VISTA Video Collaboration Table™ Typical

A S S E M B L Y
I N S T R U C T I O N
M A N U A L
VISTA Video Collaboration Table
Typical
™
Assembly requires two people working together.
Video monitor and mounting bracket are not included and separately
purchased. Refer to your manufacturer’s video monitor mounting
bracket instructions for wall mounting to VISTA’s freestanding wall.
©2013 CBT Supply, Inc. dba SMARTdesks® All rights reserved.
SMARTdesks® is a registered trademark of CBT Supply, Inc.
www.smartdesks.com
800 770 7042
PARTS IDENTIFICATION
Please note that the VISTA Video Collaboration Tables for this installation
are NOT THE SAME. Each has been customized for its installation space. Be
sure that your parts are for the same MARK NUMBER.
One top banded on 3 sides
• Dimensions 72 x 50
• Top finish #7285-58 Violin Figured
Annigre
• Wood edge maple hardwood
stained to match
#7012-58 Amber Maple
• WF2 Edge Profile
Shelf (1 each)
9 deep
26 wood Dowels
12 per each vertical x 2
= 24 and two for each
equipment shelf = 26
Trapezoidal Back Wall
Trapezoidal Front Wall
Uprights (2 each)
58.75w x 74h
11.5 w x 74h
56w x 78h
Stand-Off Bars (6 each)
Fixed Pin Spanner Wrench
11.5” long x 1” diameter with threaded
inserts, plus 2 each tapped end caps.
Black Aluminum.
Used for tightening the Stand Off Bar End Caps
800 770 7042 SMARTdesks Technical Assistance 2
www.smartdesks.com
Keel Side Panels
2 total quantity
Table End Base
Panel(1 each)
Access Panel
2 total quantity
Keel Stretchers
4 total quantity
Male
Maxifix Cam
262.87.003
Maxifix End Pin
Female
262.87.781
Keku Clips
Maxi Fix End Bolt Pins 2 to go through
wall into wall end top
Keel Bottom (2 for each table top)
MaxiFix Cams 2 for tops
4 total quantity
This part fastens to side panels and keel This part fastens to side panels and keel Minifix Cam
Surface
Connector Female
262.26.623
Minifix End Pin
262.27.163
Mini Fix Pins 24 total = 8 for wall
panels (4) and equipment shelf
ends (4); 8 for Keel Bottoms; 8 for
stretchers in Keel.
262.70.431
This part fastens to side panels
and keel.
This part fastens to underside of top Surface Connector Male
262.70.413
This part fastens to underside
of top.
Surface connectors cannot be removed from their mounting holes. The females
will ship installed and the males will need to be inserted. This is done to reduce
confusion in assembly.
Surface Connectors : 9 per top, 3 each side of Keel (6); (3) on End panel.
800 770 7042 SMARTdesks Technical Assistance 3
This part fastens to underside of top www.smartdesks.com
Approach to Assembly
VISTA must be assembled in this order
to facilitate the installation of equipment. Coordinate with your IT specialists
so technology can be installed at the
proper stage. Assembly should be done
as close as possible to the final installation position to avoid putting stress on
the components.
1. The Keel Base Assembly is made
first, consisting of two Keel Side
Panels, one Table End Panel, and the
Keel Bottoms.
2. The Front Wall is tied into the Keel
Base Assembly so that it is freestanding.
3. Uprights and Shelf are applied
4. IT Specialists install components
and video monitor mount (not included). The video monitor mount
has its own installation instructions
for mounting to a wall. The VISTA
front wall should be structurally
sound for the load if robust bolts,
washers and nuts are used for
through bolt fastening. Installation
with wood screws is not recommended.
5. With VISTA in final position, install
the Table Top to the base and wall.
6. The very last thing to be installed is
the back wall. When installed there
is limited access to technology on
the shelf and the monitor mount.
To make changes to the technology
installation, the back wall should be
removed for service
7. If the VISTA needs to be moved to a
different location, disassemble and
reassemble in the desired location.
Orientation for assembled VISTA MARK 16 C
Uprights
and Shelf
Monitor and Mount
attach here
Back Wall
Front Wall
Table Top edged 3 sides
End Base Panel
Keel Base Assembly
800 770 7042 SMARTdesks Technical Assistance 4
www.smartdesks.com
Step 1
Make the Keel Base Assembly
Start by affixing the Keel Base Panels and Keel Stretcher
Panels to one side of the Keel. Use Minifix Pins and Cams.
Install the second Keel Base with pins and cams.
How Pins and Cams work
Install the Table End Panel with pins and cams.
The arrow of the cam points in the direction of the insertion
channel. The pin is inserted, and the cam is tightened with a
Phillips No. 2 screwdriver.
Keel Base Panels
Access Panel (pre-installed)
Keel Stretchers
Keel Bottoms
Table End Panel
MATERIAL:
FINISH:
EDGE:
72.000
50.000
30.000
ACCESS PANEL
T-EDGE CUTOUTS
Detail of Table.
Do not attach the top in step 1.
800 770 7042
SMARTdesks
ROOM:
205A (1) Technical Assistance FINISH: TOP: #7285 58, "Violin Figured Annigre"
WOOD EDGE: #7012 58 "Amber Maple"
MATCH WF2 EDGE PROFILE
5
SYM DATE
www.smartdesks.com
BY
REVISIONS
DESCRIPTION
TOLERANCES PART
UNLESS SPECIFIED
NAME
OTHERWISE
DECIMALS
DATE:
MARK 16C TABLE
DRWN BY:
514F Progress Drive
Linthicum, MD 21090
Step 2
Front Wall Assembly
To make a free-standing structure, tie the
front wall into the keel assembly with
Maxifix pins and cams. Do this in the final
position for the VISTA installation.
Maxifix Cam
262.87.003
Maxifix End Pin
262.87.781
Install the uprights and shelf
Use dowels to hold the uprights in place. Each upright uses 12 dowels.
Install the shelf to the uprights using 2 dowels to the front wall and 4
Minifix pins and cams.
Install the Standoffs to the front wall, screwing in the end caps with the
Fixed Pin Spanner Wrench.
Uprights
Dowels
Stand-Offs
Upon completion, if you are
working on Mark 15, tie in the
second Keel Assembly using
pins and cams.
At this point, coordinate with
IT to let them install the technology, including the Video
Monitor Mount.
Dowels
Stand-Offs
When it is time to mount CPU
holders, IT should notify that
the table tops can be applied.
Fixed Pin Spanner
Wrench
Shelf
Dowels
Stand-Offs
Used for tightening the
Stand Off Bar End Caps
800 770 7042 SMARTdesks Technical Assistance 6
www.smartdesks.com
Female surface connectors have
been pre installed in the Keel Side
Panels. Insert the Male Surface
Connectors into the holes drilled
on the bottom surface of the Table
Top.
Capture the Surface Connectors
and tighten the set screws.
30.000
Install the table top
ACCESS PANEL
T-EDGE CUTOUTS
Tie in Table Top
to Front Wall with
pins and cams
HumansScale CPU Holders will install to the
top in line with the Keel Scallops made for
cables to pass through the keel. The tops
must be installed before installing the CPU
Holders.
Access Panel
1 per Keel Side Panel
Male
The Access Panels ship preinstalled using Keku Clips.
800 770 7042 SMARTdesks Technical Assistance Female
Keku Clips
7
www.smartdesks.com
Install the back wall as the final step.
Back Wall
The back wall is the access panel for the monitor mount and the
technology that is placed on the shelf. While cables can be fished
through the Keel when complete, it takes less effort to do this
with the back wall and tops removed.
The back is applied with dowels and secured with Stand-Off End
Caps using the Fixed Pin Spanner Wrench.
Front Wall
•
•
•
•
Fixed Pin Spanner
Wrench
Used for tightening the
Stand Off Bar End Caps
•
•
800 770 7042 SMARTdesks Technical Assistance 8
www.smartdesks.com
9
(NOT RELEASED FOR PRODUCTION)
REFERENCE ONLY
FINISH: TOP: #7285 58, "Violin Figured Annigre"
WOOD EDGE: MAPLE HARDWOOD STAINED TO
MATCH #7012 58 "Amber Maple"
WF2 EDGE PROFILE
ROOM: 205A (1)
22X 8MM 10MM DEEP
BACKER SIDE
72
SYM
DATE
BY
REVISIONS
DESCRIPTION
2X 35MM .612" DEEP
BACKER SIDE
+
+
+
+
-
.X
.XX
.XXX
ANGLS
DECIMALS
UNLESS SPECIFIED OTHERWISE
TOLERANCES
CAD NO.
CNC NO.
This drawing is the property of CBT Supply, Inc. dba SMARTdesks
and contains proprietary information that is not to be used except in
the consideration of bids or proposals tendered herewith. Reproductions or
or copying of this drawing, in whole or part, is prohibited.
SCALE:
CHK'D BY:
MARK 16C TOP
DRWN.BY:
NOTICE:
8 1/4
EDGE:
FINISH:
MATERIAL:
SMART
desks
TM
DRAWING NO.
PRODUCT
GROUP
514F Progress Drive
Linthicum, MD 21090
800.770.7042
www.Smartdesks.com
3/8" WIDE X .59" DEEP TYP.
BACKER SIDE
DATE:
PART
NAME
7
7
C Copyright CBT Supply dba SMARTdesks
50
BACKER
9
800 770 7042 SMARTdesks Technical Assistance www.smartdesks.com
REV.
13.500
78.000
800 770 7042 SMARTdesks Technical Assistance 10
www.smartdesks.com
58.750
8.625
56.000
56.000
SYM DATE
13.500
BY
REVISIONS
DESCRIPTION
.X :_____
.XX :_____
.XXX :_____
ANGLE :_____
DECIMALS
EDGE:
FINISH:
MATERIAL:
DRWN BY:
CAD NO.
CNC NO.
MARK 16C WALL
PO# 7292
DRAWING NO.
PRODUCT
GROUP
514F Progress Drive
Linthicum, MD 21090
800.770.7042
www.Smartdesks.com
T-EDGE CUTOUT
NOTICE: This drawing is the property of CBT Supply, Inc. dba SMARTdesks
and contains proprietary information that is not to be usedexcept in
the consideration of bids or proposals tendered herewith. Reproductions
or copying of the drawing, in whole or in part, is prohibited.
DATE:
SCALE:
CHK'D BY:
TOLERANCES PART
UNLESS SPECIFIED
NAME
OTHERWISE
ROOM: 205A (1)
FINISH: Wall: #728558,"Violin Figured Annigre"
Back Wall: #701258, "Amber Maple" (matte)
74.000
REV.
800 770 7042 SMARTdesks Technical Assistance 11
www.smartdesks.com
ROOM: 205A (1)
FINISH: TOP: #7285 58, "Violin Figured Annigre"
WOOD EDGE: #7012 58 "Amber Maple"
MATCH WF2 EDGE PROFILE
BASE PANEL: #7285 58, "Violin Figured Annigre"
KEEL: BLACK LAMINATE
T-EDGE CUTOUTS
ACCESS PANEL
72.000
SYM DATE
BY
REVISIONS
DESCRIPTION
30.000
.X :_____
.XX :_____
.XXX :_____
ANGLE :_____
DECIMALS
DRWN BY:
CAD NO.
CNC NO.
MARK 16C TABLE
NOTICE: This drawing is the property of CBT Supply, Inc. dba SMARTdesks
and contains proprietary information that is not to be usedexcept in
the consideration of bids or proposals tendered herewith. Reproductions
or copying of the drawing, in whole or in part, is prohibited.
DATE:
SCALE:
CHK'D BY:
TOLERANCES PART
UNLESS SPECIFIED
NAME
OTHERWISE
50.000
EDGE:
514F Progress Drive
Linthicum, MD 21090
800.770.7042
www.Smartdesks.com
PO# 7292
DRAWING NO.
PRODUCT
GROUP
FINISH:
MATERIAL:
REV.
800 770 7042 SMARTdesks Technical Assistance 12
www.smartdesks.com
SYM DATE
BY
REVISIONS
DESCRIPTION
.X :_____
.XX :_____
.XXX :_____
ANGLE :_____
DECIMALS
DRWN BY:
CAD NO.
CNC NO.
MARK 16C
NOTICE: This drawing is the property of CBT Supply, Inc. dba SMARTdesks
and contains proprietary information that is not to be usedexcept in
the consideration of bids or proposals tendered herewith. Reproductions
or copying of the drawing, in whole or in part, is prohibited.
DATE:
SCALE:
CHK'D BY:
TOLERANCES PART
UNLESS SPECIFIED
NAME
OTHERWISE
EDGE:
514F Progress Drive
Linthicum, MD 21090
800.770.7042
www.Smartdesks.com
PO# 7292
DRAWING NO.
PRODUCT
GROUP
FINISH:
MATERIAL:
REV.