2,000 kWe Combined Heat and Power System - Dresser-Rand

CHP 2000
2,000 kWe Combined Heat and Power System
Dresser-Rand pro­vides a
complete range of fully
packaged and tested combined
heat and power (CHP) systems
to commercial, industrial and
municipal energy users world­
wide. CHP (or cogeneration)
systems reduce on-site energy
costs and carbon dioxide
emis­sions through the highly
effi­cient delivery of power and
heating.
KG2-3G high-efficiency gas turbine
Cogeneration or combined heat and power (CHP) systems facilitate the production
of electricity and useful heat at very high efficiency. By locating a power generation
system at the heart of your facility or process it is possble to capture the heat which
is usually a wasted by-product of electricity generation.
The KG2 cogeneration system combines the reliable Dresser-Rand® KG2-3G gas
turbine with a pre-engineered steam heat recovery package. The system provides
a continuous base load supply of both electricity and steam while lowering energy
costs and CO2 emissions. With a range of steam pressure configurations available,
this system can be matched to almost any process need.
CHP 2000 System Output
Metric
Imperial
Electric output
1,950 kWe
2,614.993 hp
Electric generator frequency
50 / 60 Hz
50 / 60 Hz
Steam output at 10 bar / 145 PSI
5.8 t/h
12.7868 lbs/hr
Chilling at 37 / 30 °C, 98.6 / 86 °F
5.50 MW
7375.621 hp
Hot water from 10 to 80 °C, 50 to 176 °F
16 kg/sec
35.27392 lbs/sec
Metric
Imperial
Turbine shaft speed
25,500 rpm
25,500 rpm
Output shaft speed
1,500 or 1,800 rpm
1,500 or 1,800 rpm
CHP output choices:
Turbine Model KG2-3G
Combustor type
Emission NOx/CO (@15% O2)
Pressure ratio
Exhaust gas mass flow
Exhaust gas temperature
Combustor cans
25 / 10 ppm
25 / 10 ppm
7
7
9.50 kg/sec
21.01 lb/sec
577 °C
1,071 °F
Fuel type
Natural gas
Natural gas
Fuel rate
14,182 kJ/kWh
13,442.27 BTU/kWh
For more information about
Dresser-Rand's CHP 2000, please contact us at one of the following locations:
Dresser-Rand AS
Kirkegardsveien 45
P.O. Box 1010
NO-3601 Kongsberg, Norway
Tel: (Int'l +47) 322 87070
Fax: (Int'l +47) 322-87080
Dresser-Rand
1202 W. Sam Houston Pkwy. N.
Houston, TX 77043 USA
Tel: (Int'l +1) 713-365-2630
Fax: (Int'l +1) 713-365-2660
For a complete list of products and
services, visit www.dresser-rand.com
or contact us at the following locations:
Dresser-Rand
Corporate Headquarters
West8 Tower Suite 1000
10205 Westheimer Road
Houston, TX 77042 USA
Tel: (Int'l +1) 713-354-6100
Fax: (Int'l +1) 713-354-6110
112, Avenue Kleber
75784 – Paris Cedex 16
Tel: (Int’l +33) 156 26 71 71
Fax: (Int’l +33) 156 26 71 72
email: info@dresser-rand.com
Regional Headquarters
The Americas
Dresser-Rand
West8 Tower Suite 1000
10205 Westheimer Road
Houston, TX 77042 USA
Tel: (Int'l +1) 713-354-6100
Fax: (Int'l +1) 713-354-6110
EMEA
(Europe, Middle East, Africa)
Dresser-Rand S.A.
31 Boulevard Winston Churchill
Cedex 7013
Le Havre 76080 France
Tel: (Int'l +33) 2-35-25-5225
Fax: (Int'l +33) 2-35-25-5366 / 5367
Asia Pacific
Dresser-Rand Asia Pacific Sdn Bhd
Unit 9-4, 9th Floor
Bangunan Malaysian Re
17 Lorong Dungun
Damansara Heights
50490 Kuala Lumpur, Malaysia
Tel: (Int'l +60) 3-2093-6633
Fax: (Int'l +60) 3-2093-2622
CHP Sizing and Selection
Packaged CHP systems deliver the maximum possible energy cost savings when
deployed in applications where the electrical and thermal outputs of the system
can be consumed at all times by the host facility.The standard CHP 2000 system
delivers high-quality steam (approximately 5.8 t/h at 10 bar (12.7 lb/h at 145 PSI)
when operated at base load). Alternatively, the exhaust energy can be used for
chilling and delivers approximately 5.5 MW of chilling power. A balance of both
is also possible, and in addition can be hot water extracted from the lubricant oil
cooler. A steam condenser is required to boost the total efficiency to somewhere
in the mid-90% range. Dresser-Rand has experienced engineers available to
discuss your precise CHP requirements and to help ensure that you select the most
appropriate system for your building or process. Dresser-Rand CHP systems can
be designed to meet application-specific requirements.
CHP Package Data
CHP Dimension Data
LTHW flow temperature: 180 °F / 82.2 °C
Length: 40ft / 12.192 meters
LTHW return temperature: 160 °F / 71.1 °C
Height: 8ft / 2.438 meters
Noise dB(A) at 25' <75
Height: 8ft 6in / 2.591 meters
GPM of hot water (20 °F delta T): 520
Weight: 38,000lbs / 17.2 tons
2,000 kWe of Continuous, On-site Electrical Power
Energy consumers demand high efficiency and reliability in order to minimize
operating costs and maximize uptime. Our CHP systems are supplied as as
comprehensive factory tested package that can be easily integrated into existing
site operations. Items such as synchronizing switchgear, heat recovery equipment,
emissions treatment, attenuation, and lube oil systems are included "within the
box." This dramatically reduces the risk of cost overruns and performance issues
associated with traditional "site built" systems.
Features
Benefits
Single-shaft gas turbine with cold end
bearings
Near zero lubrication oil consumption with
long-life bearings
Custom acoustic enclosure system
Provides optimal noise attenuation and
easy access for maintenance
Integrated programmable logic controller
(PLC) and remote monitoring system
Allows for remote and on-site monitoring
and reporting as well as communication
to the site's existing building management
system
Simple, durable design
Allows for long intervals between major
overhauls and only one annual visual
inspection
Full load factory test (optional)
Ensures full capabilities before leaving the
factory
DLE combustors
Lower emissions with high fuel flexibility
and widely accepted fuel range
High power density turbine
Small and lightweight 2MW gas turbine
for a non-permit load packager; easy to
maintain and ship
©2013 Dresser-Rand. This document comprises a general overview of the products described herein. It is solely for informational purposes, does not represent a warranty or guarantee of the information contained herein and is not to be construed as an offer to sell or
a solicitation to buy. Contact Dresser-Rand for detailed design and engineering information suitable to your specific applications. DresserRand reserves the right to modify its products and related product information at any time without prior notice.
Form 2294