unload with the A-AC1 Abrasive Cleaner on pg 3 or A-HB58 Brass Brush on pg 24. Bands in several grits come in 1/4″, 1/2″, and 3/4″ (6, 13 & 19mm) diameters for use with rubber drum mandrels with 3/32″ (2.35mm), 1/8″, 1/4″, 6mm shanks. 2″ discs (51mm) with PSA backs come in several grits for use on 2″ disc mandrels in flex shaft handpieces and Foredom’s new Angle Grinder. See pages 19-21 for complete mandrel listing. Use Flexible Diamond Bands and Discs to Grind, Sand, and Smooth on various materials: • glass • carbide • composite • plastic • enamels • stone • steel • exotic alloys • gypsum • ceramics • wood • bone • chrome cobalt • painted or plated surfaces Micron Grade Grit Individual Part No. Price Each Mandrels Max Speed (RPM’s) Flexible Diamond Bands Priced Ea 1/4″ D x 1/2″ L (6 x 13mm) For Use in Handpieces: 250 60 A-4812 $9.30 125 120 A-48135.80 A-SD324 74220 A-4814 5.80 A-SD184 40,000 40400 A-4817 5.80 20800 A-4818 5.80 Assortment AK4810 $28.60 (1 each of five grits) 1/2″ D x 1/2″ L (13 x 13mm) -DS712AA-DS753 A-DS756A A-DS758AA-DS742AA-DS746AA-DS22 Part No. A 3.13.13.1 2.71.65.022 Head Dia. mm 3.1 9.0 12.0 8.5 6.5 13.0 .5 Head Length/Thick mm $32$38$38 $32$32$46$49 Price Each 120,000 RPM Max Speed 3M Flexible Diamond Sanding Bands 1/2″ x 1″ band and Discs Made in USA A-PD7 Part No. Head Dia. mm 6.0 Head Length mm 4.8 1/2″ x 1/2″ band 2″ PSA Discs 3M Cerium Oxide Sanding Bands New and Discs Cerium Oxide Abrasives are used for achieving a final, high shine polish on gemstone, rock and glass. Bands and discs last longer when used wet. Results are also best when used following a 1,200 to 4,000 grit abrasive. Micron Grade Individual Part No. Price Each Mandrels Cerium Oxide Bands Priced Ea 250 60 A-4822 $8.80 For Use in Handpieces: 125120 A-4823 7.60 A-SD328 74220 A-4824 7.00 A-SD188 40,000 40400 A-4827 7.00 20800 A-4828 7.00 Assortment AK4820 $31.80 (1 each of five grits) 50,000 1/2″ D x 1″ L (13 x 25mm) Cerium Oxide Discs Priced Ea 25060A-4832 125120 A-4833 74220 A-4834 40400 A-4837 20 800 A-4838 $10.50 9.30 8.10 8.10 8.10 3/4″ D x 1-1/2″ L (19 x 38mm) 25060A-4842 $15.70 125120 A-4843 13.90 For Use in Handpieces: A-SD141 A-SD661 20,000 1/4″ D x 1/2″ L (6 x 13mm) 50,000 Flexible Diamond Discs Priced Ea A-4402 $1.80 1/2″ D x 1/2″ L (13 x 13mm) A-4404 $2.40 3/4″ (19mm) PSA 50,000 A-4406 $1.10 2″ (51mm) PSA 50,000 For Use in Handpieces: A-SD145 A-SD345 10,000 A-4408 $5.30 See pages 19-21 for complete mandrel listing. Ball Ball Ball BallBall BallBallBallCylinder Cylinder Cylinder TaperCone Wheel Shape A-PD3 A-PD4 A-PD24 A-PD5A-PD30A-PD25A-PD6A-PD26 A-PD2 A-PD9 A-PD10 A-PD15A-PD11 A-PD20 Part No. 1.0 1.4 1.6 1.8 2.1 2.6 3.3 4.3 1.2 2.3 4.0 2.6 2.1 5.8 Head Dia. mm .8 1.1 1.4 1.61.6 2.02.73.8 5.0 7.0 8.0 7.010.5 2.0 Head Length mm Always Wear Eye Protection While Using Rotary Power Tool Accessories 8 For Use in Handpieces: A-M33 A-M338 10,000 For Use in Angle Grinder: A-69222 with A-10041 10,000 For Use in Handpieces: A-SD324 A-SD184 40,000 A-SD328 A-SD188 40,000 For Use in Handpieces: A-M4 15,000 For Use in Handpieces: A-M33 A-M338 10,000 For Use in Angle Grinder: See below: 10,000 For Use in Angle Grinder See Page 29 2″ (51mm) PSA 250 60 A-5752 $22.70 125120 A-5753 19.30 74220 A-5754 16.40 40400 A-5756 16.40 20 800 A-5758 16.40 Max Speed (RPM’s) 2″ Flexible Diamond Discs 2″ Cerium Oxide Discs Attach with A-10041 PSA Velcro Loop Disc A-69222 Velco Hook Disc Mandrel Always Wear Eye Protection While Using Rotary Power Tool Accessories 9 3M Film Sanding Bands and PSA Discs Made in USA 3M Ceramic Purple Sanding Bands and Discs Made in USA Part Numbers and Prices are shown in red on each page. Diamond Microfinishing Bands and Discs Diamond Microfinishing abrasives have flexible film backing suitable for metal working and lapidary applications. They work great on all materials including stone, glass and hard to work on stainless steel and titanium. Use wet when working with gemstone, rock and glass. Bands in several grits come in 1/4″ and 1/2″ (6, 13mm) diameters for use with rubber drum mandrels with 3/32″ (2.35mm) & 1/8″ shanks. Discs in 3/4″ and 2″ (19 & 51mm) with PSA backs come in several grits for use on disc mandrels in flex shaft handpieces and Foredom’s new Angle Grinder. See pages 19-21 for complete mandrel listing. Micron Grade Grit Individual Part No. Price Each Mandrels Max Speed (RPM’s) Diamond Microfinishing Bands Priced Ea 1/4″ D x 1/2″ L (6 x 13mm) 125 120 74220 45320 30400 20800 9 1,200 For Use in Handpieces: A-4412 $4.20 A-4413 3.50 A-SD324 A-4414 3.20 A-SD184 40,000 A-4415 2.70 A-4416 2.50 A-4417 2.50 1/2″ D x 1/2″ L (13 x 13mm) 125 120 74220 45320 30400 20800 9 1,200 A-4422 $5.60 A-4423 4.80 A-4424 4.20 A-4425 3.50 A-4426 3.10 A-4427 3.10 For Use in Handpieces: A-SD328 A-SD188 40,000 Part Numbers and Prices are shown in red on each page. Micron Grade Grit Individual Part No. Price Each Mandrels Max Speed (RPM’s) Diamond Microfinishing Discs Priced Ea 3/4″ (19mm) PSA 125 120 A-4432 $5.10 For Use in Handpieces: 74220 A-4433 4.00 A-M415,000 45320 A-4434 3.80 30400 A-4435 2.90 20800 A-4436 1.70 9 1,200 A-4437 1.70 2″ (51mm) PSA New 125 120 A-4452 $4.50 74220 A-4453 4.40 45320 A-4454 4.40 30400 A-4455 4.40 20800 A-4456 4.40 91,200 A-4457 4.40 3 4,000 A-4583 5.80 For Use in Handpieces: A-M33 A-M338 10,000 For Use in Angle Grinder: See pg 29 10,000 Ceramic Purple Abrasives are excellent for sanding and finishing wood, metals, fiberglass, diestone, plastics, and other materials. 3M’s CubitronTM ceramic aluminum oxide mineral sharpens itself with use. Once initial grinding wears the grain flat, it fractures along micro cracks creating new cutting edges. This process repeats itself throughout the entire grinding process. • 2 to 4 times longer abrasive life than traditional aluminum oxide bands and discs • Faster stock removal with less heat and loading • Available in 60, 80, 120, 220 grit • Use Sanding Bands with 3/32″ (2.35mm), 1/8″, 1/4″ & 6mm shank rubber drum mandrels. • Use PSA Sanding Discs (pressure sensitive adhesive) on disc mandrels in 3/4″, 2″ & 3″ (19, 51, & 76mm) diameters. Also for use in new Angle Grinder, see page 28. See Mandrels on pages 19-21. Optimum Operating Speeds are much lower (between 25%–50% of maximum speeds) and also depend on the type of workpiece. Ceramic Purple Bands Priced Per 10-Pk Ceramic Purple PSA Discs Priced Below Grit 10-Pk Part No. Price per 10-Pk 60 80 120 220 Assortment 1/2″ D x 1/2″ L (13 x 13mm) 60 80 120 220 Assortment A-4922-10 $4.80 A-SD328 40,000 A-4923-10 A-SD188 A-4924-10 A-4926-10 AK4920$5.90 (3 ea of four grits) 3M Imperial Microfinishing film psa discs can be used wet or dry on metal or stone. High strength polyester film backing is coated with premium, micron graded aluminum oxide particles for greater cutting efficiency and resin bonded for increased durability. This fastcutting abrasive provides gentle, contoured polishing. Can be used in handpieces and in new Foredom Angle Grinder. See pages 19-21 for complete mandrel listing. Micron Part No. Part No. Max Speed Grade Grit $2.90/10-Pk $12.70/50-PkMandrels (RPM’s) 60 80 120 220 Assortment Always Wear Eye Protection While Using Rotary Power Tool Accessories 10 A-4932-10 $7.10 A-SD141 20,000 A-4933-10 A-SD661 A-4934-10 A-4936-10 AK4930$8.60 (3 ea of four grits) 3/4″ D x 1/2″ L (19 x 13mm) A-4962-10 $6.60 A-SD189 15,000 A-4963-10 A-SD143 A-4964-10 A-4966-10 AK4960$8.00 (3 ea of four grits) 3/4″ D x 1-1/2″ L (19 x 38mm) 60 80 120 220 Assortment A-4942-10 $14.40 A-SD145 10,000 A-4943-10 A-SD345 A-4944-10 A-4946-10 AK4940$17.20 (3 ea of four grits) 3/4″ PSA disc Grit Part No. Price per Pack 1/2″ x 1″ band Mandrels Max Speed (RPM’s) 3/4″ (19mm) Priced per 50-Pk 1/2″ D x 1″ L (13 x 25mm) For Use in Angle Grinder See Page 29 Max Speed (RPM’s) For Use in Handpieces: A-4912-10 $3.50 A-4913-10 A-SD324 40,000 A-4914-10 A-SD184 A-4916-10 AK4910$4.10 (3 ea of four grits) 60 80 120 220 Assortment For Use in Handpieces: A-M33 A-M338 10,000 For Use in Angle Grinder: See pg 29 10,000 Mandrels 1/4″ D x 1/2″ L (6 x 13mm) 2″ Imperial Microfinishing Discs 91200 A-4591-10A-4591-50 15600 A-4592-10A-4592-50 30400 A-4593-10A-4593-50 40320 A-4594-10A-4594-50 60220 A-4596-10A-4596-50 80 180 A-4598-10A-4598-50 1/2″ x 1/2″ bands 2″ PSA disc For Use in Handpieces: 60 A-5662-50 $14.80 80 A-5663-50 8.00 A-M415,000 120 A-5664-50 8.00 220 A-5665-508.00 Assortment AK5660 $9.10 (10 ea of 60, 80, 220 grit & 20 ea 120 grit) 2″ (51mm) Priced Each & 10-Pks 60 A-5682 $1.20 A-5682-10 $10.70 80 A-5683 A-5683-10 120 A-5684 A-5684-10 220 A-5685 A-5685-10 Assort AK5680 $4.00 (1 ea of four grits) For Use in Handpieces: A-M33 A-M338 10,000 For Use in Angle Grinder: See page 28 10,000 3″ (76mm) Priced Each & 10-Pks 60 A-5692 $2.70 80 A-5693 120 A-5694 220 A-5695 Assort AK5690 $9.00 A-5692-10 $22.70 A-5693-10 For Use in Handpieces: A-5694-10 A-M34 10,000 A-5695-10 (1 ea of four grits) For Use in Angle Grinder See Page 28 2″ Ceramic Purple Discs Attach with A-10041 PSA Velcro Loop Disc A-69222 Velco Hook Disc Mandrel Always Wear Eye Protection While Using Rotary Power Tool Accessories 11 3M Aluminum Oxide Sanding Bands and Discs Brushes– Mounted and Unmounted Made in USA Mounted Brushes for use in Handpieces Aluminum oxide sanding bands and discs are made of high-grade mineral and a bonding system which reduces shelling of the mineral. These economical abrasives are excellent for fast clean up and pre-polishing work. • Available in 60, 80, 120, 220 grit • Use Sanding Bands with 3/32″ (2.35mm), 1/8″, 1/4″ & 6mm shank rubber drum mandrels. • Use 2″ PSA Sanding Discs (pressure sensitive adhesive) on disc mandrels in handpieces. Also for use in new Angle Grinder, see page 28. See Mandrels on pages 19-21. Aluminum Oxide Bands Priced Per 10-Pk & 50-Pk Grit 10-Pk Part No./Price 50-Pk Part No./Price Max Speed Mandrels (RPM’s) 1/4″ D x 1/2″ L (6 x 13mm) 60 A-4612-10 $1.80 A-4612-50 $8.40 80 A-4613-10 A-4613-50 120 A-4614-10 A-4614-50 220 A-4616-10 A-4616-50 Assort AK4610 $2.10 (3 ea of four grits) For Use in Handpieces: 40,000 A-SD324 A-SD184 1/2″ D x 1/2″ L (13 x 13mm) 60 A-4622-10 $2.30 A-4622-50 $11.30 40,000 80 A-4623-10 A-4623-50 A-SD328 120 A-4624-10 A-4624-50 A-SD188 220 A-4626-10 A-4626-50 Assort AK4620 $2.70 (3 ea of four grits) 60 A-4632-10 $2.70 A-4632-50 $12.80 20,000 80 A-4633-10 A-4633-50 A-SD141 120 A-4634-10 A-4634-50 A-SD661 220 A-4636-10 A-4636-50 Assort AK4630 $3.30 (3 ea of four grits) 3/8″ D x 1/2″ L (9.5 x 13mm) 60 A-4642-10 $1.90 A-4642-50 $9.20 80 A-4643-10 A-4643-50 120 A-4644-10 A-4644-50 220 A-4646-10 A-4646-50 Assort AK4640 $2.20 (3 ea of four grits) 40,000 A-SD326 A-SD186 60 A-4652-10 $2.50 A-4652-50 $12.10 15,000 80 A-4653-10 A-4653-50 A-SD189 120 A-4654-10 A-4654-50 A-SD143 220 A-4656-10 A-4656-50 Assort AK4650 $2.90 (3 ea of four grits) 3/4″ x 1-1/2″ band 1/2″ x 1″ band Bristle Brushes are used to clean and prepare surfaces for buffing and polishing. They are made with natural animal hair–horsehair for stiff and goat hair for soft bristles. Bristles are securely held in steel rings, evenly distributed and trimmed. The wheel, cup and end shapes will work on flat, curved, hard-to-reach surfaces. Head Trim ShapeDia″Length″ Hardness 2″ Aluminum Oxide PSA Discs Priced Per 5-Pk & 10-Pk 3/32″ Shanks Grit 5-Pk Part No./Price 10-Pk Max Speed Part No./Price Mandrels (RPM’s) 60 A-5632-5 $4.30 A-5632-10 $8.00 80 A-5633-5 A-5633-10 120 A-5634-5 A-5634-10 220 A-5635-5 A-5635-10 Assort AK5630 $6.50 (2 ea of four grits) Sanding Flap Wheels For Handpieces: A-M33 A-M33810,000 Use in Angle Grinder: See page 28 10,000 Made in USA Made from economical aluminum oxide mineral. 3/4″ wheels come mounted on 1/8″ shanks in coarse (60), medium (80), & fine (120) grits. 3/16″ Thick 3/8″ Thick Coarse A-FW-1C Medium A-FW-1M Fine A-FW-1F Coarse Medium Fine A-FW-2C A-FW-2M A-FW-2F 2″ flap wheels with 3/8″ arbor holes come in five grits for use in new Foredom Angle Grinder. See page 26. Grit Part No./ Price Each 5-Pk Part No./Price Max Speed Mandrels (RPM’s) 60 A-2201 $2.20 A-2201-5 $9.80 120 A-2202 A-2202-5 240 A-2203 A-2203-5 320 A-2204 A-2204-5 600 A-2205 A-2205-5 Assort AK2200 $9.80 (1 ea of five grits) New 60 A-4662-10 $3.80 A-4662-50 $18.10 10,000 80 A-4663-10 A-4663-50 A-SD145 120 A-4664-10 A-4664-50 A-SD345 220 A-4666-10 A-4666-50 Assort AK4660 $4.50 (3 ea of four grits) Always Wear Eye Protection While Using Rotary Power Tool Accessories 12 2″ PSA disc Part Numbers and Prices are shown in red on each page. 3/4″ D x 1-1/2″ L (19 x 38mm) Wheel End Mounted Bristle Brushes Priced Below 2″ Flap Wheels with 3/8″ arbor holes Priced Ea & 5-Pks 3/4″ D x 1/2″ L (19 x 13mm) 25,000 RPM Cup Max Speed 3/4″ Dia., 1/8″ Shanks $7.70 Ea 1/2″ D x 1″ L (13 x 25mm) 1/2″ x 1/2″ bands 2″ Flap Wheels Mount with A-69212 Short Hub Use in Angle Grinder: See page 26 10,000 2″ PSA Discs & Flap Wheels for Use in Angle Grinder See Pages 26 & 28 cup wheel wheel end end 9/16 9/16 3/4 3/16 1/4 1/8″ Shanks cup wheel wheel 9/16 3/4 3/4 Part No. Price Each 5/32 1/8 3/16 1/4 3/8 Stiff Stiff Stiff Stiff Stiff A-MB1$1.70 A-MB251.20 A-MB21.50 A-MB31.50 A-MB351.40 1/4 3/16 3/16 Stiff Stiff Soft A-MB18$1.50 A-MB281.50 A-MB2381.70 Mounted Steel Brushes Priced Below Steel Brushes are suitable for use on all metal surfaces for removing rust and corrosion, deburring, cleaning, edge blending, and other surface texturing and preparation. Made with .003″ and .005″ wire. Head Trim Wire ShapeDia″Length″ Size 3/32″ Shanks end wheel wheel 3/16 3/4 3/4 1/8″ Shanks cup end end wheel wheel wheel 5/8 3/16 5/16 3/4 3/4 1 Part No. Price Each 1/4 3/16 3/16 .003 .003 .005 A-MB5$1.80 A-MB732.80 A-MB72.30 1/4 1/4 9/16 3/16 3/16 5/16 .005 .003 .005 .003 .005 .003 A-MB128$3.10 A-MB582.00 A-MB5385.00 A-MB7384.90 A-MB783.30 A-MB8383.30 Made in USA Unmounted Wire & Nylon Brushes for use in BL Bench Lathe A-UB33 A-W302 A-W301 & Handpieces 18,000 RPM Max Speed A-UB33 and A-W302 steel wire brushes are used for texturing, removing rust and corrosion, edge blending and polishing of cast or machined metal surfaces or hard-to-reach areas. These are used with mandrels in flex shaft handpieces or wheel mandrels (A-WM-5, A-WM-6) on the Foredom BL Bench Lathe. Soft nylon Brush A-W301 is great at very low speeds for cleaning up “fuzzies” left behind on delicate carvings without removing any of the fine detail. It can be used with a mandrel on a handpiece or mounted directly onto a tapered spindle of the BL Lathe. Cotton Buff A-CB1, below, has same mounting options. Brushes can also be used on discontinued High Speed Bench Grinders. Part No.Dia″ Material A-UB33 1-3/8 Wire A-W302 2 Wire A-W301 2 Soft Nylon Wire Hole Use with Price Size″Size″Mandrel Each .008 1/4 A-M8, A-M85 $6.80 .008 1/4 A-M8, A-M85 8.40 N/A 3/16 A-M78 6.20 or Tapered Spindles of Lathe 18,000 RPM Max Speed Unmounted Buffs and Abrasive Stone for use in BL Bench Lathe & A-10072 Handpieces A-CB1 A-W305 Part No.Dia″ Material Hole Size″Thick″ Use withPrice MandrelEach A-CB1 2-1/2 A-W305 2 A-10072 1-3/4 Cotton Buff Pin 1/2 A-M78of Lathe $2.90 Felt Buff 1/4 3/8 A-M8, A-M85 3.80 Alum Oxide 1/4 3/8 A-WM-3 or A-WM-4 4.80 A-WM-5 or A-WM-6 Wheel ManGrinding Stone drels for use on Bench Lathe Tapered Spindles Unmounted 2″ Abrasive Wheels for use on BL Bench Lathe with A-WM-5 and A-WM-6 Wheel Mandrels 2″ Dia. x 1/4″ Thick with 1/4″ arbor holes $4.80 Ea New Mounted Brass Brushes Priced Below Brass Brushes are suitable for use on all metal surfaces for removing rust and corrosion, deburring, cleaning, edge blending, and other surface texturing and preparation. Made with .003″ and .005″ wire. Head Trim Wire ShapeDia″Length″ Size 3/32″ Shanks end wheel 1/8 3/4 1/8″ Shanks wheel 1 Part No. Price Each 1/4 3/16 .003 .005 A-MB4$1.80 A-MB62.30 5/16 .005 A-MB68$2.90 12 3 4 1 2 3 4 5 6 Part No. A-10074 A-10073 A-10075 A-10077 A-10078 A-10076 5 6 Material Grit CeramCut Blue White Aluminum Oxide (1-7/8″) Salt & Pepper Silicon Carbide Black Silicon Carbide Green V Stone 120 400 11,000 RPM 46 100 Max Speed 100 46 Always Wear Eye Protection While Using Rotary Power Tool Accessories 13 3M Radial Bristle Discs– 9/16″, 3/4″, 1″ 9/16″ Diameter with 1/16″ arbor hole 6-pack 12-pack 24-pack $11.90 $21.50 $42.20 120 grit/white A-4522-6A-4522-12 A-4522-48 30,000 RPM Max Speed Recommended Operating Speed for most applications is 3,000– 18,000 RPM (5,000 RPM for woodcarving). Slower speeds allow greater 50 grit/green A-4533-6A-4533-12 A-4533-24 flexibility and a softer touch with the bristles. Use the tips of the bristles with light pressure to extend the life of the accessory and achieve more subtle results. Higher speeds provide more aggressive 80 grit/yellow material removal. 400 grit/blue A-4524-6A-4524-12 A-4524-48 Pumice (1,200 grit) pink A-4526-6A-4526-12 A-4526-48 6 micron (3,000 grit) peach A-4527-6 A-4527-12 A-4527-48 A-4534-6A-4534-12 A-4534-24 1 micron (14,000 grit) light green A-4528-6A-4528-12 A-4528-48 3/4″ Diameter with 1/16″ arbor hole 120 grit/white A-4535-6A-4535-12 A-4535-24 6-pack 12-pack 48-pack $9.40 $18.80 $74.90 80 grit/yellow A-4511-6A-4511-12 A-4511-48 Made in USA Stack 6 or more discs onto a mandrel for making a sturdy brush. Discs are not used individually except when working in the narrowest of channels. 120 grit/white A-4512-6A-4512-12 A-4512-48 Mandrels for use with Radial Bristle Discs 220 grit/red A-4513-6A-4513-12 A-4513-48 400 grit/blue A-4514-6A-4514-12 A-4514-48 Pumice (1,200 grit) pink A-4516-6A-4516-12 A-4516-48 6 micron (3,000 grit) peach A-4517-6 A-4517-12 A-4517-48 1 micron (14,000 grit) light green A-4518-6A-4518-12 A-4518-48 Part No. Shank Arbor A-M1 3/32″ k k 1/16″ A-M2 3/32″ 1/8″ A-M6 1/8″1/16″ A-M20 1/8″1/8″ A-M14 A-M15 9/16″ 3/4″ 1″ k k k 1/8″1/8″ k k 1/8″1/16″ k k 2″ Dia 6-pack $20.80 3″ Dia 2″ Discs 30,000 RPM Max Operating Speed 3″ Discs 20,000 RPM Max Operating Speed 80 grit/yellow A-4542-6 80 grit/yellow A-4552-6 Recommended Speed for most applications is 5,000– 18,000 RPM 36 grit/brown A-4532-6A-4532-12 A-4532-24 220 grit/red A-4523-6A-4523-12 A-4523-48 Radial Bristle Discs– 2″ & 3″ with 3/8” arbor hole. Made in USA 1″ Diameter with 1/8″ arbor hole 6-pack 12-pack 48-pack $9.40 $18.80 $74.90 3M Recommended Speed for most applications is 5,000– 18,000 RPM 2″ and 3″ Scotch-Brite Radial Bristle Discs share the same excellent properties as the smaller sizes shown on the opposite page. These larger discs can be stacked on mandrels for use with flex shaft and micromotor handpieces, and on spindle adapters for the BL bench lathe. 2″ discs can also be used with special mounting hubs on Foredom’s new Angle Grinder attachment. See mandrels listing below. When using on the lathe, Radial Bristle Discs are most effective at speeds of 5,000 to 7,000 RPM. For Woodcarvers Scotch-Brite Radial Bristle Discs are superior Assortment Kits to sandpaper, flap wheels, or with Mandrels Part No. Price other types of sanders, brushes 9/16″–37-pc kit AK4520 $56.80 or abrasive wheels for many 6 discs ea. of 120, 220, 400, Pumice, 6 micron, woodcarving and woodwork& 1 micron plus A-M1 mandrel (3/32″) ing applications. Their flexible 3/4″–38-pc kit AK4510 $58 bristles can sand areas with 6 discs ea. of 80, 220, 400, Pumice, 6 micron, and detail, irregular, curved, or flat 1 micron plus A-M1 (3/32″) and A-M6 (1/8″) mandrels surfaces on soft or hard woods. Carvers can remove the “fuzz3/4″–10-pc kit AK4519 $17 ies” left behind without harm3 discs ea. of 80, 400, & 6 micron + A-M6 (1/8″) mandrel ing any of the underlying detail. 1″– 25-pc kit AK4530 $44.20 The coarser grits can be used 6 discs ea. of 36, 50, 80, & 120 grit + A-M20 (1/8″) mandrel to carve and texture, while the 1″–10-pc kit AK4539 $23 finer grits will smooth, burnish, 3 discs ea. of 36, 80, and 120 grit + A-M20 (1/8″) mandrel and polish. 120 grit/white A-4543-6 120 grit/white A-4553-6 220 grit/red A-4544-6 Part Numbers and Prices are shown in red. Scotch-Brite Radial Bristle Discs have thin flexible bristles that get into hard to reach areas without removing detail or making flat spots. 3M Cubitron™ and aluminum oxide grain embedded throughout the bristles enable them to work faster and last far longer than rubber wheels, regular brushes, buffs or conventional sanders. They generate little or no dust nor the heat associated with wheels and buffs. For Dental Labs & Jewelers These non-contaminating discs are ideal for cleaning metal surfaces, removing light fire scale and oxide, finishing, blending, texturing, pre-polishing and polishing all precious and nonprecious metals, dental acrylics, flexite, and ceramics. 6-pack $28.30 220 grit/red A-4554-6 400 grit/blue A-4545-6 Pumice 1,200 grit/pink A-4546-6 6 Micron 3,000 grit/ peach A-4547-6 Mandrels for use with 2″ and 3″ Radial Bristle Discs Part No. Arbor Hole/ Shank Size 2″ 3″ For Use with Handpieces: A-M30 (Flat Head) 1/4″ A-M31 (Screw) k k 1/4″ k k For Use with Bench Lathe: A-4561 (Right)3/8″ Black Tapered Spindle Adapter A-4562 (Left)3/8″ Grey Tapered Spindle Adapter For Use with Angle Grinder: A-69212 (Short Hub) A-69212L (Long Hub) k k k k k k 400 grit/blue A-4555-6 Pumice 1,200 grit/pink A-4556-6 1 Micron 14,000 grit/ light green A-4548-6 6 Micron 3,000 grit/ peach A-4557-6 1 Micron 14,000 grit/ light green A-4558-6 Always Wear Eye Protection While Using Rotary Power Tool Accessories 14 Always Wear Eye Protection While Using Rotary Power Tool Accessories 15 Felt Buffing and Polishing Accessories Made in USA. 20,000 RPM Max Speed Felt Buffing and Polishing Accessories are used with compounds on hard and soft metals, metal plate, precious metals, plastics, wood, acrylic, and painted surfaces. Select the appropriate compound, below, for the material being worked to produce desired finish. AKFK3 $34.80 16-Pc Kit Mounted Felt Bobs 1/8″ shanks Contains all 8 shapes below in medium and hard densities 1/8″ (3.18mm) Shank Mounted Felt Bobs Priced Ea Cotton and Felt Polishing Buffs More About Felt: Felt is a compound carrier and the abrasives in compounds perform the actual polishing function. However, surface speed, felt hardness, applied pressure, and frictional contact determine the amount of surface removal, or polishing desired. “Cutting down” refers to a greater amount of surface removal than does “coloring”. Whether someone uses the term buffing, polishing or finishing, they typically mean a 2-step process of cutting and then coloring by which the luster or reflectiveness of a product is enhanced. with 1/8″ & 3/32″ arbor holes Priced per 10-Pk Medium Density ONLY Part No. A-MS1* A-MS3* A-MS4* A-MS6* A-MP1* A-MP4* A-MP5* A-MP8* A-C1M A-C2M A-C3M Dia. ″ 1/2 1/21/2 1/21/4 3/8 1/2 3/4 1/4 3/8 1/2 Lgth/Thick″ 1 13/41/21/41/21/2 3/4 1/2 3/4 1 Price $2.75 $2.75$2.75 $2.75$1.40 $1.55 $1.70 $2.75$13.20/10$15.90/10 22.90/10 Mandrel A-M3 (3/32″) A-M7 (1/8″) A-M7 (1/8″) Please specify Medium or Hard Density when ordering by adding M or H * Shank Size to Part No. Part Numbers and Prices are shown in red. 4 6 7 Made in USA AK4000 4 Bar Kit – Includes A-4001 Emery, A-4002 Tripoli, A-4003 White 1 2 3 Diamond, A-4004 Red Rouge Kit 22.25 oz. AK4000$11.10 All of our polishing compounds come in standard size Emery bars. We also offer Platinum Blue, Platinum White, and Red Rouge in 6.5 oz. bar A-4001$2.70 small tubes that are sized and priced right for getting started with a new 19 oz. bar A-50019.20 compound. Platinum BlueTM and Platinum WhiteTM are unique formulations that are only available from Foredom®. 4.5 oz. bar A-4002$2.70 1 Emery (Black) 14 oz. bar A-50029.20 Contains coarse grit to remove surface White Diamond Rouge imperfections, scratches, rust, and burrs from 5.5 oz. bar A-4003$2.70 iron, steel and other hard metals. Tripoli 17 oz. bar A-50039.20 2 Tripoli (Brown) Most popular compound for general cutting Red Rouge down, scratch removal, buffing, & coloring on 5.75 oz. bar A-4004$2.70 non-ferrous metals such as zinc die castings, 17 oz. bar A-50049.20 brass, copper, aluminum castings and sheets. 1 oz. tube A-400412.00 3 White Diamond Rouge Platinum Blue Fast cutting on hard metals. Made with fine 5 oz. bar A-4007$6.50 abrasive powder that produces a final satin 1oz. tube A-400712.50 finish on chrome, stainless steel, carbon steel, brass, and aluminum. Also use to remove rust, Platinum White scale and carbon deposits on metal surfaces. 5.75 oz. barA-4006 $9.20 4 Red Rouge 1 oz. tube A-400612.50 Produces a high luster on gold, silver, pewter, Carnauba 2 oz. bar A-4008$9.20 nickel plating and plastics for final polishing. Always Wear Eye Protection While Using Rotary Power Tool Accessories 16 Loose White Muslin Buffs White Muslin Buffs These buffs have only one row of stitching around the arbor hole which is reinforced with leather and shellac (L/S). Made of Finex (80 x 80 weave) muslin with combed edges. The open layers provide a softer polishing action and conform to contours and curves. Use with rouge for coloring or final polishing operations. Rows of Center Part Dia.PlyStitching Hole No. Price Each Part Dia.Ply No. 3″ 35 Price Each A-LCB35$3.35 3″40 A-LCB33.70 2″ and Smaller Diameter Buffs for use with Mandrels in Handpieces 25,000 RPM Max Speed Small diameter buffs mount on mandrels for use in Foredom Handpieces. White Muslin A-CB2 and A-CB12 are made from fine (80 x 80) weave muslin for use with all types of compounds. They work with A-M1, A-M6, A-M7, A-M13, and A-M15 mandrels. Rows of Part Dia. Thick Ply StitchingNo. Price Each 1″3/16″ 16 2 A-CB2$1.30 1-1/2″3/16″ 16 3 A-CB122.40 1″40 1 S A-CBC1$2.15 4″40 A-LCB44.90 2″40 1 S A-CBC22.30 Square Edge Solid Felt Buffs 3″40 3 S A-CBC33.35 Yellow Treated Cotton Buffs 4″40 3 S A-CBC44.55 6″50 4 S* A-CBC658.00 7″50 4 S* A-CBC759.85 Square Edge Solid Felt Buffs shown below are made from tightly compressed, top quality wool felt and come in Medium and Hard densitities. Use for polishing and lapping flat surfaces. They will hold an edge for working in angles and corners. Priced per 10-Pk* Fine Weave (80 x 80) Finex Muslin hold compounds well but the tighter weave results in longer life. The center pin holes are reinforced with shellac (S) for a tight fit on tapered mandrels and greater durability. Combed edges do not require break in or combing to hold compound. The fine weave and stitching make them durable and especially suitable for polishing with rouge. Rows of Center Part Dia.PlyStitching Hole No. Price Each Made with chemically treated extra fine (86 x 80) weave fabric, these buffs are stiffer than untreated ones. They will cut faster and last 2 to 3 times longer than white muslin buffs. Combed edges hold compounds without break PartPrice in or combing. Center pin holes are reinforced Dia. Thick HardnessNo. 10-Pk with shellac (S) or leather and shellac (L/S). 1/2″1/8″ Medium A-SE1M$5.00 Rows of Center Part Dia.PlyStitching Hole No. Price Each 1/2″1/8″ Hard A-SE1H$5.00 S A-CBF1$2.40 4″30 3 S A-CBY43$5.60 5/8″3/16″ Medium A-FB4$5.30 2″40 1 S A-CBF22.40 4″40 3 S A-CBY46.70 3/4″1/8″ Medium A-SE2M$7.10 3″40 3 S A-CBF33.70 5″40 3 L/S A-CBY57.90 3/4″1/8″ Hard A-SE2H$7.10 4″40 3 S A-CBF44.80 6″40 4 L/S A-CBY69.10 3/4″1/4″ Medium A-FB3$7.10 6″50 4 S A-CBY65-S11.40 1″1/8″ Medium A-SE3M$9.40 1″1/8″ Hard A-SE3H$9.40 5 Platinum Blue For pre-polishing and cutting down of platinum and other metals. Also for final polishing on acrylics. 1″40 1 6 Platinum White Use for final polishing. Produces a deep luster high color final polish on platinum, gold, silver, and all metals. Also for final polishing on flexible partial material and acrylic. 7 Carnauba The hardest natural wax available. Non-tacky and highly regarded for its tough and wear resistant qualities. It is especially good for producing a high luster on wood & painted surfaces. Buffs 3” and larger are for use on bench lathe tapered spindels at 5,000 RPM Max Speed *Extra thickness eliminates need for leather reinforcements. 5 Polishing Compounds Made in USA. Use 1″ and 2″ buffs with an A-M78 mandrel at 20,000 RPM Max Speed Coarse Weave (60 x 60) Muslin have a more open weave to hold more compound. Used as a general purpose buff with cutting and polishing compounds. Combed edges do not need breaking in or combing to hold compound. The center pin holes are reinforced with shellac (S) for a tight fit on tapered mandrels and greater durability. Unmounted Felt Bobs Flannel (Canton) Buff Razor Edge Yellow Treated Buff Made with chemically These canton flannel treated (86 x 80) weave buffs are made with muslin for added stiffthicker, softer fabric. ness and longer life. The Excellent for final polishing additional stitching and with rouge on precious metals leather + shellac (L/S) (especially good on high karat gold and silver). center keeps wheel stiff Center pin holes are reinforced with shellac (S) while in use. Used for cutting and polishing in for a tight fit on tapered mandrels.grooves, crevices and inside curves. Rows of Center Part Price Dia. Ply Stitching Hole No. Each Dia.Ply 3″30 2 S A-CFB3 $4.55 4″ 28 at center. 12 ply at outside edge. Center Hole L/S Part No. * Sold Individually: 2″3/8″ Medium A-SE4M$4.40 Price Each A-CYR4$5.40 Always Wear Eye Protection While Using Rotary Power Tool Accessories 17 Ruby Carvers Made in Switzerland. 35,000 RPM Max Speed Screw and Tapered Mandrels Long lasting Fine Grit Ruby Carvers, with ruby crystals firmly bonded to metal frame, provide a smooth finish on hard materials such as steel, porcelain, glass, acrylic, soft and precious metals, and wood. Standard (Coarser) Grit Ruby Carvers provide faster material removal but leave a slightly rougher finish. These are well suited for woodcarving. Maximum and Recommended Speeds vary depending on the type and size of the accessory as well as the mandrel in use. Screw Type Mandrels 2.35mm (3/32″) Shank Ruby Carvers in 2 Grits- Fine $11.50 Ea & Standard $14 Ea Part Arbor Hole/ Overall Price No. Shank″ Capacity″Length″Each Part Numbers and Prices are shown in red. A-RC15 A-RC19 A-RC20 A-RC11CA-RC13CA-RC14CA-RC15CA-RC16CA-RC32CA-RC34CA-RC36C Part No. Fine Fine Standard Standard Grit 4.53.34.08.56.57.57.56.55.55.55.5 Head Dia. mm 4.5 8.0 10.016.0 19.0 7.5 12.012.0 10.010.013.0 Head Lgth mm 3/32″ (2.35mm) Shank $2.30 Ea Drills– Step, Twist & Carving 3/32″ Shank Step Drills $2.30 Ea Made in Switzerland. 30,000 RPM Max Speed D Made from hardened tool steel with 3/32″ L (2.35mm) shanks and an overall length of 1.8″ (45mm). Use for drilling all types of wood, precious metal, mild steel, bone, and mother of pearl. Head Dia (D) mm inches .5.0197 .6 .0236 .7 .0276 .9 .0354 1.0 .0394 1.1 .0433 1.4 .0551 1.5 .0591 2.0 .0787 2.2 .0866 Head Length (L) 8.5 8.5 8.5 8.5 8.5 10.5 10.5 11.0 11.0 11.0 Approx Wire Size Part No. #76 A-58005P #73 A-58006P #70 A-58007P #65 A-58009P #61 A-58010P #57 A-58011P #54 A-58014P #53 A-58015P #47 A-58020P #44 A-58022P A-5523 Satin Finisher Extra Fine 7/8 1/4 A-5517 Satin Finisher Fine 7/8 1/4 Steel Carving Drills $7.90 Ea Tapered carving drills made of high tempered steel with three flutes. Designed for internal carving and shaping of wood, acrylic and plastic. 20-Pc High Speed Steel Twist Drill Set Z-37-150 $25.95 Miniature twist drill set in plastic dis- 20-Pc Diamond Twist Drill Set AK2061 $16.30 New penser with one each of high speed twist Diamond coated, wire gauge twist drill set in plastic dispenser. These straight shank drills are made of high quality steel with diamond coating. Set contains one each of drills #61 to #80 (.025″ – .053″). drills in metric sizes from 0.3mm - 1.6mm. Includes: 0.3, 0.35, 0.4, 0.45, 0.5, 0.55, 0.6, 0.65, 0.7, 0.75, 0.8, 0.85, 0.9, 0.95, 1.0, 1.2, 1.3, 1.4, 1.5, and 1.6. or use in small pin vise and other hand tools that hold wire gauges or in rotary handpiece with A-M50 and A-MC2 micro chucks. Always Wear Eye Protection While Using Rotary Power Tool Accessories 18 A-5524 Part No. Satin Finisher Type Coarse Style/Grit 7/8 Head Dia.″ 1/4 Head Lgth″ 7/8 1.7040,000 A-M133/32 1/16 1-7/8 2.2030,000 A-M14 1/8 1-7/8 2.2030,000 A-M8 1/8 1/4 1-11/16 5.5020,000 A-M15 1/8 1/16 1-3/4 1.7040,000 A-M19 1/8 1/16 1-7/8 2.2030,000 A-M2 3/32 1/8 1-7/8 2.8020,000 A-M6 1/8 1/16 1-3/4 1.7040,000 A-M20 1/8 1/8 1-3/4 1.7020,000 A-M831/8 1/8 2-1/8 2.2020,000 A-M841/4 1/8 2-1/8 2.2020,000 Screwdriver A-PS83 $3.90 1/8 5″ long, double ended screwdriver fits many of the small size screws we use on mandrels, flex shaft motor connectors and other products. Has both flat blade and phillips tip and pocket clip. unmounted felt bob on A-M7 mandrel Tapered Mandrels Part Arbor Hole/ Overall Price No. Shank″ Capacity″Length″Each A-M851/4 1/4 Max Speed A-M12 1/81/8 1-3/4 $1.7040,000 A-M3 3/32 3/32 1-3/4 1.7040,000 A-M91/8 3/32 1-3/4 1.7040,000 A-M7 1/8 Made in USA. 25,000 RPM Max Speed 2-1/8 2.2020,000 1-3/4 1.7040,000 A-M78 1/8 3/16 2-3/8 3.7020,000 A-M16 1/8 1/8 2-3/4 2.4018,000 A-M17 1/8 3/16 2-3/4 3.7018,000 1/8 For use with cartridge rolls A-M30 1/4 3/8 A-CD1 A-CD2A-CD3 Miniature drill set in plastic dispenser 1/16″3/32″1/8″ with one each of high speed twist drills in wire gauge #61 - #80. For use in small pin vise and other hand tools that hold wire Wire Decimal Metric (mm) gauges or in rotary handpiece with A-M50 GaugeEquivalentEquivalent and A-MC2 micro chucks. 61.0390 0.99 20-Pc Metric High Speed Steel Twist Drill Set Z-37-151 $25.95 A-M103/32 1/16 Maximum speeds shown are based on a 1″ overhang with an accessory that weighs under 1 gram and is smaller than 1/2″ in diameter. As a general rule, smaller accessories and mandrels can be used at higher speeds than larger accessories and mandrels. It is a good idea to follow the recommendations that come with both the accessory and mandrel you are using. Made in USA. 25,000 RPM Max Speed A-5520 Muslin Loose 1 1/4 Max Speed A-M1 3/321/16 1-3/4$1.2040,000 Muslin Wheel and Satin Finishers Mounted polishing wheels provide a variety of finishes depending on compound applied (see page 16). Fine and coarse satin finishers have nylon heads impregnated with abrasive grit. Use to clean and obtain matte finishes on metal or plastic surfaces. Made in USA and Germany 62.0380 63.0370 64.0360 65.0350 66.0330 67 .0320 (1/32) 68.0310 69.0292 70.0280 71.0260 72.0250 73.0240 74.0252 75.0210 76.0200 77.0180 78 .0160 (1/64) 79.0145 80.0135 0.97 0.94 0.915 0.890 0.84 0.813 0.788 0.741 0.711 0.660 0.635 0.610 0.5715 0.533 0.508 0.457 0.464 0.368 0.343 1-5/8 3.0025,000 2″ Velcro Hook Sanding Heads with 3/8″ arbor holes, featured on page 28, can be mounted onto A-M30 & A-M31 mandrels for use in Foredom Handpieces. A-M31 1/4 3/8 2 These adapters are used to mount accessories onto the tapered spindles of Foredom’s BL lathe. Use the A-4561 and A-4562 for 3M ScotchBrite Radial Bristle Discs and the A-4568 for mounting FX & other wheels with a 1″ 6.00 25,000 holes. 10,000 RPM Max Speed See next page for Angle Grinder Mounting Mandrels and Hubs Sandpaper Split Mandrels These mandrels have slots for inserting and wrapping small pieces of sandpaper. 20,000 RPM Max Speed Part No. Shank″ Adapters for Mounting Accessories on to BL Lathe Slot Head Lgth″ x Overall Price Dia″Width″Length″ Each A-M21 3/32 1/18 3/4 x 1/32 2-3/8 $1.70 1/16 at tip A-M22 3/32 5/32 3/4 x 1/32 2-3/8 1.70 Side of Part No. Lathe Arbor Price Hole″Each A-4561 Right Hand Side 3/8 A-4562 Left Hand Side 3/8 $2.10 2.10 A-M233/325/32 3/4 x 1/32 2-3/8 1.70 A-M24 3/32 3/32 3/4 x 1/64 1-3/4 1.20 A-4568 Both Sides 1 5.30 A-M24LG 3/32 3/32 1/2 x 1/64 2-3/16 1.20 A-M26 1/83/16 3/4 x 1/32 2-3/8 1.90 Always Wear Eye Protection While Using Rotary Power Tool Accessories 19 Rubber Drum Mandrels 3/32″ and 1/8″ Shank Head Head Total Dia.″Length″Length″ Rubber Sanding Disc Mandrels Made in USA Max Speed RPM 3/32″ shank Part No. Price Each 1/8″ shank Part No. 1/4 1/21-7/8 40,000 A-SD324$3.50 A-SD184 $3.50 1/4 1/22-1/4 15,000 A-SD40 3.40 3/8 1/21-7/8 40,000 A-SD326 3.80 1/2 1/2 1-7/8 40,000 A-SD328 4.20 3/4 1/2 1-7/8 20,000 N/A Price Each A-10040 Velcro Hook PSA Discs turn A-M338 and A-M33 into ‘velcro-friendly’ mandrels for use with 2″ psa sanding discs that have been added to the line for our new Angle Grinder Attachment. A-10041 Velcro Loop Discs are also needed to adhere sanding discs. (See pages 28-29 Velcro for details.) New N/A A-SD186 3.80 A-SD188 4.40 A-SD189 4.40 A-M4 A-M338 1/8 1/8 Hook 1/2 1-3/4 A-10040-5 (5-Pk) Surface 1-1/2 2 $5.50 15,000 10,000 A-10040-25 (25-Pk) $4.80$8.40 $20 Left Hand Threaded Mandrels 3/32″ Shank– For running in Reverse Operation 40,000 RPM Max Speed 1/4″ Shank Part No. The left handed threads on these mandrels hold accessories securely and self tighten while running in reverse in flex shafts and micromotors. They have notches on their shanks for easy identification. A-SD324L, A-SD326L and A-SD328L also have black left hand threaded screw tops. HeadMax Dia″ x Price Speed Length″ Each RPM A-SD141 1/2 x 1 A-SD143 3/4 x 1/2 Part No. $5.6020,000 4.4020,000 1/16 1-3/4$2.20 A-M7L 1/8 1-3/41.70 Part No. 4.5015,000 A-SD145 3/4 x 1-1/2 9.5010,000 Includes wrench. 2-3/4 overall length New Mandrel, Hubs, and Arbor for Mounting Accessories on to Angle Grinder: 6mm Shank Part No. HeadMax Dia″ x Price Speed Length″ Each RPM These special mounting tools are used to attach 2″ sanding and grinding accessories onto Foredom’s new Angle Grinder Attachment for the H.30 Handpiece. See pages 26 - 29. Maximum Speeds vary depending on the type and size of the accessory. A-SD345 3/4 x 1-1/2 $9.5010,000 Includes wrench. 2-3/4 overall length 2″ Velcro Hook Backed Rubber Disc Mandrel 8mm x 1mm thread A-SD661 1/2 x 1 8.6020,000 Short Hub Includes 8mm hex screw UA690 A-SD662 3/4 x 1 8.6015,000 Part Numbers and Prices are shown in red on each page. Always Wear Eye Protection While Using Rotary Power Tool Accessories 20 Long Hub Includes 14mm hex screw UA691 Sanding Disc Arbor 8mm x 1mm thread Part No. Price Each A-69222$5.00 for mounting PSA Sanding Discs with A-40041 Velcro Loop backed PSA Discs Bur Holders Burs Not Included A-10082 $15.90 Rotating Bur and Tool Holder– For 1/8″ and 1/4″ Shank Burs, Drill Bits 1/16″–5/32″. Organizes up to 112 accessories. Stores: 92– 1/8″ shank and 13–1/4″ shank burs. Has 7 marked holes for drill bits 1/16″ to 5/32″. 3″ deep x 2-3/4″ dia. center cup holds small tools such as files and screwdrivers. Measures 6-1/2″ wide x 4″ high (165 x 102mm). A-692124.00 for mounting Radial Bristle Discs and Grinding Wheels A-69212L4.00 A-692235.00 mounting Quick for Change Sanding Discs A-10081 $15.90 Rotating Bur Holder– For 3/32″ (2.35mm) Burs and Small Tools. Organizes 114– 3/32″ burs. Measures 6-1/2″ wide by 4″ high (165 x 102mm) and has a 3″ deep x 2-3/4″ dia. center cup to hold small tools such as files, scribes and screwdrivers. Arbor Hole/ Overall Price Capacity″Length″Each A-M1L A-SD324L A-SD144 3/4 x 1 Made in USA Head Dia″/Overall Price Length″Length″Each 1/4 x 1/2 1-3/4$7.10 A-SD326L3/8 x 1/2 1-3/4 7.10 A-SD328L 7.10 1/2 x 1/2 1-3/4 A-M33 1/4 1-3/4 2 10,000 $7.90 A-M34 1/4 2-3/4 2 10,000 $8.40 Part No. Shank Dia.″ Overall Length″ Max Speed - RPM Price Each Micro Chucks and Collet Adapters Micro Chucks A-M50 and A-MC2 hold various sizes drills. Collet Adapters A-M52 and HPL4 part nos. are used to “step down” the collet size without having to actually change the collet in your handpiece. This is a great way to easily use a smaller diameter shank accessory quickly without any of the work involved with changing collets. Price Part No. 10,000 RPM Max Speed A-M50 A-M52 20,000 RPM Max Speed A-MC2 Shank″ Use With Each 3/32 drills 70-80$6.10 1/16″ shank friction grip burs 3/32″ (2.35mm) 3/32 in8.60 collet handpieces 1/8 drills 60-8017.10 10,000 RPM Max Speed 1/16″ shank HPL4-32333/32 accessories $16.30 HPL4-32341/8 HPL4-32353mm HPL4-32361/8 HPL4-32373mm 1/16″ shank 16.30 accessories 3/32″ shank 16.30 accessories 3/32″ shank 16.30 accessories 1.6mm shank 16.30 accessories A-10080 $15.90 Rotating Bur Holder– Universal For All Size Shanks. Organizes 126 accessories including 1/16″, 3/32″, 1/8″, and 1/4″ shanks. Measures 6-1/2″ wide by 4″ high (165 x 102mm) and holds 69– 3/32″ or 1/8″ burs (in 2-step holes), 12–1/4″ burs, and 45–1/16″ burs. A-10088 $3.50 Small Round Bur Holder– For 3/32″ (2.35mm) & 1/8″ Burs. Holds up to 48 burs with 24 holes for each size shank. Measures 2-1/8″ in dia. by 2-1⁄2″ high (54 x 64mm). Holds burs up to 2″ long. Includes clear cover. A-10089 $3.50 Small Square Bur Holder– For 3/32″ (2.35mm) & 1/8″ Burs. Holds up to 52 burs: 34–3/32″ and 18– 1/8″ shank accessories. Measures 2-1⁄2″ (64mm) sq. x 2-1⁄4″ (54mm) high. Holds burs up to 2″ long. Includes clear cover. Always Wear Eye Protection While Using Rotary Power Tool Accessories 21 Vanadium Steel Cutters Carbide Burs Made in USA. 45,000 RPM Max Speed These are superior quality high speed vanadium steel cutters for shaping, grooving, slotting and cutting in wood, plastic and soft metal. Made in USA Standard flute Carbide Burs are used for easy material removal and leave a smooth finish. They are ideal for use on hard wood and most metals including stainless steel, steel alloys, cast iron, etc. 100,000 RPM Max Speed for 1/8” and smaller diameters carbides, 35,000 RPM Max Speed for 1/4” diameter carbides. 1/8″ (3.18mm) Shank Priced Below 1/8″ (3.18mm) Shank Priced Below A-7104A-7106A-7112A-7113A-7122A-7143A-7145A-7153 Part No. 3/165/161/85/165/161/43/8 3/8 Head Dia.″ 3/16 5/16 1/4 3/8 13/32 15/32 9/16 1/16 Head Length″ $8.80$9.90$7.70$9.90$9.90$9.90$9.90$9.90 Price Each High Speed Vanadium Steel Fluted Engraving Burs Made in Switzerland 2.35mm (3/32″) Shank 1-3/4″ Overall Length 5-Pc Kit AK65 $1.30 Ea. $4.90 with one of ea. bur at left For etching, engraving, and other fine detailing work on metal, wood, glass, ceramics, etc. Ball Ball Ball Inv Cone Inv Cone Shape A-R2A-R5 A-R7 A-P3 A-P7 Part No. 1/32 (.79) 1/16 (1.6)3/32 (2.35)1/32 (.79)3/32 (2.35) Head Dia.″ (mm) 1/32 (.79) 1/16 (1.6)3/32 (2.35)3/64 (1.19)5/64 (1.98) Head Length″ (mm) 3M Wet/Dry Micron Graded Polishing Papers $20.60 Per 10-Pack of 8-1/2″ x 11″ Sheets Part No. Price Grade Grit Color A-5968-10$20.60 1 micron 10,000 white A-5967-10 20.60 2 micron 6,000 aqua A-5966-10 20.60 3 micron 4,000 pink A-5964-10 20.60 9 micron 1,200 lt. blue A-5963-10 20.60 15 micron 800 gray A-5962-10 20.60 30 micron 400 green AK5960$12.20 6-pc Assortment Pack of 8-1⁄2″ x 11″ sheets–1 of each grade AK5961$6.206-pc Assortment Pack of 4-1⁄4″ x 11″ sheets–1 of each grade Z-37-959$12.00 Super Bond Film Tape 1″ x 36 yard use for making belts for hand sanders Polishing paper is a soft cloth-like material for use on any contoured surface with or without water. Working in sequence from the most coarse to the finest sheet brings the best results. 8-1⁄2″ x 11″ sheets come in six micron grades in packs of 10 per grit. Papers can be cut lengthwise into 1-1⁄2″, 1″, 3/4″ or 1/2″ wide strips, taped, and made into rolls for use on Finger Sanders and Sanding Sticks. Papers can also be cut into much smaller pieces, wrapped and glued for use on split mandrels, see page 19. Latch Type Burs for Angle Head Handpieces H.55A, H.55D, H.56A, H.56D Made in USA. 35,000 RPM Max Speed Flame Inverted Cone Oval Tree Point Tree Radius Shape A-F-1 A-IC-1 A-IC-2 A-OV-1A-OV-2 A-TP-1 A-TP-2 A-TP-3 A-TR-2 A-TR-3 Part No. 1/8 1/8 1/4 1/81/4 1/81/8 1/4 1/8 1/4 Head Dia.″ 1/4 3/161/4 7/323/8 1/43/81/2 1/21/2 Head Length″ 1-17/32 1-1/21-13/16 1-17/32 1-29/32 1-1/21-1/22-1/32 1-1/22-1/32 Overall Length″ $10.40 $10.40 $14.70 $10.40$14.70 $10.40$10.40 $14.70 $10.40 $14.70 Price Each Aluminum Oxide (Red) $2.60 Ea Miniature Carbide Burs A-RA1A-RA3A-RA11A-RA12A-RA21 Part No. 1/85/321/43/161/4Head Dia.″ 1/49/327/643/165/16 Head Lgth″ 120120120100120 Grit 2.35mm (3/32″) Shank, 1-3/4″ Overall Length $4.50 Ea (except A-TR-5C $10.40) New New New New New New Silicon Carbide (Green) $2.60 Ea A-RA31A-RA33 A-RA41A-RA42 A-RA51 Part No. 1/85/32 1/43/16 1/4Head Dia.″ Head Lgth″ 1/4 9/327/643/165/16 Grit 150150 150120 150 New Ball A-RA11R 2.8 2.8 Ball Ball Inv Cone A-RA2 A-RA4 A-RA5 1.0 2.1 2.1 1.0 2.1 2.0 Ball Taper Inverted Cone Shape A-212 A-215 A217 A-201*A-220 A-230 A-202*A-203* A-208* A-240 Part No. .2 .5 .7 .79 1.0 2.1 2.351.19 1.62.35 Head Dia. mm .2 .4.5 .5.8 1.92.14.37 1.61.6 Head Length mm Cross Cut VanadiumTungsten Steel $1.30 Ea Carbide $4.50 Ea Always Wear Eye Protection While Using Rotary Power Tool Accessories 22 Ball Cone Cylinder Square Cylinder Radius Shape A-B-1 A-B-2 A-CO-2 A-CO-3 A-CP-1 A-CP-2 A-CP-3 A-CR-1A-CR-2 A-CR-3 Part No. 1/81/4 1/81/43/321/81/4 3/321/8 1/4 Head Dia.″ 1/81/4 5/85/87/169/161/2 7/16 9/161/2 Head Length″ 1-17/321-3/4 1-1/22-3/16 1-1/2 1-1/22-1/16 1-1/21-1/2 2-1/16 Overall Length″ $10.40$14.70 $10.40$14.70 $10.40 $10.40$14.70 $10.40$10.40 $14.70 Price Each Cross Cut * Asterisk indicates burs included in Kit AK200. Cylinder Ball Nose Tree Point Shape A-204* A-207* A-205* A-206*A-TR-5CPart No. 1.6 1.6 1.19 1.62.35 Head Dia. mm 4.37 4.37 3.97 3.97 6.35 Head Length mm AK200 $31.70 8-Pc Kit Miniature Carbides 2.35mm shanks One each of A-201, A-202, A-203, A-204, A-205, A-206, A-207, A-208 shown with *. AK210 $59 14-Pc Kit Miniature Carbides 2.35mm shanks Shape Part No. Head Dia. mm Head Lgth mm Part Numbers and Prices are shown in red on each page. One each of all miniature carbides except does NOT include A-TR-5C. Comes in small round bur stand. Always Wear Eye Protection While Using Rotary Power Tool Accessories 23 Tungsten Carbide Burs 2.35mm and 1/8″ Shanks Made in USA. 35,000 RPM Maximum Speed ® Typhoons have unique structurally aligned tungsten carbide points that last long and do not load quickly. Use the fine grits for general shaping and sanding. The coarse grit is for even more rapid and aggressive shaping and roughing out work. Typhoons are ideal for use on hard and soft woods, acrylic, die stone, plaster, hard rubber and fiberglass. 2.35mm (3/32″) Shank Fine (Blue) Grit Individual Burs $16 Ea AKHK83 $40.00 3-Pc Typhoon Kit Tungsten Carbide Burs 1/4″ and 6mm Shanks ® Made in USA. 25,000 RPM Max Speed for burs with heads less than 13/16″ (21mm) in diameter and 10,000 RPM for burs with head diameters 13/16″ (21mm) or larger. 1/4″ (6.4mm) Shank Coarse (Red) and Fine (Blue) Grits. Priced Below 2.35mm (3/32″) shanks Contains: A-KB32119, A-KB32719, A-KB32913 Ball Long Taper Taper Cylinder Ball Nose Flame Bud Shape 5/163/167/165/165/16 5/165/16 Head Dia.″ 5/16 3/45/81/21/2 1/23/4 Head Length″ A-KB32315 A-KB32119A-KB32915A-KB32519A-KB32719 A-KB32913A-KB32415Fine Part No. Ball Nose 5/16 1-3⁄4 A-KB14714 A-KB14715 $18.50 Ball Nose 13/16 1-1⁄4 Ball Nose 9/16 3/4 Flame 7/8 1-3⁄8 Flame 5/8 1-1⁄16 A-KB14734 A-KB14735 $20.00 A-KB14712 A-KB14713 $18.50 A-KB14978 A-KB14979 $21.00 A-KB14958 N/A $20.00 Flame 3/8 3/4 A-KB14912 Coarse Part No. A-KB14913 Fine Part No. Price Each $17.50 Part Numbers and Prices are shown in red on each page. Smooth End 1/8″ (3.18mm) Shank Coarse (Red) and Fine (Blue) Grits Individual Burs $16 Ea Shape Ball Ball Long Taper Taper Bud Ball Nose Ball Nose 5/167/16 3/16 5/16 5/163/165/16 Head Dia.″ 5/16 7/16 3/4 1/2 3/4 7/8 1/2 Head Length″ A -KB18314A-KB18338A-KB18118A-KB18114 A-KB18414A-KB18718A-KB18714 Coarse Part No. A-KB18315A-KB18339A-KB18119A-KB18115 A-KB18415A-KB18719A-KB18715 Fine Part No. Smooth End Rotor Saw 11/16 3/16 Flame 7/16 5/8 Dove Tail 7/16 1/2 Cylinder 5/16 1/2 Cylinder 5/16 1/2 Shape Head Dia.″ Head Length″ A-KB18834 A-KB18914 A-KB18638 A-KB18514 A-KB18524 Coarse Part No. A-KB18835 A-KB18915 A-KB18639 A-KB18515A-KB18525 Fine Part No. A-HB58 $4.10 Brass Brush Overall Dimensions–5/8″ wide x 5-3⁄4″ long. Bristles–3/8″ wide x 1-3⁄4″ long x 5/8″ high. Typhoon Burs, Sanding Sleeves, and Discs are easy to clean with the A-HB58 Brass Brush. It removes dust or chips from between rows of carbide points. Caution–Do not use a file card or steel brush to clean Typhoon burs and sleeves. Always Wear Eye Protection While Using Rotary Power Tool Accessories 24 Ball 7/8 7/8 Ball 9/16 9/16 Taper 15º 5/16 1-1⁄2 Taper 15º 13/16 1-3⁄8 Taper 15º 9/16 1 A-KB14395 A-KB14312 A-KB14114 A-KB14178 N/A A-KB14313 A-KB14115 A-KB14179 $25.00 $18.50 $18.50 $20.00 Smooth End Taper 5º 13/16 (9/16) 1-1⁄4 A-KB14158 A-KB14198 A-KB14159 N/A $18.50$20.00 Shape Head Dia.″ Head Length″ Coarse Part No. Fine Part No. Price Each 1/4″ & 6mm Shank Sanding Sleeves Priced Below AKHK84 $55.00 4-Pc Typhoon Kit 1/8″ (3.18mm) shanks Contains: A-KB18119, A-KB18834, A-KB18414, A-KB18715 Shape Head Dia.″ Head Length″ Made in USA. 10,000 RPM Max Speed for use on Foredom’s BL and other Bench Lathes. Cylinder 13/16 1-1⁄4 Cylinder Cylinder Shape 9/16 9/16Head Dia.″ 1-1⁄4 3⁄4 Head Length″ Part No. A-KB14534 N/AA-KB14522 Coarse Fine A-KB14535 A-KB14533 N/A Part No. $20.00 $18.50$18.50 Price Each Expert carver, Frank Russell, uses smooth end cylinder to shape side to side without cutting into the area above the bur. Shank Size Grit Outer Dia. Inside Sleeve Only Dia Length Part No. Use on Mandrel Mounted Part No. 1⁄4″ Coarse15/16″3/4″1/2″ A-KB43524 A-SD143 A-KB43525 $16.00 $18.00 1⁄4″ Fine15/16″3/4″1/2″ A-KB43521 A-SD143 A-KB43522 $16.00 $18.00 1⁄4″ Coarse15/16″3/4″1″ A-KB43544 A-SD144 A-KB43545 $23.50 $26.50 6mm Coarse 24mm 19mm 25mmA-KB43544 A-SD662 A-KB43546 $23.50 $31.00 Always Wear Eye Protection While Using Rotary Power Tool Accessories 25 Angle Grinder Accessories–NEW 2″ Wheels Angle Grinder Accessories–NEW 2″ Accessories Foredom’s new 2″ Angle Grinder attachment for the H.30, H.30H and H.30SJ handpieces is especially versatile because of all of the accessories we’ve added for polishing, grinding, and sanding on virtually any material– metal, wood, stone, acrylic, ceramics, bondo, composites, resin, fiberglass, rubber and more. The accessories featured on this and the next 3 pages have special mounting hubs and mandrels and should NOT be mounted directly in a flexible shaft or micromotor handpiece. Part Numbers and Prices are shown in red on each page. ® 1 234 Flat Face Round Face Round Face Discs 3. A-KB25628 Coarse 4. A-KB25629 Fine with 3/8” Arbor Holes $4.80 Ea* Made in USA Use Aluminum Oxide on high tensile, tough materials including stone, porcelain, glass, and steel. A-10054 Cup Wheel for medium to fine finishing. A-10062 Tapered Wheel for med. to fine finishing. A-10063 Wheel for extremely fine cutting. A-10068 Silicon Carbide for grinding, rough finishing, deburring, smoothing, cleaning low-tensile, brittle or “smeary” type materials such as aluminum, brass, stainless steel, glass, stone, and non-metals. CeramCut Blue Wheels A-10064 and A-10065 (Cup Shape) last 3 to 5 times longer and removes material faster. Can be used on hardened and mild steel, steel alloys, chrome cobalt, titanium, platinum, other ferrous metals and wood. Mount with A-69212L Long Hub 6-Pk of Discs Mount with A-69212 Short and A-69212L Long Hubs 1 Ted Knapp, carpenter and woodcarver, uses a Typhoon Disc to hollow out a decoy. Aluminum Oxides 1 A-10054 Cup 2″ Abrasive Flap, Cut Off, Felt and Unitized Wheels with 3/8” Arbor Holes Priced Below Flap Wheels are made from aluminum oxide mineral and are used for fast clean-up and pre-polishing work. 10,000 RPM Max Speed. Fiberglass Reinforced Cut-Off Wheels are used to cut off, groove, & trim metal, wood, and ceramics. 2″ x 3/64″ thick, 60 grit, 30,000 RPM Max Speed. Hard Density Felt Wheels are made from tightly compressed, top quality wool felt. They hold an edge for working in angles and corners and are used with polishing compounds for polishing and lapping on metals, plastics, wood and more. 20,000 RPM Max Speed. Additional sizes of felt accessories for use in handpieces are on pg 16. The Unitized Wheel is ideal for deburring, oxide and fire scale removal, cleaning, blending & smoothing. Made of non-woven fiber coated in aluminum oxide. Should ONLY be used dry. 30,000 RPM Max Speed. Unitized Wheel Cut Off Wheel Felt Wheels Knife EdgeSquare Edge Cup Mount with A-69212 Short Hub Mount with A-69212L Long Hub Always Wear Eye Protection While Using Rotary Power Tool Accessories 26 1 A-4542-680/yellow 2 A-4543-6 120/white 3 A-4544-6 220/red 4 A-4545-6 5 A-4546-6 400/blue Pumice 1,200/pink 6 Micron 3,000/peach 7 A-4548-6 1 Micron 14,000/light green 2 3456 7 Assortment Kits See individual accessory listings for max. speed. Grit 150 2 A-10062 Taper 120 Use on Edge not Flat side 3 A-10063 400 Use on Edge not Flat side Silicon Carbide Grit 4 A-10068 100 Use on Edge not Flat side CeramCut Blue Stones 5 A-10064 120 Use on Edge not Flat side 5/8″w, 1/2″ thick cup working face 12 345 6 Grit/Color 6 A-4547-6 6 A-10065 (* $8.50) 100 Flap Wheels 3M Scotch-Brite Radial Bristle Discs are molded plastic discs embedded with 3M Cubitron™ and aluminum oxide mineral. The abrasive filled bristles apply a continuous fresh supply of mineral eliminating the need for compounds. Their flexible bristles reach into grooves and contours. Clean and remove dirt, rust, and oxidation without damage to the underlying surface. Varying the speed allows you to obtain different finishes. Mount 1-2 discs on Short Hub and 3-4 on Long Hub. Other size discs available for use in handpieces. See pages 14 & 15. Made in USA. 10,000 RPM Max Speed 2″ Abrasive Wheels with 3/8” Arbor Holes $20.80 per 6-Pk 2″ Tungsten Carbide Discs with 3/8” Arbor Holes $38 Ea Typhoons have unique structurally aligned tungsten carbide points that last long and do not load quickly. Use the fine grits for general shaping and sanding and the coarse grit for more rapid and aggressive shaping and roughing out work. Ideal for hard and soft woods, acrylic, die stone, plaster, hard rubber and fiberglass. Mount with A-69212 Short Hub Flat Face Discs 1. A-KB25626 Coarse 2. A-KB25627 Fine 2″ Scotch-Brite™ Radial Bristle Discs Made in USA. 30,000 RPM Max Speed 15,000 RPM Max Speed Flap Wheels $2.20 Ea $9.80/5-Pk Grit A-2201A-2201-5 60 A-2202A-2202-5 120 A-2203 A-2203-5 240 A-2204A-2204-5 320 A-2205A-2205-5 600 AK2200 $ 9.80 A ssortment 5-Pk One of each grit Fiberglass Cut Off Wheel A-D11 $1.8060 Knife Edge Felt Wheel A-KE6 $5.60Hard Square Edge Felt Cup Wheel 1-7/8″ dia., 3/4″ thick, 1/2″ from arbor hole to edge ARFWAGSE $15.50Hard Unitized Wheel A-10055 $9.60 1/4″ thick AK6901 $78.00 Stone Carving Kit, 20-Pc AK6903 $79.00 AK6905 $57.00 Typhoon Carbide Disc A-KB25628, CeramCut Blue Wheel A-10064, Scotch-Brite Radial Bristle 80-Grit Discs A-4542-6, 5 ea of Aluminum Oxide Sanding Discs A-5632-5, A-5633-5, A-5634-5, A-5635-5, Abranet Sanding Screen Kit AK10030, 25 PSA Velcro Discs A-10041, 2 Disc Protector Pads A-10042. Square Edge Felt Buff ARFWAGSE, Silicon Carbide Wheel A-10068, Aluminum Oxide Wheel A-10063, Abranet Sanding Screen Kit AK10030, 2 Disc Protector Pads A-10042, 1-oz Platinum White Polishing Compound A-40061, 5 ea of Imperial Microfinishing Discs A-4591, A-4592, A-4593, A-4594, A-4596, A-4598, 2 Cut Off Wheels A-D11, 30 PSA Velcro Discs A-10041. Woodcarving Kit, 60-Pc Metal Working Kit, 73-Pc 1″ & 2″ Quick Change Sanding Discs– 1″ $3.50/10-Pk Flexible Diamond Disc A-5752, Diamond Microfinishing Discs A-4452, A-4453, A-4454, A-4455, A-4456, A-4457, A-4583. 2 Cerium Oxide Discs A-4408, 10 PSA Velcro Discs A-10041. 10,000 RPM Max. Speed 2″ $5.25/10-Pk Quick Change Sanding Discs are made of economical aluminum oxide grain and have a slotted, hard plastic backing. The 2″ size disc overhangs the plastic backing and offers excellent flexibility for sanding contours. This style disc REQUIRES the use of a A-69223 Quick Change Arbor with Cross Bar that mounts onto the Angle Grinder. Once the arbor is installed, it is quick and easy to make grit changes. 10-Packs of 1″ and 2″ diameters Discs come in 5 different grits. Mount with A-69223 Quick Quick Change Arbor Change Arbor with Cross Bar 15,000 RPM with Cross Bar 1″ Part No. 2″ Part No. Max Speed 10-Pk 10-Pk Grit A-2241-10 A-2261-10 60 Slotted A-69223 $5.00 Disc Back A-2242-10 5 Grits A-2262-10 120 A-2243-10 A-2263-10 240 A-2244-10 A-2264-10 320 A-2245-10 A-2265-10 600 1″ Assortment AK2240 $3.50 (2 ea of 5 grits) 2″ Assortment AK2260 $5.25 (2 ea of 5 grits) Always Wear Eye Protection While Using Rotary Power Tool Accessories 27 NEW 2″ Angle Grinder Accessories Angle Grinder Accessories–2″ PSA Sanding Discs Made in USA. 10,000 RPM Max Speed Mounting Pressure Sensitive Adhesive (PSA) Sanding Discs on Angle Grinder– PSA Disc A-10041 has a Velcro Loop fabric surface that is REQUIRED to adhere all PSA 2″ sanding discs (featured on this and next page) to the Velcro Hook surface of Disc Mandrel A-69222 OR the Velcro Hook surface of Sanding Heads shown below. PSA Velcro Disc A-10041 insulates, prevents slippage, and permits reuse of sanding discs. Mounting directions: 1. Remove the protective backing from sticky side of white PSA Velcro Loop Disc A-10041 2. Remove backing from sticky side of PSA Sanding Disc (Flex DIamond, Ceramic Purple, Aluminum Oxide, etc). 3. Put sticky sides together and mount Velcro Loop white fabric side down onto Velcro Hook surface of Disc Mandrel A-69222 or Sanding Head below. Velcro Hook Surface Velcro Loop Side and PSA Sticky Side on Reverse with 3/8” Arbor Holes. Made in USA. 20,000 RPM Max Speed Priced Below 4 Also for use with Screw Mandrels A-M-30 and A-M31 on page 19 3M Ceramic Purple Abrasives are excellent for sanding and finishing wood, metals, fiberglass, diestone, plastics, and other materials. Its patented CubitronTM ceramic aluminum oxide mineral sharpens itself with use. Ceramic Purple discs last 2 to 4 times longer than traditional aluminum oxide and offer faster stock removal with less heat and loading. Other sizes of discs and bands are available for use in handpieces. See page 11. Made in USA. 10,000 RPM Max Speed 4 Grits Sanding Heads Price Ea Use 3M Cerium Oxide for achieving a final, high shine polish on gemstone, rock and glass. Discs should be used wet and results are also best when used after a 1,200–4,000 grit abrasive. See page 9 for other discs & bands for use in handpieces. 1 AR10043$10.50 Extra Firm, 3/16″ thick 2 AR10044$11.00 Firm, 5/16″ thick 4 AR10046$12.50 Soft, 5/8″ thick Individual10-Pack Part No. Part No. Grit A-5682 A-5682-10 60 A-5683 A-5683-10 80 Always Wear Eye Protection While Using Rotary Power Tool Accessories $19.30 120 125 A-5754 $16.40 220 74 A-5756 $16.40 400 40 A-5758 $16.4080020 5-Pack Part No. A-5632-5 10-Pack Part No. Grit A-5632-10 60 A-5633-5 A-5633-10 80 A-5634-5 A-5634-10 120 A-5635-5 A-5635-10 220 Assortment AK5630 $6.50 (2 each of four grits) Priced Below Great on Glass & Stone 1 2 3 Part No. A-4452 Each $4.50 Grit Micron 120 125 A-4453 $4.40 220 74 A-4454 $4.40 320 45 4 5 A-4455 $4.40 400 30 A-4456 $4.40 600 20 6 A-4457 $4.40 1,200 9 7 A-4583 $5.80 4,000 3 8 Cerium Oxide Polishing Disc: A-4408 $5.30 50,000 .5 $5/10-Pk, $22/50-Pk Use 3M Imperial Microfinishing Film PSA discs dry on metal and wet on stone. High strength polyester film backing coated with premium, micron graded aluminum oxide particles provides greater cutting efficiency and is resin bonded for increased durability. This fast-cutting abrasive provides gentle, contoured polishing. 10-Pk 50-Pk Part No. Part No. Grit / Micron 1 2 3 4 5 6 1 A-4591-10 A-4591-50 1,200 / 9 A-4592-10A-4592-50 600 / 15 2 A-4593-10A-4593-50 400 / 30 3 4 A-4594-10 A-4594-50 320 / 40 A-4596-10 A-4596-50 220 / 60 5 180 / 80 6A-4598-10 A-4598-50 2″ Abranet™ Sanding Screens with Velcro Loop Backing $5.80/5-Pk Velcro Hook Disc Mandrel or Velcro Hook Sanding Head 4 Grits A-5753 2″ Imperial Microfinishing Film PSA Sanding Discs 3 AR10045$11.50 Medium, 3/8″ thick Mount with A-10041 PSA Velcro Loop Disc & A-69222 $4.30 per 5-Pk, $8.00 per 10-Pk 28 $5.30 Ea A-5684 A-5684-10 120 A-5685 A-5685-10 220 Assortment AK5680 $4.00 (1 each of four grits) 2″ Aluminum Oxide PSA Sanding Discs 3M Aluminum oxide sanding discs are made of high-grade mineral and a bonding system which reduces shelling of the mineral. These economical abrasives are excellent for fast clean-up and pre-polishing work. Other sizes of discs and bands are available for use in handpieces. See page 12. 2″ Cerium Oxide Polishing Disc Photo courtesy of www.jadecarver.com 2 2″ Ceramic Purple PSA Sanding Discs $1.20 Ea, $10.70/10-Pk Grit Micron 60250 3M’s Diamond Micro Finishing PSA discs have flexible film backing suitable for metal and lapidary applications. They work great on all materials including stone, glass and hard to work on stainless steel and titanium. Use wet when working with gemstone, rock and glass. Bands and a smaller disc also available for use in handpieces. See page 10. IndividualPrice Using AR10046 Sanding Head with PSA Flex Diamond psa disc on California Jade. Mount with A-10041 PSA Velcro Loop Disc & A-69212L Long Hub 3 5 Grits IndividualPrice Part No. Each A-5752 $22.70 2″ Diamond Microfinishing Film PSA Sanding Discs 2″ Velcro Hook Sanding Heads 1 3M Flexible Diamond PSA discs are made from a 2-ply polyester backing film evenly coated with diamond filled nickel plated dots. Grind, sand, and smooth wet or dry on glass, carbide, composites, plastic, enamels, stone, steel, exotic alloys, gypsum, ceramics, wood, bone, chrome cobalt, painted or plated surfaces. Use wet when working with gemstone, rock and glass. Bands also available for use in handpieces. See page 9. PSA Velcro Loop Backed Discs: A-10041-5 (5-Pk) $4.00 A-10041-25 (25-Pk) $15.00 Sanding Heads can vary the firmness or softness of the pressure from an abrasive disc. Use a PSA Velcro Loop Disc A-10041 to attach actual sanding discs to these heads. The Velcro sanding heads have a velcro hook surface and mount onto the Angle Grinder with A-69212L Long Hub. Heads can also be used with A-10042 Disc Holder Protector Pad with Sanding Screens, see below and with items on this and next page. Velcro Hook Disc Mandrel or Velcro Hook Sanding Head 2″ Flexible Diamond PSA Sanding Discs Velcro Hook Backed Disc Mandrel (screws onto Angle Grinder): A-69222 (Ea) $5.00 Mount with A-10041 PSA Velcro Loop Disc & A-69222 Aluminum oxide grain abrasive coating bonded to unique, durable, open construction polyamide fabric for uniform sanding. Screens have Velcro Loop backing and MUST be used with A-10042 Disc Holder Protector Pad on Velcro Hook Disc Mandrel A-69222 or with Velcro Hook Sanding Heads. Tap or blow screens out to clean dust from sanding. Will not clog, even on wet or green wood. A-10042 Disc Abranet Screens Holder Protector Disc Holder Protector Pads: Screens 5-Pack Part No. Grit A-10042 (Ea) $3.00 A-10042-5 (5-Pk) $14.00 Pad & A-69222 in 5 Grits A-10032-5 80 Disc Mandrel This orange-colored velcro pad forms a secure A-10033-5 120 connection between the Abranet sanding screen A-10034-5 180 and the disc mandrel. It prevents overheating & clogging. Using one for each grit is recommended A-10035-5 240 to prolong the life of the Abranet Screens. Use A-10036-5 320 orange side on the Abranet Screen back and white Assortment AK10030 Made in USA. side for Velcro Hook Disc Mandrel or Velcro Hook 15,000 RPM Max Speed $5.80 (1 ea of five grits) Sanding Head. Always Wear Eye Protection While Using Rotary Power Tool Accessories 29 Assortment Kits General Use in this Column AK20 $43 35-Pc Kit 3/32″ & 1/8″ Shanks Total Value Over $56 35-pc assortment contains steel cutters and burs, mounted points, wire and bristle brushes, rubber bonded abrasives, sanding drums and felt bobs. 20,000 RPM Max Speed AK22 $299 Frank Russell Kit, 33-Pc These pre-sharpened, quality made steel chisels are for use in Foredom’s H.50 reciprocating chisel handpiece, at right, and other power chisel tools, including those from Proxxon and WeCheer. The cutters have 18mm long tangs and 55mm and 75mm overall lengths–from cutting edge to end of tang. Cutters in the A-KC500 Series are 55mm and those in the A-KC700 series are 75mm long. Priced below. 3/32″, 1/8″, 1/4″ Shanks Total Value Over $349 33-pc Kit contains the burs Frank Russell uses in his DVD, “Fur, Feathers and Fins”. According to Frank, these are the ones needed for any carving you can hold in your hand. Dominated by Foredom’s exclusive Typhoon® carbide burs in coarse and fine grit, the kit includes 13 Typhoons in 1/4″, 1/8″, and 3/32″ shank. 8 Ceramcut Blue Stones, 3 plated diamond, 1 vanadium steel cutter, 1 carbide bur, 3 ruby carvers, and sandpaper split mandrel. Also, 2″ fine bristle nylon brush with tapered mandrel and rotating bur and tool holder. 25,000 RPM Max Speed, 10,000 RPM on 1/4″ Typhoons. AK21 $134.40 88-Pc Kit AK23 $170 Frank Russell Basic Kit, 22-Pc 3/32″ & 1/8″ Shanks 3/32″, 1/8″, 1/4″ Shanks. Total Value Over $176 Total Value Over $143 88-pc. assortment comes packed in our General Applications Kit K.2272. Assortment contains some of our most unique rotary accessories: Ceramic Purple Abrasive Bands, V Stone Mounted Abrasives, and CeramCut Blue Stones. Also plated diamond points, steel cutters, aluminum oxide points, rubber bonded abrasive wheels, wire and bristle brushes, felt buffs and bobs, tube of red polishing rouge, various mandrels. 20,000 RPM Max Speed AK2446 $140 34-Pc Kit Chisels for Reciprocating Power Chisels Woodcarving 2,500 – 10,000 RPM Recommended Operating Speed 34-pc assortment contains accessories for smoothing and polishing metal, wood, plastic, and acrylic. Includes a coarse grit Typhoon bur for fast stock removal, 6 ea of 3M’s Scotch-Brite Radial Bristle 3″ Discs in 80, 220, 400, and 14,000 grit for smoothing, 2– 2″ cotton buffs and tubes of Platinum White and Platinum Blue compound for polishing. Also, 4 flat head and a screw mandrel with 1/4″ shanks for mounting the discs and buffs. AKHK10 $36 10-Pc Kit 1/8″ Shanks Total Value Over $40 10-pc assortment includes mounted abrasive aluminum oxide and silicon carbide points, carbide burs, felt bobs, sanding drum and band, 2 mandrels. 20,000 RPM Max Speed We reserve the right to substitute comparable accessories when necessary. Non-Metal AK2442 $99 50-Pc Kit 1/8″ Shanks Total Value Over $113 50-pc assortment for use on wood, rubber, acrylic and other non-metal materials. Includes 2 coarse grit Typhoon burs for rapid stock removal, 2–1-1/2″ Cut Off Wheels, 3 ea. of 1/2″ x 1/2″ Ceramic Purple sanding bands in 60, 80, 120, & 220 grit, 6 ea. of Scotch-Brite Radial Bristle 1″ Discs in 36, 50, 80, & 120 grit for final shaping, and 1″ cotton buff and mounted felt bob for final polish. Also, 7–1/8″ shank mandrels and tube of Platinum Blue compound. 20,000 RPM Max Speed Dental Lab Fluteroni #3 and #7 Sweeps #1 x 9mm #1 x 14.5mm #2 x 9mm #2 x 14mm 8mm 12mm #3 x 9mm #3 x 14mm #7 x 8mm #7 x 13mm #7 x 17mm A-KC509A-KC511 A-KC510A-KC512 A-KC515 A-KC721 A-KC503A-KC501A-KC504A-KC502A-KC718 $7.50$9.50 $7.50$9.50 $9.50 $10.50 $7.50$9.50$7.50$9.50$10.50 5555 5555 55 75 5555555575 1, 3 2, 3 1, 3 4 3, 4 5 1, 3 2, 3 1, 3 2, 3 5 Comes in Sets Part No. Price Each Length mm #8, 9, 11 Sweeps 70º, 75º, 110º Parting Tools #8 x 10mm #9 x 9mm #9 x 6mm #9 x 14mm #11 x 3.5mm 70º x 5.5mm 70º x 8mm 75º x 12mm 110º x 7mm 110º x 11mm 110º x 16mm Part No. A-KC508 A-KC514A-KC517 A-KC723 A-KC505 A-KC506A-KC507 A-KC717 A-KC516 A-KC513 A-KC722 Price Each $9.50$9.50$7.50 $10.50$7.50 $7.50$9.50$10.50$7.50 $9.50$10.50 Length mm 55 5555 7555 555575555575 Comes in Sets 2, 3 4 4 5 1, 3 Chisel Sets Set 2 AKHK560 5-pc. $41 A-KC501, A-KC502, A-KC507, A-KC508, A-KC511 Set 3 AK510 12-pc. $79 A-KC501, A-KC502, A-KC503, A-KC504, A-KC505, A-KC506, A-KC507, A-KC508, A-KC509, A-KC510, A-KC511, A-KC515 in A-KC500 Canvas Pouch Total Value Over $134 Set 5 AKHK580 5-pc. $47 A-KC717, A-KC718, A-KC721, A-KC722, A-KC723 30-pc. kit for polishing Valplast®, Flexite®, and other nylon denture materials. The larger diameter accessories are for use on the tapered spindle of Foredom’s BL Lathe. Includes: 6-pks of 3″ Scotch-Brite Radial Bristle Discs in 80, 220, 14,000 grit. Also 3″ cotton buff, 2 right & 2 left side spindle adapters, and bar of platinum white polishing compound. 7,000 RPM Max Speed 12-Pc Chisel Set (AK510) comes packed in canvas pouch. Includes chisels in Set 3. A-KC500 $15 Pouch sold separately. Open Canvas Pouch measures 9-3⁄4″ x 7″. Folds to 4-3⁄4″ x 3-1⁄2″. 2, 3 5 4 4 5 Foredom’s Belt Sander Attachment mounts easily over the top of the H. 30 handpiece and is used to power sand and smooth metal, wood, acrylic and composite materials. The attachment includes a set of 10 belts that are also available separately as detailed below: Set 1 AKHK550 6-pc. $41 A-KC503, A-KC504, A-KC505, A-KC506, A-KC509, A-KC510 Set 4 AKHK570 6-pc. $47 A-KC512, A-KC513, A-KC514, A-KC515, A-KC516, A-KC517 1, 3 Replacement Sandpaper Belts for Belt Sander Attachment Sets 1, 2, 4, and 5 come packed in hanging plastic case. Set 3 comes in canvas pouch AK3361 $125 30-Pc Kit Always Wear Eye Protection While Using Rotary Power Tool Accessories 30 #2 Right Skews Single Bevel 22-pc Kit is a scaled down version of AK21 above. Includes 2–1/4″, 2–1/8″, and 1–3/32″ shank Typhoons, 7 Ceramcut Blue Stones, 4 plated diamonds, 3 ruby carvers and a steel cutter. Also, 2″ fine bristle nylon brush with tapered mandrel. 25,000 RPM Max Speed, 10,000 RPM on 1/4″ Typhoons. 1/4″ Shanks Total Value Over $152 #1 Chisels Single Bevel 9/32″ x 10-1/8″ Replacement Sandpaper Belts Coarse Grits A-797415 100 grit 5 Belts $3.50 A-797425 180 grit 5 Belts 3.50 A-797435 240 grit 5 Belts 3.50 AK797409 9 Belt Coarse Assortment 5.00 3 ea. of 100, 180 and 240 grit Fine Grits A-797445 320 grit 5 Belts $3.50 A-797455 600 grit 5 Belts 3.50 A-797465 1,000 grit 5 Belts 3.50 AK797429 9 Belt Fine Assortment 5.00 3 ea. of 320, 600 and 1,000 grit AK797230 Kit with Belt Sander Attachment and H.30 Handpiece, Chuck Key and 10 Belts. AK797439 18 Belt Coarse and Fine Assortment $10.00 with 3 ea. of ALL grits 100, 180, 240, 320, 600 and 1,000 grit Part Numbers and Prices are shown in red on each page. Always Wear Eye Protection While Using Rotary Power Tool Accessories 31 Our mission is to offer the best quality and selection of rotary accessories for accomplishing what you do best— whether you’re a jeweler, woodcarver, machine shop operator, custom manufacturer, fabricator, research scientist, lab technician, conservator, display designer, sculptor, artisan, crafter or home shop enthusiast. Our catalog features what you’ve come to expect from Foredom– a vast selection of items in different sizes, shapes and grits. Since quality is key, the majority of our accessories are made in the USA, and nearly all of the rest come from Switzerland, Germany, and Belgium. This new edition introduces 2″ discs and wheels for use with our new Angle Grinder Attachment and drilling accessories– some less popular items have been eliminated. Product Index New Items Shown in Red Page Abranet™ Sanding Screens. . . . . . . . . . . . . . . . . . . . . . . . . 29 Abrasive Cleaner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Abrasive Discs and Cut-Off Wheels . . . . . . . . . . . . . . . . . . . 7 Abrasive Wheels for use with BL Lathe . . . . . . . . . . . . . . . 13 Aluminum Oxide Grinding Stones . . . . . . . . . . . . . . . . . . . . 6 Aluminum Oxide Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Aluminum Oxide Sanding Bands and Discs– 3M. . . . . . . . 12 Angle Grinder Accessory Kits. . . . . . . . . . . . . . . . . . . . . . . 27 Anvil Points and other Hammer Tips . . . . . . . . . . . . . . . . . . 3 Assortment Kits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Brass Cleaning Brush. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3, 24 Brushes– Bristle, Steel, Brass, Wire, Nylon, Tampico. . . . . . 13 Buffs– Muslin, Cotton, Felt. . . . . . . . . . . . . . . . . . . . . . . 13, 17 Bur Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Carbide Burs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Carving Drills. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 CeramCut Blue Stones and Wheels . . . . . . . . . . . . . . . 4-5, 13 Ceramic Purple Sanding Bands and Discs– 3M . . . . . . . . . 11 Cerium Oxide Polishing Bands and Discs– 3M. . . . . . . . . . . 9 Chisels (Cutters–non rotary) . . . . . . . . . . . . . . . . . . . . . . . 31 Compounds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Cotton Buffs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Cut-Off Wheels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 CW Polishing Wheels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Diamond Hones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Diamond Points– Plated & Sintered. . . . . . . . . . . . . . . . . . . 8 Diamond Microfinishing Film Bands and Discs– 3M . . . . . 10 Diamond Twist Drills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Dressing Stone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Drills. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Dust Mask. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ear Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Felt Bobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Felt Buffs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Flap Wheels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 26 Flexible Diamond Sanding Bands and Discs– 3M. . . . . . . . . 9 Hammer Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 High Speed Steel Fluted Burs. . . . . . . . . . . . . . . . . . . . . . . 22 Imperial Microfinishing Film Discs– 3M. . . . . . . . . . . . . . . 10 Latch Type Abrasive Points. . . . . . . . . . . . . . . . . . . . . . . . . 22 Mandrels, Arbors, Chucks, Adapters. . . . . . . . . . . . . . . . 19-21 Plated Diamond Points and Discs. . . . . . . . . . . . . . . . . . . . . 8 Polishing Buffs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13, 17 Polishing Compounds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Quick Change Sanding Discs. . . . . . . . . . . . . . . . . . . . . . . 27 Radial Bristle Discs– 3M . . . . . . . . . . . . . . . . . . . . . . . . 14-15 Respirator– 3M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Rubber Bonded Abrasive Wheels. . . . . . . . . . . . . . . . . . . . . 7 Ruby Carvers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Safety Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Glasses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Sandpaper Belts for Belt Sander Attachment. . . . . . . . . . . 31 Satin Finishers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Scotch-BriteTM Radial Bristle Discs– 3M. . . . . . . . . . . . . 14-15 Screwdriver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Silicon Carbide Wheels. . . . . . . . . . . . . . . . . . . . . . . . . . 13, 26 Sintered Diamond Points and Discs. . . . . . . . . . . . . . . . . . . 8 Spindle Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Steel Carving Drills. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Steel Cutters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Steel Engraving Burs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Step Drills. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Tape– 3M Super Bond. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Typhoon® Tungsten Carbide Burs. . . . . . . . . . . . . . . . . . 24-25 Typhoon® Tungsten Carbide Sanding Sleeves. . . . . . . . . . . 25 Typhoon® Tungsten Carbide Wheels. . . . . . . . . . . . . . . . . . 26 Vetrap Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 V Stones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Vanadium Steel Cutters. . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Velcro Hook PSA Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Velcro Loop PSA Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Velcro Hook Sanding Heads. . . . . . . . . . . . . . . . . . . . . . . . 28 Wet/Dry Polishing Papers– 3M. . . . . . . . . . . . . . . . . . . . . . 22 Wet Stick. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3, 8 The Foredom Electric Company www.foredom.net 16 Stony Hill Road, Bethel, CT 06801 Tel: 203-792-8622 Fax: 203-796-7861 Email: customerservice@blackstoneind.com Accessory Catalog 350D Prices effective 8/1/11 and subject to change without notice.
Similar documents
Rotary Accessories
Plated Diamond Chamfer Points ream out drill holes and leave a smooth and rounded internal surface. They remove sharp edges that can cut bead string. For use on hardened steel, glass, precious meta...
More informationEMGS`s Gulf of Mexico multi
of Mexico Multi-Client datasets in the past year to develop plays, validate AVO ambiguities, interpret salt bodies and assess charge and seal risk. They used the knowledge gained from resistivity, ...
More information2013 PRODUCT CATALOG
With our knowledgeable employees and a fleet of multi-temperature trucks, Micucci Wholesale Foods has made a name for itself as the finest distributor of tomatoes, cheeses, pastas, oils, and meats ...
More informationExhibits - Olentangy Local School District
and/or teachers are facilitating average or typical growth for their students. We use both TerraNova and state achievement tests in Value-Added calculations. We are able to measure growth in third ...
More informationStadtlander Woodcarvings
A folding pocket knife with a single blade which locks in place while open. The D2 high carbon chromium tool steel has excellent edge-holding properties. Blade size is 1 9/16", handle size is 3 3/4...
More information