Chroma Modell 8700 | Batteriepackung ATS

Transcription

Chroma Modell 8700 | Batteriepackung ATS
Ihr Spezialist für
Mess- und Prüfgeräte
Battery Pack ATS
Model 8700
Battery Pack Production Flow Chart
KEY FEATURES
■ Specifically designed for battery production
line, or battery development testing
■ The application range of this system includes
battery modules for electric vehicles,
motor vehicles, and power storage systems
■ Increases QA efficiency by up to 80%
■ Inspection of BMS functions, connector
withstand voltage, consistency, and
performance of battery module
■ Charge/discharge power range : 5kW~500kW
Charge/discharge voltage range : 0V~1200V
Charge/discharge current range : 0A~2600A
■ Standard test items include insulation
resistance, electrical tests, software/
communication, and battery performance
testing
■ Able to create test fixture to connect the
customized battery module with the
automated switch control
■ The control system is an easy to use open
software platform that supports shop
floor control integration with Manufacturing
Execution System (MES)
Battery Cell/ Module/Pack Test Solutions
In order to increase testing coverage and the
efficiency of the power storage battery industry,
Chroma ATE has developed an automated
inspection system that can be applied to the
EOL (End Of Line) of battery pack production for
testing assembly defects, Battery Management
System (BMS) communication, internal power
switches, battery balancing circuits/consistency,
and temperature distribution, etc. before battery
packs are shipped out of the factory.
BMS PCBA Automated Test System
■ 2~32 series cell voltage simulation
■ Support active and passive balance test
■ Flexible hardware architecture that can select a variety of
hardware devices
■ The test items can be expanded to meet the demands for
inspecting tests.
■ Support dual-output of battery module
■ Resistor measurement (ID pin/NTC)
■ BMS IC Firmware program & Parameter download BMS
data compare
■ Support BMS interface: CANBus/RS485/RS232
■ Support BMS power consumption measurement
■ BMS IC V/I/T calibration
■ Over voltage protection test
■ Under voltage protection test
■ Over charge current protection test
■ Over discharge current protection test
■ Over temperature protection test
BMS PCBA ATS
The comprehensive PASS/FAIL tests can be used
in production lines, in a development phase
nearing completion and used during battery pack
acceptance inspection for EV or energy storage
station.
dataTec ▪ Ferdinand-Lassalle-Str. 52 ▪ 72770 Reutlingen ▪ Tel. 07121 / 51 50 50 ▪ Fax 07121 / 51 50 10 ▪ info@datatec.de ▪ www.datatec.de
Ihr Spezialist für
Mess- und Prüfgeräte
Battery Pack ATS
Model 8700
Video &
Color
Battery Module Automated Test System
■ Pass/Fail validation for battery module production
■ Inspection of BMS functions for voltage/
temperature measurement accuracy as well as
the distribution consistency of voltage/DC
resistance/temperature for each serial cell of
battery pack
■ Charge/discharge power range: 2.5kW~50kW
■ Charge/discharge voltage/current range:
0V~200V/0A~2600A
Flat Panel
LED/
Display Lighting
Optical
Devices
Battery Module ATS
Photovoltaic Test
& Automation
Battery Cell ATS
Automated
Optical Inspection
Architecture of Battery Pack Automated Test System
CAN Communication Test
■ Cell and Pack voltage/Temperature
■ Contactor characterization
■ Diagnostic trouble and fault mode test
Semiconductor/
IC
Isolation Test
■ Terminal(HV+, HV-) insulation
resistance
■ Ground isolation
■ Shield impedance
■ Hi-Pot test
Electrical Test
■ HV interlock function test
■ Max. and Min Voltage/Temperature
range test
Electrical
Safety
Performance Test
■ Standard charge/discharge
capacity test
■ Drive profile cycle test
■ DCIR / OCV test
Power
Battery Test &
Passive
Electronics Automation Component
Standard Function Test Items
PXI Test &
Measurement
* Please refer to Model 8000's specifications for detail instruments
Manufacturing
Execution System
A800027 : Test Fixture for Model 8000
A800068 : Digital Measurement Card
DC Load Module: Refer to 6310A, 63200, 6330A,63600 Series
Digital Power Meter : Refer to Model 66200 Series
AC Source : Refer to Model 6400, 6500, 61500, 61600, 61700, 61800 Series
DC Source : Refer to Model 62000H, 62000P Series
General
Purpose
Turnkey Test &
Automation
ORDERING INFORMATION
8700 : Battery Pack ATS
6011/80611/80614 : Timing/Noise Analyzer
6011N/80611N : Timing/Noise module
6012/80612 : Short Circuit/OVP Tester
6013/80613 : ON/OFF Controller
5004ATM : System Controller
A800003 : 8000 software Package
A800004 : 19" Rack for Model 8000
A800005 : PCI BUS GPIB Card (National Instrument)
dataTec ▪ Ferdinand-Lassalle-Str. 52 ▪ 72770 Reutlingen ▪ Tel. 07121 / 51 50 50 ▪ Fax 07121 / 51 50 10 ▪ info@datatec.de ▪ www.datatec.de
Änderungen und Irrtümer vorbehalten. dataTec 09-03-2016 | Update CHROMA ATE INC.: 02-2016
Battery Cell Automated Test System
■ Pass/fail validation for battery cell
production
■ OCV, ACIR and DCIR measurement
for multi-channels
■ Charge/discharge power range :
100W~400W
■ Charge/discharge voltage/current
range: 0V~80V/0A~80A

Similar documents