installation instructions

PRESTO™ DLWL MR/4
installation instructions
installation: frame
This fixture is
listed, suitable for use in a fire rated ceiling, and should be installed in accordance with the National Electrical Code and local regulations.
WARNING: Do not install ceiling insulation within 3 inches of fixture sides nor above fixture in such a way to entrap heat.
Select a location in the ceiling where
•the ceiling material is 1 1/8” or less and capable of supporting a weight of 14 pounds along
the rim of the hole, and
•the recess depth is 6 1/4” or more from the finished ceiling line.
Cut a 5 1/8” diameter hole into the ceiling and bring service wires to a point adjacent to hole.
•Disassemble housing from frame by removing two hex nuts. Save nuts.
•Insert the frame into hole and insert the two brackets into the slots in each arm
of the frame. Position frame in relation to wall to be lit as shown in drawing.
Hold the frame up so that the flange makes contact with the underside of the ceiling and, while
supporting the frame
•push a bracket down its slot until it presses against the top side of the ceiling
•tighten the bracket screw.
Repeat the process for the second bracket.
wiring
This fixture is
listed and approved for 90°C branch circuit wiring.
•Pull service wires through frame aperture.
•Remove inner cover of the splice compartment by releasing spring.
•Splice the black service wire to the black lead.
•Splice the white service wire to the set of white leads.
•Splice the green service wire to the green lead.
•Do not disturb the blue lead splices.
•Put wire nuts on all open splices.
•Snap junction box cover back into place.
installation: splice compartment, housing and reflector
•Insert splice compartment through aperture. Position it so tab aligns with
slot in frame and lower it so tab enters
slot and clicks into place.
Note: Prepare housing for insertion into aperture by
sliding inner sleeve up into housing.
•Insert housing through aperture and
position it so that studs pass through
holes in top of housing.
•Tighten hex nuts onto studs.
•Pull inner sleeve down out of housing.
•Withdraw bead chain from housing and
clip to yoke.
•Withdraw socket from housing, insert
lamp into socket and slide lamp into
lamp holder.
Position the reflector assembly in relation to the wall
as shown in illustration.
•Push reflector, slowly and evenly, into
fixture.
©Edison Price Lighting, 41-50 22nd Street, Long Island City, NY 10022 www.epl.com ™Presto is a pending trademark of Edison Price Lighting 601280-00
Prepare the reflector assembly by unwrapping lens
and re-inserting lens into assembly.
protective glass
It is necessary that MR-16 lamps be operated behind a protective glass lamp guard. The lens shipped with the fixture, or any Edison Price Lighting Optical Accessory
(see below), serves this purpose. MR-16 lamps with integral cover glass require no protective glass lamp guard.
optical accessories
Optional Optical Accessories – including color filters and UV filters – are available for use in Presto DLWL MR/4 fixtures. Slide the Accessory into the
lamp holder, under the lamp.
reflector maintenance
The reflector and the glass accessories may be cleaned of dust with a damp, soft lint-free cloth. To remove fingerprints or dirt, wash with a solution of dishwashing
detergent and water, rinse, and dry with a soft lint-free cloth. Avoid wiping when reflector surface is dry.
Prestina
installation instructions
IMPORTANT
Prestina luminaires and fixtures are intended for use in a sheetrock ceiling.
Install the housing as shown on the enclosed (white) Installation Instructions.
Coordinate with the ceiling contractor to ensure that ceiling is finished as shown below.
Ceiling contractor: Secure spackle screen to sheetrock
with ¾” sheetrock screws.
Secure edges of spackle screen to sheetrock with selfadhesive fiberglass drywall joint tape.
Apply two coats of drywall compound, sanding between
coats. Be careful to leave the center of the protective
disc free of compound.
601100-X
Electrical contractor: When Prestina housing is installed,
the spackle screen should be touching the sheetrock at
all points.
Edison Price Lighting 41–50 22nd Street Long Island City, NY 11101 www.epl.com
©
5
6
Final sanding should leave the rim of the TF Ring exposed.
7
Remove protective disc by insering a screw driver or other sharp tool into the hole in disc and prying downward.
Make sure that the interior rim of the TF Ring is free of
compound (see detail).
Prime and paint.
8
Electrical contractor: Insert reflector into luminaire or
fixture aperture.