IP Gateway

IP Gateway
60.IP.GWAY.24V.DC[868]-[902]
Where applicable the original Certificates of Compliance are held at
Pressac’s business address, with copies being available on request.
PRODUCT SPECIFICATION
Power supply
Nottingham, May 2014
Pressac Communications
Robert Smith
145 Glaisdale Drive West
Technical Director
Nottingham
Mounting
Pressac Communications
NG8 4GY
Transceiver
FCC DECLARATION
Repeater
IP Gateway, IP Gateway - 902.875 MHz::
Environment
Contains FCC ID: SZV-STM300U
Operating Temperature
Contains IC: 5713A-STM300U
Frequency
Contient le module d’émission IC: 5713A-STM300U
Dimensions
The enclosed device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (i) this device may not cause
harmful interference and (ii) this device must accept any interference
received, including interference that may cause undesired operation.
DISPOSAL INSTRUCTIONS
The symbol shown here, and on the product, means that this product is
classed as electrical or electronic equipment, and should not be disposed
of with other household or commercial waste at the end of its working life.
The Waste Electrical and Electronic Equipment (WEEE)
Directive (2002/96/EC) has been put in place to recycle
products using the best available recovery and recycling
techniques to minimise the impact on the environment, treat
any hazardous substances, and avoid landfill disposal.
Typical 24V @ 50mA
Min Voltage 20V DC
Max Voltage 28V DC
4. Once the Gateway is discovered, please follow the onscreen instructions
and add the IP network settings. A default host name is assigned by
Pressac, but this can be altered if desired or if more than one IP Gateway
will be assigned to a network and there is a duplicate name.
DIN Rail
All EEP Telegrams
No
IP 40
0 to 50ºC
868, 902 MHz
95mm x 36mm x 58mm approx
Ethernet speed
10/100Mbps
WIRELESS GUIDELINES
In typical building conditions, where there are no obstructions causing
screening, EnOcean® devices will normally interoperate at a range of
30m line of sight (LoS)
Typically in a building, there are a number of factors which can reduce
this LoS range further.
Furthermore, the angle at which radio waves penetrate obstructions also
has a greater or lesser effect on signal quality. Where an obstacle to
transmission is present, the signal should propagate perpendicular to the
obstruction for best results.
5. Click on the “server configuration” tab in the utility and add the receiving
IP address and socket, or use DHCP to automatically assign an IP
address. The Gateway acts as a TCP client and connects to listening
servers on the specified socket and IP address.
TECHNICAL SUPPORT
Tel: +44 (0) 115 936 5238
E-mail: tech_support@presscomm.co.uk
The Pressac website www.presscomm.co.uk has further information on
our company, services and products.
CONTACT DETAILS
USER INSTRUCTIONS
Address as shown within the declaration of conformity.
Material reduction vs. LoS
Range
Wood, drywall, glass (uncoated with no metal)
0-10%
Brick, plasterboard
Set Up & Configuration
Tel: +44 (0) 115 936 5200
IP Gateway
Fax: +44 (0) 115 936 5252
868/902
E-mail: sales@presscomm.co.uk
PRODUCT DESCRIPTION
PRODUCT OPERATION
This Pressac Sensing IP Gateway can support 100s of EnOcean®
wireless devices. It provides bidirectional monitoring and control of
EnOcean® networks from IP network servers and devices, locally or
remotely. Pressac Sensing can also provide a fully managed web
platform.
Mount the IP Gateway in its desired location, away from any objects that
might obstruct the radio signal or reduce its range. The unit can be DIN rail
mounted using the clips on the base of the case.
KEY FEATURES & BENEFITS






Transforms your sensors into “Smart Internet Sensors”
®
Fully EnOcean compliant
Provides bi-directional network communications
Dedicated TCP Socket communications
Wide range 12-28V DC supply
Cost-effective enabler to integrate building/plant processes with
enterprise software
DECLARATION OF CONFORMITY
Pressac Communications Limited (the original
manufacturer) declares that the product branded
IP Gateway—868 MHz
If mounting in a control panel, make sure the panel box is plastic so that the
radio signal can travel through it. If mounting in a metal box the aerial must
be removed and connected outside the panel with a 50ohm coax lead.
Please note that the connector type is RP SMA (reverse polarity).
Do not over-tighten the aerial as it may cause damage.
Always use the approved aerial provided with the unit. Fitting a more
powerful aerial will cause the IP Gateway signals to travel further than
designed. This will invalidate the warranty and may be contrary to the radio
licence in your country.
Connect the IP Gateway to the Ethernet using a CAT5e or CAT6 cable and
connect the IP Gateway to a 100mA, 24V dc power supply.
When the IP Gateway is connected to the server, the Status LED will flash
for half a second every time EnOcean® radio telegrams are received by the
device.
PRODUCT MAINTENANCE
IP Gateway—902 MHz
satisfies the requirements of Annex II of the R&TTE Directive and has
been independently tested & found compliant with the essential
requirements of:
BS EN 61326-1 2013 Electromagnetic Compatibility
BS EN 61010-1 2010 Safety Requirements for Electrical Equipment
for measurement, control, and laboratory use Class B device
for industrial use, pollution degree II.
On receipt of the product, inspect it carefully to ensure no damage has
occurred during shipment. If damage is evident, or the product fails to
operate according to specifications, contact your dealer, or Pressac. If the
product appears to be malfunctioning, contact your dealer, or Pressac. The
Pressac website contains full information on our Product Returns Policy.
5-35%
Metal, concrete, mirrors
10-90%
Learn button
LEDs
1. Download and install the Gateway
Configuration Utility from
www.presscomm.co.uk/Pressac-sensingproducts
2. To configure the IP Gateway, power the IP
Gateway and connect your Windows PC directly
using an Ethernet cable. Ensure the LAN adapter
being used is enabled and all other network
adapters (including wireless) are disabled.
3. Open the installed
Pressac Ethernet Gateway Configuration Tool
and click “search” to begin searching for the connected Gateway.
6. Once fully configured, click on the “save” tab. The Gateway device is now
ready for use. Factory default network and connection settings are
restored by pressing the “learn” button while the unit is power cycled and
keeping it depressed for 12 seconds. While factory default settings are
being restored, the unit status LED will flash. When default settings have
been fully restored both LEDs will flash. This can be done standalone
without the Ethernet cable connected.