Xplova E5 Cycling Computer Guide Classroom

Xplova E5 Cycling Computer Guide Classroom
Lesson II Sensor-pairing
In lesson I, you can learn the E5 basic settings.
This one will be introduced how to pair with combo sensor , heart rate monitor,
power meter and calibrating the power meter.
You can also download the English user manual from following webpage,
http://download.xplova.com/E5/E5UM/Xplova_E5_UM_EN.pdf
If you just want to manually set up E5 cycling computer, you can refer to the
English user manual from page 30 to page 35
HRM ( heart rate monitor)
-------------------------------------------------------------------------------------------------The HRM menu allows you to monitor your exercise and body condition.
The Heart Rate Monitor (HRM) is attached to an elastic band worn around the
chest. This section describes how to pair and wear the heart rate monitor
.
How to wear and pairing the Heart Rate Monitor?
Pairing connects the Heart Rate Monitor to your Xplova E5, allowing
heart rate to be recorded and displayed on screen
Press long = Press the button for 2 seconds and then release the button
A popup on the Xplova E5 indicates when the HRM is paired.
While E5 successfully paired successfully with a heart rate monitor (HRM),
below the HRM SCAN successful will display numeric on Lower Screen of E5
The significance of the numeric is the ID of HRM.
(Note: all HRM ID are different)
After HRM complete to pair with E5, you have to short press the button
“LAP/RESET” twice. Confirm to save the pairing information and return
to the previous screen.
If you want to know more clearly, you can refer to the following pairing videos.
http://www.youtube.com/watch?v=BW
Wearing the Heart Rate Monitor
After pairing, wear the heart rate monitor around your chest as close as
possible to the heart with the monitor segment worn in the middle of the chest
1. Unbuckle the strap.
2.
Wrap the strap around your chest and re-buckle it.
3.
Adjust the circumference of the band to fit.
Combo Cadence Sensor
--------------------------------------------------------------------------------------------------The combo cadence (includes the cadence sensor and a speed sensor)
attaches to the chain stay of your bike to help you track your speed and
cadence accurately
Pairing
the Combo Cadence Sensor
While E5 successfully paired successfully with a Combo Cadence Sensor,
below the CMB SCAN successful will display numeric on Lower Screen of E5.
The significance of the numeric is the ID of CMB.
(Note: all CMB ID are different)
After Combo Cadence sensor complete to pair with E5, you have to short
press the button “LAP/RESET” twice. Confirm to save the pairing
information and return to the previous screen.
If you want to know more clearly, you can refer to the following pairing videos.
http://www.youtube.com/watch?v=BW
How to install combo cadence sensor? you can refer to the following image.
Or Follow the demonstration,
After pairing the combo cadence sensor, install the sensor on your bike.
1) Position the sensor on the chain stay of your bike
2) Use the supplied cable ties to hold the sensor in place. Do not fully tighten.
3) Attach the magnet to a spoke. Do not fully tighten
4) Attach the magnet to the left crank. Do not fully tighten
5) Adjust the magnets and the sensors, making sure the air gap between
sensor markings and magnets is less than 5 mm
6) When setup is complete, tighten the cable ties
Every bicycle frame size is not the same.When you want to assemble
combo sensor to the frame, you abide by assembling principle
(Assembly principle is the same).Therefore, some users speed sensor
assembly will skew, or cadence sensor assembly will skew.
As long as it can be pairing, the skew assembled position is also
possible. Please refer to the actual most suitable for you assemble
pictures.
speed sensor assembly will skew
Or go to visit
http://blog.udn.com/serafinamor/6788764
Power Meter
------------------------------------------------------------------------------------------------------The following power meter devices are compatible to your Xplova E5:
SRM, Quarq, Power2Max and Power Tap.
NOTE: For the most updated compatible ANT+ power meter information, visit
www.xplova.com
Pairing with the Power Meter
While E5 successfully paired successfully with a Power Meter,
below the PWR SCAN successful will display numeric on Lower Screen of E5.
The significance of the numeric is the ID of PWR.
(Note: all PWR ID are different)
After Power Meter complete to pair with E5, you have to short press the
button “LAP/RESET” twice. Confirm to save the pairing information and
return to the previous screen.
If you want to know more clearly, you can refer to the following pairing videos.
http://www.youtube.com/watch?v=BW
Calibrating the Power Meter
While starting to calibrate, you should follow the principle of factory calibration
and make sure not to rotate the wheel
While power meter calibrated successfully with E5,
below the PWR CALI successful will display numeric on Lower Screen of E5.
The significance of the numeric is the ID of PWR CALI.
(Note: all PWR CALI ID are different)
After Power Meter complete to calibrate with E5, you have to short press the
button “LAP/RESET” three times. Confirm to save the calibrating
information and return to the previous screen.
If you want to know more clearly, you can refer to the following pairing videos.
http://www.youtube.com/watch?v=BW
After you learn lesson I & lesson II, you can ride now & use Xplova E5 to
record your activities. Let’s Go!