docLegacy Series - CIRCOR Energy
download 
Report Transcription
Legacy Series - CIRCOR Energy
Legacy Series Series 1-4 Ball & Seat Threaded Safety Relief Valves General Design Features • Incorporates Hydroseal’s “Self-Seeking Soft Seat” Design • Ideal Where Economical Low Flow Overpressure Protection is Required • • • • ASME Section VIII UV Code Stamped for Air & Gas Available for Non-Code Liquid Applications Operating Temperatures to 800°F 1/4"-1" NPT Inlet Sizes Dimension Data Cap Type Closed Cap Lever Cap C A B Part Number Codes Inlet x Ou tl rifice et / O erial Mat Cap Type ing / O -R Seat Soft Specify Model Number (Lower Right) 0 • Std. Trim 2 • Std. Trim w/Stellite® Ball 3 • All 316SS w/Stellite® Ball 4 • All 316SS w/Inconel® Spring & Stellite® Ball (NACE) 5 • 316SS Trim w/Stellite® Ball 6 • 316SS Trim w/Inconel® Spring & Stellite® Ball (NACE) 7 • Std. Material w/Inconel® Spring 0 • Closed Cap L • Open Lift Lever P • Packed Lift Lever ASME Code requires lift lever on air service. 0 • Nitrile (Buna-N) O-Ring w/Viton® Soft Seat C • Neoprene E • EPDM F • Fluorocarbon (Viton® ) K • Kalrez® O-Ring w/Viton® Soft Seat M • Metal Gasket N • Nitrile (Buna-N) Elastomer selection is media and temperature dependent. Spring Code Consult Factory for Spring Chart. 14EV 0 0 F/ XX Example 2 Hydroseal Legacy Series A 3.00 3.00 Dimension (in.) B 1.75 1.75 C 9.00 10.00 Weight (lbs.) 5 6 Sizing Information Orifice Area AV/DV BV/EV CRV/FRV CXV/FXV 0.049 0.110 0.196 0.248 Gas KD — 0.34 0.31 0.25 Liquid KD 0.11 0.07 0.13 0.15 Slope — 0.68 1.11 1.15 Liq. Flow Factor 0.20 0.30 0.95 1.40 Leak tested in accordance with factory standard. Contact Factory in order to receive sizing program and/or capacity charts. Water capacities determined at 25% over set pressure. Model Number Model 14AV 14BV 14DV 14EV 38AV 38BV 38DV 38EV 2AV 2BV 2CXV* 2CRV*+ 2DV 2EV 2FXV* 2FRV*+ Inlet x Outlet Orifice Max Set FNPT x FNPT Dia. (psig) 1/4 4350 1/4 x 3/4 3/8 1350 1/4 4350 1/4 x 1 3/8 1350 1/4 3800 3/8 x 3/4 3/8 3800 1/4 3800 3/8 x 1 3/8 3800 1/4 4850 3/8 4850 1/2 x 3/4 9/16 3500 1/2 2500 1/4 4850 3/8 4850 1/2 x 1 9/16 3500 1/2 2500 Models 14, 38 and 1/4" orifice are not ASME Code Stamped valves. * Non-Code Below 21 psi + Soft Seat Valve Model 1AV 1BV 1CXV* 1CRV*+ 1DV 1EV 1FXV* 1FRV*+ 3AV 3BV 3CXV* 3CRV*+ 3DV 3EV 3FXV* 3FRV*+ 4DV 4EV 4FXV* 4FRV*+ Inlet x Outlet Orifice Max Set MNPT x FNPT Dia. (psig) 1/4 10,800 3/8 6000 1/2 x 3/4 9/16 2600 1/2 2500 1/4 10,800 3/8 6000 1/2 x 1 9/16 2600 1/2 2500 1/4 12,500 3/8 6000 3/4 x 3/4 9/16 3500 1/2 2500 1/4 12,500 3/8 6000 3/4 x 1 9/16 3500 1/2 2500 1/4 12,500 3/8 6000 1x 1 9/16 3500 1/2 2500 Series 1-4, Parts List & Material Selection Index Description 1 2 3 4 5 6 7 8 9 10 11 12 Valve Cap Adjusting Screw Adjusting Lock Nut Cap Seal Body Guide Stem Upper Spring Plate Spring Lower Spring Plate Ball Seat Body/Seat Seal Open Lift Lever Cap Release Nut Release Washer Lever Pin Lever Packed Lift Lever Cap Release Nut Release Washer Lock Nut Gland Nut Gland O-Ring Lever Shaft Lever Pin Shaft O-Ring Lever 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 0 CS CS SS 2 CS CS SS WCB WCB SS SS SS SS SS SS SS SS 440C SS Stellite® SS SS Material Code 4 5 6 7 316SS CS CS CS 316SS 316SS 316SS CS 316SS 316SS 316SS SS Specify CF8M CF8M WCB WCB WCB 316SS 316SS 316SS 316SS SS 316SS 316SS 316SS 316SS SS 316SS Inconel® 316SS Inconel® Inconel® 316SS 316SS 316SS 316SS SS Stellite® Stellite® Stellite® Stellite® 440C SS 316SS 316SS 316SS 316SS SS Specify 3 316SS 316SS 316SS WCB CS CS SS CS WCB CS CS SS CS CF8M 316SS 316SS 316SS 316SS CF8M 316SS 316SS 316SS 316SS WCB CS CS SS CS WCB CS CS SS CS WCB CS CS SS CS CS SS SS CS SS CS SS SS CS SS 316SS 316SS 316SS 316SS 316SS CS SS SS CS SS CS SS SS CS SS CS SS SS CS SS SS CS SS CS SS SS SS CS SS CS SS CS CS CS 316SS 316SS 316SS 316SS 316SS 316SS Specify SS SS Specify 316SS CS CS CS Materials: CS-Carbon Steel, SS-Stainless Steel, WCB -ASME SA 216, CF8M -ASME SA 351 Hydroseal Legacy Series 3 Series 5-8 Ball & Seat Threaded Safety Relief Valves General Design Features • Soft Seat Option Provides Primary Seal with a Metal-To-MetalSecondarySeal • ASME Section VIII UV Code Stamped for Air & Gas • Available for Non-Code Liquid Applications • 1"- 2" Inlet Sizes • Incorporates Hydroseal’s “Self-Seeking Soft Seat” Design • Operating Temperatures to 600°F Dimension Data Cap Type Closed Cap Lever Cap C A B Part Number Codes Dimension (in.) B 3.00 3.00 A 3.88 3.88 C 13.13 15.50 Weight (lbs.) 20 22 Sizing Information Orifice Area ARV AXV BV CRV CV 0.196 0.248 0.441 0.785 0.785 Gas KD 0.31 0.25 0.40 0.22 0.22 Liquid KD 0.13 0.16 0.14 0.16 0.16 Slope 1.11 1.15 3.22 3.09 3.13 Liq. Flow Factor 1.0 1.5 2.4 4.9 4.9 Leak tested in accordance with factory standard. Contact Factory in order to receive sizing program and/or capacity charts. Water capacities determined at 25% over set pressure. Model Number Model 8ARV*‡ 8AXV + 8BV 8CV 8CRV*# 5ARV*‡ 5AXV + 5BV 5CV 5CRV*# Model 6ARV*‡ 6AXV + 6BV 6CV 6CRV*# 7ARV*‡ 7AXV + 7BV 7CV 7CRV*# Inlet x Outlet FNPT x FNPT 1x 2 1 1/4 x 2 Inlet x Outlet MNPT x FNPT 1 1/2 x 2 * Soft Seat Valve + ASME Certified to 3500 psi # Non-Code Below 18 psi ‡ Non-Code Below 21 psi 4 Hydroseal Legacy Series 2x 2 Orifice Diameter 1/2 9/16 3 /4 1 1 1/2 9/16 3 /4 1 1 Max Set (psi) 2000 6000 3000 2000 2000 2000 6000 3000 2000 2000 Orifice Diameter 1/2 9/16 3 /4 1 1 1/2 9/16 3 /4 1 1 Max Set (psi) 2000 6000 3000 2000 2000 2000 6000 3000 2000 2000 Series 5-8, Parts List & Material Selection 1 16 2 17 3 18 21 25 19 22 26 20 23 27 28 4 29 5 30 6 24 7 8 Open Lift Lever 9 Packed Lift Lever 10 11 Index Description 12 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Valve Cap Adjusting Screw Adjusting Lock Nut Cap Seal Bonnet Guide Stem Upper Spring Plate Spring Body Bonnet Seal Body Stem Lock Nut Lower Spring Plate Ball Seat Body/Seat Seal Open Lift Lever Cap Release Nut Lever Pin Release Washer Lever Packed Lift Lever Cap Release Nut Release Washer Lock Nut Gland Nut Gland O-Ring Lever Shaft Lever Pin Shaft O-Ring Lever 13 14 15 Soft Seat Option Model ARV/CRV Molded Viton® seal standard optional materials available. 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 0 CS CS SS 2 CS CS SS WCB SS SS SS WCB SS SS 316SS WCB WCB SS SS SS SS 440C SS Stellite® SS SS Material Code 4 5 6 7 316SS CS CS CS 316SS 316SS 316SS CS 316SS 316SS 316SS SS Specify CF8M CF8M WCB WCB WCB 316SS 316SS 316SS 316SS SS 316SS 316SS 316SS 316SS SS 316SS Inconel® 316SS Inconel® Inconel® Specify CF8M CF8M WCB WCB WCB 316SS 316SS 316SS 316SS SS 316SS 316SS 316SS 316SS SS Stellite® Stellite® Stellite® Stellite® 440C SS 316SS 316SS 316SS 316SS SS Specify 3 316SS 316SS 316SS WCB CS SS CS CS WCB CS SS CS CS CF8M 316SS 316SS 316SS 316SS CF8M 316SS 316SS 316SS 316SS WCB CS SS CS CS WCB CS SS CS CS WCB CS SS CS CS CS SS SS CS SS CS SS SS CS SS 316SS 316SS 316SS 316SS 316SS CS SS SS CS SS CS SS SS CS SS CS SS SS CS SS SS CS SS CS SS SS SS CS SS CS SS CS CS CS 316SS 316SS 316SS 316SS 316SS 316SS Specify SS SS Specify 316SS CS CS CS Materials: CS-Carbon Steel, SS-Stainless Steel, WCB -ASME SA 216, CF8M -ASME SA 351 Hydroseal Legacy Series 5 FT, HC (Air) & HD (Liquid) Series Threaded Safety Relief Valves General Design Features • Disc & O-Ring Soft Seat Design Provides High Flow • ASME Semi-Nozzle Fixed Blowdown Valve • Bubble Tight Seal Suitable for Various Relief Applications up to 80% of Set Pressure • Inlets from 3 /4"- 2" with Set Pressures to 3500 psi • ASME Section VIII UV Code Stamped C A B Dimension Data Model/ Cap Type Series FT Part Number Codes Series HC FT HC Closed Cap Lever Cap Closed Cap Lever Cap A 3.88 3.88 3.88 3.88 Dimension (in.) B 2.13 2.13 3.00 3.00 C 14.88 16.88 16.63 18.88 Weight (lbs.) 15 17 25 27 Sizing Information Orifice Area FT HC/HD 0.306 0.785 Gas KD 0.87 0.88 Liquid KD — 0.60 Slope 4.88 12.63 Liq. Flow Factor — 17.6 FT is Air/Gas service only. Contact Factory in order to receive sizing program and/or capacity charts. Model Number Model Inlet x Outlet Air Liquid MNPT x FNPT FNPT x FNPT 3/4 x 1 1/2 — — 3FT — 4FT — 1 x 1 1/2 — 5FT — 1 x 1 1/2 — 5HC 5HD 1 1/4 x 2 — 6HC 6HD 1 1/2 x 2 — 7HC 7HD 2x2 6 Hydroseal Legacy Series Orifice (sq. in.) 0.306 0.306 0.306 0.785 0.785 0.785 Max Set (psig) 3500 1000 3500 2000 2000 2000 FT, HC (Air) & HD (Liquid) Series, Parts List & Material Selection Index 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 Description 0 CSZ CSZ CSZ 1 CSZ CSZ CSZ Cap Adjusting Screw Adjusting Lock Nut Cap Seal Bonnet WCB WCB Upper Spring Plate SS SS Spring CS 316SS Guide Stem SS SS Stem Lock nut SS SS Lower Spring Plate SS SS Spindle Guide 17- 4PH 17- 4PH Bonnet Seal Spindle SS SS Body WCB WCB Disk Retainer Screw SS SS Disk Seal Disk SS SS O-Ring Seat O-Ring Retainer SS SS Seat SS SS Seat Seal Body Seal (FT only) Base (FT only) CS CS Ball (FT only) 440C 440C Open Lift Lever Lever Pin SS SS Cap WCB WCB Release Nut CS CS Release Washer CS CS Lever CS CS Packed Lift Lever Cap CS CS Release Nut SS SS Release Washer SS SS Lock Nut CS CS Gland Nut SS SS Gland O-Ring Lever Shaft SS SS Lever Pin CS CS Shaft O-Ring Lever CS CS Material Code 3 4 5 316SS 316SS CSZ 316SS 316SS 316SS 316SS 316SS 316SS Determined By Soft Seat Selection CF8M CF8M WCB 316SS 316SS 316SS 316SS Inconel® 316SS 316SS 316SS 316SS 316SS 316SS 316SS 316SS 316SS 316SS 316SS 316SS 316SS Determined By Soft Seat Selection 316SS 316SS 316SS CF8M CF8M WCB 316SS 316SS 316SS Determined By Soft Seat Selection 316SS 316SS 316SS Determined By Soft Seat Selection 316SS 316SS 316SS 316SS 316SS 316SS Determined By Soft Seat Selection Determined By Soft Seat Selection 316SS 316SS 316SS SS SS SS 6 CSZ 316SS 316SS 7 CSZ CSZ CSZ WCB WCB 316SS SS Inconel® Inconel® 316SS SS 316SS SS 316SS SS 316SS 17- 4PH 316SS WCB 316SS SS WCB SS 316SS SS 316SS 316SS SS SS 316SS SS CS 440C 316SS CF8M 316SS 316SS 316SS 316SS CF8M 316SS 316SS 316SS SS WCB CS CS CS SS WCB CS CS CS SS WCB CS CS CS 316SS 316SS 316SS 316SS 316SS 316SS 316SS 316SS 316SS 316SS Specify SS SS Specify 316SS CS SS SS CS SS CS SS SS CS SS CS SS SS CS SS SS CS SS CS SS CS CS CS CS SS SS 316SS Materials: CS-Carbon Steel, SS-Stainless Steel, WCB - ASME SA 216, CF8M - ASME SA 351, CSZ - Carbon Steel - Zinc Plated Hydroseal Legacy Series 7 HC (Air) & HD (Liquid) Series Flanged Safety Relief Valves General Design Features • Disc & O-Ring Soft Seat Design Provide High Flow • ASME Semi-Nozzle Fixed Blowdown Valve • Bubble Tight Seal Suitable for Various Relief Applications up to 80% of Set Pressure • ASME Section VIII UV Code Stamped Sizing Information Orifice Area HC/HD 0.785 A B Part Number Codes 8 Hydroseal Legacy Series Liquid KD 0.60 Slope 12.63 Liq. Flow Factor 17.6 Contact Factory in order to receive sizing program and/or capacity charts. Model Number & Dimension Data Model C Gas KD 0.88 20FL 22FL 21FL 23FL 24FL 25FL 28FL 29FL 26FL 30FL 36FL 37FL 38FL 44FL 47FL 31FL 33FL 39FL 40FL 42FL 45FL 32FL 34FL 35FL 41FL 43FL 46FL 50FL 51FL 52FL 53FL 54FL 60FL 61FL 62FL 63FL 64FL 65FL 66FL 67FL Inlet x Outlet 1 1/2 x 1 1/2 1 1/2 x 2 1 1/2 x 2 1/2 2 x2 2 x 2 1/2 2x3 2 1/2 x 2 1/2 2 1/2 x 3 3x3 3x4 Flange Inlet x Outlet 150 x150 300 x150 150 x150 300 x150 600 x 150 600 x 300 900 x150 900 x 300 600 x 150 150 x 150 600 x 150 600 x 300 600 x 600 1500 x300 900 x 150 150 x 150 300 x 150 600 x 150 600 x 300 1500 x300 1500 x 600 150 x 150 300 x 150 300x300 600 x 150 1500 x300 900 x 150 150 x150 150 x150 300 x 150 600 x 150 600 x 300 150 x150 300 x150 300x 300 600 x 150 600 x 300 150 x 150 300 x150 600 x150 A 6 3/4 6 3/4 6 3/4 6 3/4 6 3/4 6 3/4 6 3/4 6 3/4 6 3/4 6 7/8 6 7/8 6 7/8 6 7/8 8 1/8 8 1/8 6 7/8 6 7/8 6 7/8 6 7/8 8 1/8 8 1/8 6 7/8 6 7/8 8 1/8 6 7/8 8 1/8 8 1/8 8 8 8 8 8 8 8 8 8 8 8 8 8 Dimension (in.) B C 4 7/8 18 7/8 4 7/8 18 7/8 7 4 /8 18 7/8 7 4 /8 18 7/8 7 4 /8 18 7/8 7 4 /8 18 7/8 7 4 /8 18 7/8 7 4 /8 18 7/8 7 4 /8 18 7/8 1 6 /8 19 5/8 1 6 /8 19 5/8 1 6 /8 19 5/8 1 6 /8 19 5/8 1 7 /4 21 7 1/4 21 6 1/8 19 5/8 6 1/8 19 5/8 1 6 /8 19 5/8 1 6 /8 19 5/8 1 7 /4 21 7 1/4 21 6 1/8 19 5/8 6 1/8 19 5/8 1 7 /4 21 6 1/8 19 5/8 7 1/4 21 7 1/4 21 7 1/4 21 7 1/4 21 7 1/4 21 7 1/4 21 7 1/4 21 7 1/4 21 7 1/4 21 7 1/4 21 7 1/4 21 7 1/4 21 7 1/4 21 7 1/4 21 7 1/4 21 Weight (lbs.) 35 37 37 39 42 45 53 55 48 47 48 49 53 67 79 55 59 61 62 67 75 59 60 62 63 76 77 69 71 73 75 75 71 73 75 77 79 77 79 81 HC (Air) & HD (Liquid) Series, Parts List & Material Selection Index 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 1 2 3 4 5 6 + 7 + 8 Material Code 3 4 5 Cap 316SS 316SS CSZ Adjusting Screw 316SS 316SS 316SS Adjusting Lock Nut 316SS 316SS 316SS Cap Seal Determined by Soft Seat Selection Guide Stem SS SS 316SS 316SS 316SS Upper Spring Plate SS SS 316SS 316SS 316SS Bonnet WCB WCB CF8M CF8M WCB Spring CS 316 SS 316SS Inconel® 316 SS Stem Lock Nut SS SS 316SS 316SS 316SS Lower Spring Plate SS SS 316SS 316SS 316SS Disk Retainer Screw SS SS 316SS 316SS 316SS Disk Seal Determined by Soft Seat Selection Disk SS SS 316SS 316SS 316SS O-Ring Seat Determined by Soft Seat Selection O-Ring Retainer SS SS 316SS 316SS 316SS Seat SS SS 316SS 316SS 316SS Seat Seal Determined by Soft Seat Selection Body WCB WCB CF8M CF8M WCB Spindle Guide 17- 4PH 17- 4PH 316SS 316SS 316SS Bonnet Seal Determined by Soft Seat Selection Spindle SS SS 316SS 316SS 316SS Open Lift Lever CS CS 316SS 316SS 316SS Packed Lift Lever CS CS 316SS 316SS 316SS Description 0 CSZ CSZ CSZ 1 CSZ CSZ CSZ 6 CSZ 316SS 316SS 7 CSZ CSZ CSZ 316SS SS 316SS SS WCB WCB Inconel® Inconel® 316SS SS 316SS SS 316SS SS 316SS SS 316SS 316SS SS SS WCB 316SS WCB 17- 4PH 316SS 316SS 316SS SS CS CS Materials: CS-Carbon Steel, SS-Stainless Steel, WCB -ASME SA 216, CF8M -ASME SA 351, CSZ - Carbon Steel - Zinc Plated + See page 7 for Lift Lever Component Identification and Seat Detail. 9 19 10 11 20 21 12 13 14 15 16 17 18 Hydroseal Legacy Series 9 Flanged Series Ball & Seat Safety Relief Valve General Design Features • 1"- 3" Inlet Sizes • Incorporates Hydroseal’s “Self-Seeking Soft Seat” Design • Operating Temperatures to 600°F • Soft Seat Option Provides Primary Seal with a Metal-To-Metal Secondary Seal • ASME Section VIII UV Code Stamped for Air & Gas • Available for Non-Code Liquid Applications Sizing Information Orifice Area ARV‡ AXV BV CRV# CV 0.196 0.248 0.441 0.785 0.785 Gas KD 0.31 0.25 0.40 0.22 0.22 Liquid KD 0.13 0.16 0.14 0.16 0.16 Slope 1.11 1.15 3.22 3.09 3.13 Liq. Flow Factor 1.0 1.5 2.4 4.9 4.9 Leak tested in accordance with factory standard. Contact Factory in order to receive sizing program and/or capacity charts. Water Capacities determined at 25% over set pressure. # Non-Code Below 18 psi ‡ Non-Code Below 21 psi Model Model Number & Dimension Data Model 1FL 5FL 6FL 2FL 3FL 4FL 7FL 8FL 9FL 10FL 11FL 13FL 14FL 20FL 22FL 21FL 23FL 24FL 25FL 28FL 29FL 26FL Inlet x Outlet 1x1 1 x 1 1/2 1x2 1 1/2 x 1 1/2 1 1/2 x 2 1 1/2 x 2 1/2 Flange Inlet x Outlet 150 x 150 600 x 150 600 x 600 150 x 150 300 x 150 600 x 300 1500 x 300 150 x 150 300 x 150 600 x 150 600 x 300 900 x 150 900 x 300 150 x 150 300 x 150 150 x 150 300 x 150 600 x 150 600 x 300 900 x 150 900 x 300 600 x 150 10 Hydroseal Legacy Series A 5 1/2 5 1/2 5 1/2 5 1/2 5 1/2 5 1/2 5 1/2 5 1/2 5 1/2 5 1/2 5 1/2 5 1/2 5 1/2 6 3/4 6 3/4 6 3/4 6 3/4 6 3/4 6 3/4 6 3/4 6 3/4 6 3/4 Dimension (in.) B C 4 5/8 12 3/4 4 5/8 12 3/4 5 4 /8 12 3/4 5 4 /8 12 3/4 5 4 /8 12 3/4 5 4 /8 12 3/4 5 4 /8 12 3/4 5 4 /8 12 3/4 5 4 /8 12 3/4 5 4 /8 12 3/4 5 4 /8 12 3/4 5 4 /8 12 3/4 5 4 /8 12 3/4 7 4 /8 15 1/2 7 4 /8 15 1/2 7 4 /8 15 1/2 7 4 /8 15 1/2 7 4 /8 15 1/2 7 4 /8 15 1/2 7 4 /8 15 1/2 7 4 /8 15 1/2 7 4 /8 15 1/2 Weight (lbs.) 20 26 28 24 24 28 28 22 26 28 30 31 34 32 34 34 36 39 42 50 52 45 30FL 36FL 37FL 38FL 44FL 47FL 31FL 33FL 39FL 40FL 42FL 45FL 32FL 34FL 35FL 41FL 43FL 46FL 50FL 51FL 52FL 53FL 54FL 60FL 61FL 62FL 63FL 64FL 65FL 66FL 67FL Inlet x Outlet 2x2 2 x 2 1/2 2x3 2 1/2 x 2 1/2 2 1/2 x 3 3x3 3x4 Flange Inlet x Outlet 150 x 150 600 x 150 600 x 300 600 x 600 1500 x 300 900 x 300 150 x 150 300 x 150 600 x 150 600 x 300 1500 x 300 1500 x 600 150 x 150 300 x 150 300 x 300 600 x 150 1500 x 300 900 x 150 150 x 150 150 x 150 300 x 150 600 x 150 600 x 300 150 x 150 300 x 150 300 x 300 600 x 150 600 x 300 150 x 150 300 x 150 600 x 150 A 6 7/8 6 7/8 6 7/8 6 7/8 8 1/8 8 1/8 6 7/8 6 7/8 6 7/8 6 7/8 8 1/8 8 1/8 6 7/8 6 7/8 8 1/8 6 7/8 8 1/8 8 1/8 8 8 8 8 8 8 8 8 8 8 8 8 8 Dimension (in.) B C 6 1/8 16 1/4 6 1/8 16 1/4 6 1/8 16 1/4 6 1/8 16 1/4 7 1/4 17 5/8 7 1/4 17 5/8 6 1/8 16 1/4 6 1/8 16 1/4 6 1/8 16 1/4 6 1/8 16 1/4 7 1/4 17 5/8 7 1/4 17 5/8 6 1/8 16 1/4 6 1/8 16 1/4 7 1/4 17 5/8 6 1/8 16 1/4 7 1/4 17 5/8 7 1/4 17 5/8 7 1/4 17 5/8 7 1/4 17 5/8 7 1/4 17 5/8 7 1/4 17 5/8 7 1/4 17 5/8 7 1/4 17 5/8 7 1/4 17 5/8 7 1/4 17 5/8 7 1/4 17 5/8 7 1/4 17 5/8 7 1/4 17 5/8 7 1/4 17 5/8 7 1/4 17 5/8 Weight (lbs.) 44 45 46 50 64 76 52 56 58 59 64 72 56 57 67 68 73 74 66 68 70 72 72 68 70 72 74 76 74 76 78 Flanged Safety Relief Valve, Parts List & Material Selection Part Number Codes 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Index Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Valve Cap Adjusting Screw Adjusting Lock Nut Cap Seal Bonnet Upper Spring Plate Spring Guide Stem Body Bonnet Seal Body Stem Lock Nut Lower Spring Plate Ball Seat Body/Seat Seal Open Lift Lever Packed Lift Lever + + 0 CS CS SS 1 CS CS SS WCB SS SS SS WCB SS 316SS SS WCB SS SS 440C SS WCB SS SS Stellite® SS CS CS CS CS Material Code 4 5 6 7 316SS CS CS CS 316SS 316SS 316SS CS 316SS 316SS 316SS SS Specify CF8M CF8M WCB WCB WCB 316SS 316SS 316SS 316SS SS 316SS Inconel® 316SS Inconel® Inconel® 316SS 316SS 316SS 316SS SS Specify CF8M CF8M WCB WCB WCB 316SS 316SS 316SS 316SS SS 316SS 316SS 316SS 316SS SS Stellite® Stellite® Stellite® Stellite® 440C 316SS 316SS 316SS 316SS SS Specify Cast SS Cast SS CS CS CS Cast SS Cast SS CS CS CS 3 316SS 316SS 316SS Materials: CS-Carbon Steel, SS-Stainless Steel, WCB - ASME SA 216, CF8M - ASME SA 351 + See page 5 for Lift Lever Component Identification and Seat Detail. Hydroseal Legacy Series 11 Brass Safety Relief Valve General Design Features • • • • For Air, Gas and Liquids Pressures up to 300 psi Temperatures to 350˚F 1/2" - 3" Inlet Sizes C A B Dimension Data Part Number Codes Model A A1 A2 B1 B2 C1 C2 D1 D2 E1 E2 F1 F2 G1 G2 H1 2 1/8 2 1/8 2 3/8 2 3/8 2 3/4 2 3/4 3 1/4 3 1/4 3 1/2 3 1/2 4 4 4 3/4 4 3/4 5 1/8 Dimension (in.) B C 68 & 78 69 & 79 1 3/8 6 1/2 5 7/8 1 3/8 6 1/2 5 7/8 1 3/8 6 7/8 6 1 3/8 6 7/8 6 1 7/8 7 1/2 7 1/2 1 7/8 7 1/2 7 1/2 2 8 1/2 8 1/2 2 8 1/2 8 1/2 2 1/2 9 3/4 9 3/4 2 1/2 9 3/4 9 3/4 2 5/8 11 1/8 11 1/8 2 5/8 11 1/8 11 1/8 3 1/8 13 1/4 12 3 1/8 13 1/4 12 4 3/8 15 13 1/2 68 & 78 3 3 3 3 4 4 5 5 7 7 10 10 22 22 23 69 & 79 2 2 2 2 3 3 4 4 6 6 9 9 21 21 22 Model Number & Dimension Data Model A1 A2 B1 B2 C1 C2 D1 D2 E1 E2 F1 F2 G1 G2 H1 Inlet x Outlet 1/2 x 1/2 1/2 x 3/4 3/4 x 3/4 3/4 x 1 1x1 1 x 1 1/4 1 1/4 x 1 1/4 1 1/4 x 1 1/2 1 1/2 x 1 1/2 1 1/2 x 2 2x2 2 x 2 1/2 2 1/2 x 2 1/2 2 1/2 x 3 3x3 Orifice Size Contact Factory in order to receive capacity charts. 12 Hydroseal Legacy Series Weight (lbs.) 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 Max Set (psig) 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 Brass Safety Relief Valve, Parts List & Material Selection Series 68 & 78 Index 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16* 17* Description Hood Lifter Nut Lift Lever Pressure Screw Lift Lever Pin Lock Nut Spring Plate Spring Spring Post Bonnet Disc Nut Disc Spring Post Support Ball Bearing Body Regulator Lock Screw Regulator Ring Series 69 & 79 Material Bronze Brass Bronze Brass Brass Brass Brass Stainless Steel Brass Bronze Brass Bronze Brass Stainless Steel Brass Brass Bronze Index 1 2 3 4 5 6 7 8 9 10 11 12 13 14* 15* Description Hood Pressure Screw Lock Nut Gasket Spring Plate Spring Spring Post Bonnet Disc Nut Spring Post Support Disc Ball Bearing Body Regulator Lock Screw Regulator Ring Material Bronze Brass Brass Teflon® Brass Stainless Steel Brass Bronze Brass Brass Bronze Stainless Steel Brass Brass Bronze *Series 79 Only. *Series 78 Only. Hydroseal Legacy Series 13 High Pressure “Y” Strainer General Design Features • Designed for High Pressure Applications Requiring an Easy Maintenance, Collapse Resistant Screen • In-Line Cleanout Access • Pressures to 3000 psi • 1/2"-2" FNPT & Socket Weld • Spiral Wound Stainless Steel Screen • Operating Temperatures to 400˚F A B Model Number & Dimension Data Part Number Codes Model YTS1 YTS3 YTS5 YTS8 YTS10 Screen Data 1 Screen X A B C Mesh 10 20 40 100 Inches .067 .033 .014 .006 Microns 1690 840 355 149 Parts List 2 3 Index Description 1 2 3 4 5 Body Screen Cap O-Ring Plug 14 Hydroseal Legacy Series Material Code 0 ASME SA 487 4A 304SS CS Viton® CS 3 CF8M 304SS 316SS Viton® 316SS 4 5 Inlet / Max Set Outlet (psig) 1/2 FNPT 3000 3/4 FNPT 3000 1 FNPT 3000 11/2 FNPT 3000 2 FNPT 3000 Dimension (in.) A B 5 1/8 4 5 1/8 4 5 1/8 4 7 1/ 2 5 3 /8 9 5/8 6 3 /8 Clean Out Plug (in.) 1/4 1/4 1/4 3/4 3/4 Weight (lbs.) 6 6 6 17 30 High Pressure Check Valve General Design Features • Designed for Applications Requiring a High Pressure Easy-To-Maintain Steel Check Valve • Easy Service Cartridge Barrel Design • Pressures to 3000 psi • Operating Temperatures to 400°F • 1/2"- 2" FNPT & Socket Weld A B Part Number Codes Model Number & Dimension Data /O Inlet utlet erial Mat on necti Specify Model Number (Right) Model 0 • Standard 3 • All 316SS CV50 CV75 CV100 CV150 CV200 Minimum opening pressure is 5 -7 psi. Blank • FNPT SW • Socket Weld on End C Inlet / Outlet 1/2 FNPT 3/4 FNPT 1 FNPT 1 1/2 FNPT 2 FNPT Max Set (psig) 3000 3000 3000 3000 3000 Dimension (in.) A B 5 1/8 4 7/8 5 1/8 4 7/8 5 1/8 4 7/8 7 1/ 2 5 3/8 9 5 /8 6 3/4 Weight (lbs.) 7 7 7 21 33 CV100 0 XX Example Parts List Index Description 1 Barrel Seal 2 Ball 3 Body 4 Spring 5 Body Seal* 6 Barrel 7 Cap Seal 8 Cap *Not used on CV150 & CV200. 1 Material Code 0 Viton® 440C ASME SA 487 4A 316SS Viton® 17- 4PH Viton® 4140 3 Viton® SS CF8M 316SS Viton® 316SS Viton® 316SS 2 3 4 5 6 7 8 Hydroseal Legacy Series 15 Worldwide Sales Offices Hydroseal, a leading brand of CIRCOR Energy, reaches into every corner of the globe serving the oil & gas and industrial marketplace. Supplying an extensive range of product offerings through a worldwide network of manufacturer representatives and distributors, Hydroseal is the right choice for all your pressure relief needs. World Headquarters Canada 1500 S.E. 89th Street Oklahoma City, OK 73149 USA Phone: (405) 631-1533 Fax: (405) 631-5034 E-mail: sales@circorenergy.com www.circorenergy.com 9430-39th Avenue, Edmonton Alberta, Canada T6E 5T9 Phone: (780) 463-8633 Fax: (780) 461-1588 E-mail: kfinfo@circorenergy.com www.circorenergy.com www.circorenergy.com Hydro-Legacy-Dec-11-2up-HP • ©2011 CIRCOR Energy • Hydroseal is a Brand of CIRCOR Energy • Litho USA • Hydroseal reserves the right to change designs, materials or specifications without notice or without obligation to furnish or install such changes on products previously or subsequently sold. • Stellite® is a registered trademark of Deloro Stellite. • Inconel® is a registered trademark of Special Metals Corporation, USA. • Viton® is a registered trademark of DuPont Dow Elastomers. • Kalrez® is a registered trademark of DuPont Performance Elastomers L.L.C. • Teflon® is a registered trademark of DuPont.
