DRAFT PRODUCT CERTIFICATION MANUAL FOR COMMENTS Our Ref.: NRO/PRBO

DRAFT PRODUCT CERTIFICATION MANUAL FOR COMMENTS
Our Ref.: NRO/PRBO
13 Jan 2014
Please find enclosed the following draft certification manual:
Product manual on Room Heater as per IS 302-2-30 : 2007
Kindly examine the draft product certification manual and forward your comments on the
draft manuals.
Last date for comments: 28 Jan 2014.
Comments, if any, may please be made in the format as given below and mailed to PRBO at
the following email id: nlbo@bis.org.in.
Sl.
No.
Name
of RO /
BO
Clause/
Sub-clause
Paragraph /
Figure /
Table
Type of
comment
(General /
Technical /
Editorial)
Comments
Proposed Change
Note: Separate sheets may be attached in case comments are lengthy and cannot be
incorporated in the table.
For BIS Use Only
Doc No.: SM/IS 302-2-30-2007
Date of Issue: January 2014
PRODUCT MANUAL
FOR
Room Heater
(First Issue)
BUREAU OF INDIAN STANDARDS
MANAK BHAVAN, 9, BAHADUR SHAH ZAFAR MARG,
NEW DELHI – 110002
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC- 302-2-
30-2007
ISSUE: 01
PRODUCT MANUAL
DATE: NOV 2013
PREPARED BY:
PAGE: 1 OF 4
APPROVED BY:
AMENDMENT SHEET
To ensure that each copy of the Manual contains a complete record of Amendments, this
Amendment Sheet should be updated for each revised/new pages of the Manual. While
issuing any amendment, an acknowledgment slip will be included for signatures and return
by all Controlled Copy holders.
DISCARD
AMENDMENT
No.
Section
Page
Issue
No.
INSERT
Date
Section
Page
Issue
No.
SUMMARY
OF
CHANGE
Date
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
ISSUE: 01
DATE: NOV 2013
PREPARED BY:
PRODUCT MANUAL
PAGE: 4 OF 4
APPROVED BY:
FOREWORD
Electric room heater is an household appliance usually used in winter season to make the
room or space warm up to get rid of severe cold. Keeping in view the safety concern , these
products has been covered under mandatory certification w.e.f Sep.2009 under IS :302-230:2007.
This manual has been prepared in order to provide guidelines for processing of application
& operation licences in uniform manner
TABLE OF CONTENTS
Sections
Title
Section 1
Product Description
1.1
Description of product(s)
1.2
Latest Indian Standard Number with product title and number
of amendments
1.3
List of referred standards
1.4
Checklist for submission of an application for grant of licence
Section 2
Raw materials/ Components
2.1
List of important raw materials/components
Section 3
Manufacturing process and In-process Quality controls
3.1
Description of manufacturing process(es)
3.2
Infrastructure for production
Section 4
Certification criteria
4.1
Identification of critical requirements
4.2
Scheme of testing and inspection
4.3
Marking fee rates
4.4
Grouping guidelines
4.5
Guidelines for scope of licence
4.6
Guidelines for inclusion of new varieties
4.7
Sample size and Guidelines for drawl of separate samples
4.8
Manner of sealing of sample(s)
4.9
Dealing with sample remnants
4.10
Procedure for destruction of non conforming product
Section 5
Inspection and testing
Page No.
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
ISSUE: 01
PREPARED BY:
DATE: NOV 2013
APPROVED BY:
5.1
Packaging material requirement
5.2
List of test equipment/ facilities
5.3
Test facilities in BIS Labs/ OSLs with testing charges and
approximate time
5.4
Basis of grant of licence
5.5
Details of tests to be carried out in the factory
Annexes
Annexure – 1
PRODUCT MANUAL
PAGE: 4 OF 4
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
PREPARED BY:
ISSUE: 01
DATE: NOV 2013
PRODUCT MANUAL
PAGE: 2 OF 4
APPROVED BY:
SECTION 1: PRODUCT DESCRIPTION This standard recognizes the Indian
accepted level of protection against hazards such as electrical, mechanical, thermal ,fire &
radiation when operated as in normal use taking in to account the manufacturer’s
instruction. It also covers abnormal situations that can be expected in practice. It deals with
the safety of electric room heater for household & similar purposes ,rated voltage being not
more than 250 V for single Phase appliances and 415 V for other appliances.
Broad categories of Room Heater which are commonly used & covered under this standard
are :
Convector heaters:In convection heaters, heating elements either warm the air directly or heat oil or
another filler, or assisted by fan which in turn transfers heat to the air in Room or Space .
Radiative heaters: In Radiant Heater ,heating Element is wound on Ceramic rod or is encapsulated
in heat-resistant quartz/glass tubes, mounted in front of a metal reflector in a metallic or nonmetallic body. The heating element of liquid filled radiator heat up the oil or another filler which in
turn warm up the metallic fin that transfer heat .
Safety Concern : The risk of fire from electric heaters may be mitigated by low surface temperatures
(as found on oil-filled convective/Radiant heaters), or by switches that cut power in the event of the
device being knocked over (often found in the bases of Room heaters), or by thermal cut-out
switches /Thermostat . In addition to the these Safety devices ,Room Heater having non metallic
enclosure are equipped with thermal fuse also
.
The values of parameter to be declared by manufacturer :
I)Type : convection heater/fan heater/heater for use in green houses/Liquid filled radiators/panel
heater/Radiant heaters/tubular heaters.
Rating : Rated voltage in volts, Nature of Supply Voltage , Rated Frequency/Rated power input.
II)Classification : Class I/II/III .& Degree of protection against harmful ingress of water.
III) pollution Degree
IV) Material group if Pollution degree is other than 1.
.
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
ISSUE: 01
DATE: NOV 2013
PREPARED BY:
PRODUCT MANUAL
PAGE: 2 OF 4
APPROVED BY:
1.2. Latest Indian Standard Number with product title and number of amendments
Indian Standard Number: IS 302-2-30:2007
Product title: Safety of Household And Similar Electrical Appliances –Room Heater
No. of amendments: 1
1.3 List of referred standards
The following IS Standards are necessary adjuncts to this standard:
IS No.
Title
302-1:2008
SAFETY OF HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCRES
PART-1 GENERAL REQUIREMENTS.
1060 (part1):1966
revised)
1401:2007
Method of sampling and test for paper and allied products: part1(
Protection of persons & equipment by probes for verification(second revision)
11000(part2)/Sec2:1984 : Fire Hazards Testing :Part2 Test methods Sec.2 Needle flame Test
12766 :1997
paper ,computer- Specification ( Ist Revision)
OTHER RELEVANT STANDARDS
9968(Part-1)1988
Elastomer insulated cables:part-1 for working voltages up to & including
1100V ( 1st revision)
694 :1988
PVC insulated Cables for working voltage up to & including 1100 v ( 3rd
revision)
1293:2005
Plug& socket rated voltage & current up to & including 250V & 16A. (Third
revisionThe following IS Standards are necessary adjuncts to this standard:
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
PREPARED BY:
ISSUE: 01
DATE: NOV 2013
PRODUCT MANUAL
PAGE: 3 OF 4
APPROVED BY:
1.4. Check-list for submission of an application for grant of licence: As per Annexure 1
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
ISSUE: 01
PREPARED BY:
DATE: NOV 2013
PRODUCT MANUAL
PAGE: 2 OF 2
APPROVED BY:
SECTION 2: RAW MATERIALS/ COMPONENTS
2.1. List of important components
List of Major Component of Room Heater ( Fan Heater / Radiant Heater)
Sr. Name of Component
No
Check List
1
Visual Exam
No loose bobbin ,Al Bracket
fitting ,sign of rust
DoM
Measurement
Weight
Cross sectional area of wire
harness
Fan Motor
HVT/Flash ,LVS & Functional
Test
1500 V/5Sec
2
Thermostat / Self
Resettable Thermal
Cut Out
LVS
RPM on no load /On Load
Cold Resistance of Coil
Input on no load/ load
Visual Exam
Color of Zn plating,Rating &
marking,
Requirements
As per Ref Sample & DoM in
mmyy format
As per the wt model Ref. Sample
No flash over/breakdown shall
occur
120 V Max.
As per Ref Sample
As per Ref Sample
As per Ref Sample
Color of Chasis & Rating shall
match with that of Ref .
Sample& Marking in MMYY
format be Checked
Measurement
Dimensional Check of Shaft &
Chasis
put the thermostat in condition of
assembly & ensure.
As per Ref Sample
HVT/Flash Test
1500 V/5Sec
3
Switch
Visual Exam
Color , Moulding Defect, Rating
& printing
No flash over/breakdown shall
occur
as per Ref. sample.
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
ISSUE: 01
PREPARED BY:
4
Heating Element
DATE: NOV 2013
Main Suppy Cord with
moulded plug
PAGE: 2 OF 2
APPROVED BY:
Visual Exam
Ensure proper assembly &
loose Terminals
Measurement
Cold Resistance
5
PRODUCT MANUAL
As per Ref Sample
51 Ω - 55ΩΩ for IKW & 26 Ω - 28Ω
for 1Kw
Visual Exam
Colour ( PVC Cable) ,cotton
Braiding defects in
rubber cable Marking & Rating
of Plug & PVC Cable
As per Ref Sample
Measurement
Length of Cord & area of X-sec
of Copper
Conductor
As per Ref Sample.
HVT / Flash Over & continuity
Test
1500 V/5 Sec
Continuity
( Plug Pin L-with Red Core , BBlack Core
& E- Green/Yellow Core )
6
Reflector
Visual Exam
Electroplating Defect, Scratches ,
dents & burrs
Measurement
Weight
7
Metallic or Non metallic Enclosure
Shall with Stand
Shall Comply
As per Ref Sample
Visual Exam
Scratches ,Powder coating
/Screen Printing
dents/sharp edges , Deep Spot
welding marks
Colour Variation, Moulding
As per ref Sample
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
ISSUE: 01
PREPARED BY:
DATE: NOV 2013
PRODUCT MANUAL
PAGE: 2 OF 2
APPROVED BY:
Defects,
Measurement
Weight
As per ref Sample
IS Standards exist for the following component/ Raw Material
1. Main supply cord : IS 9968part-1(1988) & IS:694:1988
2. Three pin top
: IS:1293:2005
SECTION 3: MANUFACTURING PROCESS AND IN-PROCESS QUALITY
CONTROLS
3.1. Description of manufacturing process MANUFACTURING PROCESS AND IN-PROCESS
QUALITY CONTROLS
i)Description of manufacturing Process(es) with quality Checks MANUFACTURING PROCESS
& IN PROCESS CONTROLS ( FAN HEATER)
Stage
No
Stage
Check points
1
Bottom Assembly
No Color deviation,scratches,moulding defect,powder
coating defect ,loose connectioning of supply cords &
loose assembly of componenets i.e heating element,
motor, fan line connector switch ,thermostat.
2
Top Cover assembly
No Color Deviation,scratches,moulding defect,powder
coating defect ,loose connection & loose assembly of
component assembled ,effectiveness of screen printing.
3
Stage No (1+ 2)
No Visual Defects ,loose fitting misalignment missing of
component.
4
Visual Inspection
No moulding ,Printing , Visual Defects & Loose Fitment.
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
ISSUE: 01
PREPARED BY:
DATE: NOV 2013
PRODUCT MANUAL
PAGE: 2 OF 2
APPROVED BY:
5
Fixing of Rating Label & inspecting tag
No gap/Bending & Printing/Marking be legible& durable
6
Safety & Functional Test
7
Cleaning
H.V test-1.5kV/5sec, LC=210Um max,ECR-0.1Ohm
max,IR-10MOhm Min & Motor LVS, Element Glow &
functional test.
No Visual Defect /Missing. Cleaned Properly.
8
Packing Unit carton
9
Packaging Master Carton
10
Storage/Dispatch
Print Colour, Pasting/Stappling ,CM/L No.,Ensure GCard, Manual , Polybag & Pulp /Thermocol packing &
Correct Marking of MRP&Date of Manufacture
Print Colour,Pasting/Stappling /rust on stapples, CM/L
No,Consolidated MRP& Date of Manufacture
Nos of unit/Master & Taping & Strapping.
Storage Area – Cleaned,moisture proof,Stacking on
pallets
MANUFACTURING PROCESS & IN PROCESS CONTROLS ( RADIANT HEATER)
Stage
No
Stage
Check points
1
Main Assembly
4
Visual Inspection
5
Fixing of Rating Label & inspecting tag
No Color deviation,scratches,moulding
defect,powder coating defect ,loose
connectioning of supply cords & loose
assembly of componenets i.e heating
element, line connector, switch ,
Loosefitting ,misalignment of component.
No moulding ,Printing , Visual Defects,
Scratches , dents , deep lines & Loose
Fitment.
No gap/Bending & Printing/Marking be
legible& durable
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
ISSUE: 01
PREPARED BY:
DATE: NOV 2013
PRODUCT MANUAL
PAGE: 2 OF 2
APPROVED BY:
6
Safety & Functional Test
7
Cleaning
8
Packing Unit Carton
9
Packing Master Carton
10
Storage /Dispatch
14
Storage /Dispatch
H.V test-1.5kV/5sec, LC=210Um max,ECR0.1Ohm max,IR-10MOhm Min &
functional test.
No Visual Defect /Missing. Cleaned
Properly.
Print colour , Pasting/Stappling ,CM/L No,
MRP 'Ensure G-Card, Manual , Polybag &
Pulp /Thermocol packing & Correct
Marking of MRP&Date of manufacture
Print Colour of Sheet,
Pasting/Stappling,Consolidated MRP &
Date of Manufacture & Tape & Strapping
Storage area -clean,moisture proof,with
pallets & proper stacking
Storage area shall be clean , moisture proof & Proper Stacking on
Pallets
3.2. Infrastructure for production
Following basic manufacturing facilities shall be available at applicant unit for the production
ii) Infrastructure for production
Sl.
No.
1
2
3
4
5
6
7
8
List of Machinery
Electric/Pnuematic Screw Driver
along with Bits& nut runners of
different Sizes
Sr No Punching Machine/Laser
printing machine
Digital Weighing Machine
Hand Press
Hand Drill/Threading Machine
Conventional Hand Tools (
NosePliers, Thimble Crimping
Tools,Mallets,Hammers,Scissors,)
Pad Printing Machine
Motorised Conveyor System
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
ISSUE: 01
PREPARED BY:
9
10
11
DATE: NOV 2013
PRODUCT MANUAL
PAGE: 2 OF 2
APPROVED BY:
Electric Generator Set
Compressor
Electric Strapping Machine
The capacity and number of manufacturing
machines or testing machines may vary as per
production needs and applicability. The process
quality controls shall be followed as per STI for the product.
12
Tape Dispanser
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
ISSUE: 01
PREPARED BY:
DATE: NOV 2013
PRODUCT MANUAL
PAGE: 1 OF 2
APPROVED BY:
SECTION 4: CERTIFICATION CRITERIA
4.1. Identification of critical requirements
All requirements documented in standard shall be considered critical unless mentioned
otherwise.
4.2. Scheme of testing and inspection
The STI for IS 302-2-30:2007 as in force shall be applicable i.e. Doc: STI /302-2-30/2
September2009. The implementation of STI shall be verified during surveillance inspection.
4.3. Marking fee rates
The details of rate of marking fee are available on BIS intranet/website.
4.4. Grouping guidelines
No grouping guidelines are available for IS 302-2-30:2007
4.5. Guidelines for scope of licence
Licence shall be granted with scope specifying the type(s) of the product. Licence shall not be
granted with “open scope”. The grant of licence letter and the Licence Document shall clearly
indicate the following:
Safety of household and similar appliances – Electric Room heater (Fan Heater), 2000W,
230V, 50 Hz, ac, Class I, single phase, ordinary, IPXO, Pollution Degree 3, Material group III-a,
portable type, Insulation Class ‘E’ of fan motor winding, fitted with thermostat and self
resetting thermal cutout as per IS 302-2-30:2007.
4.6. Guidelines for inclusion of new varieties
Inclusion of other varieties shall e considered for the type of product for which confirming test
report as per guidelines submitted .
4.7. Sample size and Guidelines for drawl of separate samples
Sample sizes - 2
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
ISSUE: 01
PREPARED BY:
DATE: NOV 2013
PRODUCT MANUAL
PAGE: 6 OF 7
APPROVED BY:
4.8. Manner of sealing of sample(s)
Effort shall be made, as far as possible, to send samples without the manufacturer’s
identification and/or markings. Any label and/or manufacturer's identification shall be
removed or defaced.
Test request shall clearly indicate the following:
a) Date of manufacture;
b) Quantity,
c) Lot No.
4.9. Dealing with sample remnants
The remnants of samples may be disposed off after testing.
4.10. Procedure for destruction of non conforming product
The non conforming product shall be disposed off .
SECTION 5: INSPECTION AND TESTING
5.1. Packaging material requirement :
CorrugatedUnit/Master Carton , Thermocol/Pulp packing/Foam Sheet/Front
Impact Strip /Poly/Bubble bag/Manual&Guarantee card/Bopp
Tape/Straps/Sealing Wax.
5.2. List of test equipment/ facilities and Chaemicals
To be provided by CL
5.3. Test facilities in BIS Labs/ OSLs with testing charges and approximate time
The list of BIS laboratories and laboratories recognized by BIS, where sample of Electric
Iron can be sent for independent testing, are available on BIS intranet/website. The
inspecting officer/agent shall collect latest status in respect of any laboratory before
proceeding for inspection.
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
ISSUE: 01
PREPARED BY:
PRODUCT MANUAL
DATE: NOV 2013
PAGE: 6 OF 7
APPROVED BY:
5.4. Basis of grant of licence
The basis of grant of licence shall be based on independent testing.
5.5. Details of tests to be carried out in the factory
Following tests may be carried out in factory:
S.No
Tests
1
Protection against electric shock
2.
Electrical Insulation&Leakage current at
Ref to Cl.
8 of IS:302-2-30:2007
Operating Temperature
13
3.
Earthing connection
27
4.
Input
10
5.
Temperature Rise
11
6.
Stability & Mechanical Hazards
20
7.
Mechanical Strength
21
8.
Screw & connection
28
9.
Resistance to heat & fire
30
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
ISSUE: 01
PRODUCT MANUAL
DATE: NOV 2013
PREPARED BY:
PAGE: 1 OF 1
APPROVED BY:
ANNEX-I
CHECK-LIST FOR APPLICATION TO BE SUBMITTED BY APPLICANT TO BIS
WHILE APPLYING FOR BIS LICENCE UNDER PRODUCT CERTIFICATION SCHEME OF BIS
The following check-list is required to be submitted with all the applications for grant of BIS licence under
the Product Certification Scheme of BIS. Please tick (√) in the relevant box.
Whether applied under: Simplified Procedure
□
Normal Procedure
□
Note: Refer BIS website or details of “Simplified Procedure” and “Normal Procedure” for grant of licence.
No.
Check-point
General
1.
Name &
Address
2.
Status of
Applicant
(Manufacturi
ng
Unit)
3
IS No. &
Varieties
4.
History
5.
Signature
6.
Machinery
Requirement
Is the application form completely filled?
Is the name and address of applicant (manufacturing
unit applying for licence) same in the application as
given in the attached document of Central/State
Government
a. Has it been indicated whether the applicant is a
large scale or small scale unit?
b. In case the applicant is a small scale unit, does the
applicant hold valid Registration Certificate from
the Local / State authority or from a Chartered
Accountant, and is the certificate attached.
c. Has it been indicated whether the applicant is a
Public Sector or a Private Sector company?
a. Has applicant recorded the applicable Indian
Standard with correct title of the Standard?
b. Where applicable, has applicant mentioned
designation, grade, type, variety, size, etc., of the
product for which the BIS licence is sought?
a. Where applicable, has the applicant provided
information regarding earlier BIS licence(s) held by
them and / or cancelled in the past?
b. Where applicable, has the applicant provided
information regarding BIS licences currently held
by them?
a. Is the application signed by the CEO of the
applicant?
b. In case the application is signed by a person other
than the CEO, is the application signed by the
authorized signatory of the applicant and his
authorization is attached by the authorized
signatory?
a. Does applicant possess requisite manufacturing
infrastructure to manufacture the product as per the
Indian Standard?
b. Is installed capacity of production indicated in the
application?
Observations
Page No.
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
PREPARED BY:
7.
Test
Equipment
&
Calibration
8.
QC personnel
9.
Raw
Materials
and
Components
10.
Plant Layout
11.
Test
Report(s)
ISSUE: 01
DATE: NOV 2013
APPROVED BY:
c. Does applicant have all machineries installed as
per manufacturing process at the applicant’s
manufacturing premises?
d. If answer to ‘c’ above is no, does the applicant
outsource any of its manufacturing processes and
possesses
valid
agreement(s)
with
other
manufacturing units for the outsourced processes
and traceability of material, thus produced, etc.?
e. If answer to ‘d’ above is yes, does the applicant
has any control over such outsourced activity? Are
these outsourced process will ensure testing the
quality of final product for all requirements at the
applicant's manufacturing premises?
a. Does applicant possesses requisite test facilities
in-house as per the relevant Indian Standard at its
factory address?
b. Are valid calibration certificates for relevant test
equipment attached are complete and valid at least 3
months after the date of recording?
c. If reply to ‘a’ above is no, does applicant have
arrangement with a BIS recognized outside lab for
testing of the requirements for which it does not
possess test facilities inhouse? Is the consent letter
as attached by applicant in this regard in order?
Note: Relaxation in in-house test facilities may be
allowed on submission of proper justification for
requirements which are obligatory to get tested and
for which frequency of testing, as prescribed in the
relevant scheme of testing and inspection (STI),
is, normally, one month or more.
Does the applicant employ qualified & experienced
Quality Control (QC) personnel on permanent basis
and possess documentary evidence to establish the
same? Are the copies of the qualification certificates
and appointment letters of the QC personnel are in
order.
Where ever requirements for raw materials/
components used in the manufacturing of the
product are specified in the standard, do test
reports/suppliers’ test certificates, as submitted by
the applicant show that these requirements are met
as per the standard?
Does copy of the plant (applicant manufacturing
premises) layout clearly indicates locations of
manufacturing machinery, laboratory, office,
workshop, amenities, storage area, etc.?
a. Is the attached test report of in-house or from
independent laboratory cover all requirements of the
Indian Standard and ispassing in such requirements?
PRODUCT MANUAL
PAGE: 1 OF 1
BUREAU OF INDIAN STANDARDS
PRODUCT CERTIFICATION
TITLE: GENERAL
DOC: PC-302-2-30-
2007
PREPARED BY:
12.
Undertaking
ISSUE: 01
DATE: NOV 2013
APPROVED BY:
b. In case the application is filed under “simplified
Procedure” is the test report(s), in original, as
submitted a) from BIS or its recognized
laboratories? b) the test report is not older than
one month from the date of submission of
application, c) covers all the requirements of the
standard, and d) passes in all such requirements
In case application is under simplified procedure, an
undertaking shall be obtained from the applicant on
his letter-head that the licence if granted against his
application shall be put under Stop Marking by BIS
if the verification sample(s) (any sample including
the long duration test samples) drawn during visit of
the BIS officer prior to grant of licence fail to
conform to the requirements of relevant Indian
Standards. The licensee shall take necessary
corrective actions and inform the same to BIS along
with fresh samples (of rating/size/variety which
facilitates verification of corrective actions on the
reported failures) manufactured after taking the
corrective actions. The resumption of marking in
such cases shall be allowed only on the basis of
independent satisfactory Test Reports of the fresh
samples offered (including long duration tests where
failures were in long duration tests). In case the
fresh sample drawn by BIS for independent testing
fails, or the licensee does not inform corrective
actions taken and does not offer improved samples
within 1 month of the date of Stop Marking, the
licence shall be processed for cancellation and no
further chance would be given to the licensee
PRODUCT MANUAL
PAGE: 1 OF 1