E-Line - Jura Capresso Parts

Transcription

Brew Group removal instructions for Jura C, E, and F series:
m
Suitable for the following Jura Impressa models
u.
co
JURA all IMPRESSA E, F, and C:
E-Line: E10 * E25 * E30 * E40 * E45 * E5 * E50 * E55 * E60 * E65 *
E70 * E74 * E75 * E80 * E85
F-Line: F9 * F90 * F70 * F5 * F50
C-Line: C5
1. Disclaimer:
ur
This service manual describes the expansion and overhaul of the
brewing unit of Jura E50. Services Unlimited Inc.Parts Guru is NOT
responsible for any errors in understanding and repairs or use of
these instructions by inexperienced users.
Pa
r
ts
G
2. Safety Warning:
A coffee machine uses water, heat, steam and electricity. Allow the
machine to cool before repairing or servicing the machine. The
thermo couples need up to 5 hours to cool down. Please work
carefully and wisely.
Read the instructions thoroughly before
taking on repairs.
Services Unlimited Inc./Parts Guru shall NOT be responsible for any
damages to the property or any personal injuries while repairing the
machine.
We sell only the Best espresso machines.
Guru's Choice: Jura XJ9, Jura Impressa X9 NSF; & Royal One Touch
We offer after sale service, parts, repairs & Tech support, like nowhere else
For Homes, Businesses, Restaurants, Corporate dining, Rentals, Catering & more
For routine maintenance of espresso machine: CLICK HERE for Espresso maintenance DOs & DON'Ts
m
co
u.
ur
Required Tools:
Pa
r
ts
G
Normal screwdriver, Phillips screwdriver, oval head wrench, pliers, Torx TX20 and TX15 Torx
(depending on model).
Brew group C,E,F,S series
Jura grinder temperature sensor
Magnet valve 110V
Click picture to order online. If the link is broken, it will open the Home page. If so, type the desription in Quick search to open the page.
For Jura parts, repairs & tech support, contact:
Services Unlimited, Inc./ Parts Guru
209 Walnut street, Lansdale, PA 19446
Phone: 215-362-7000 Fax: 215-361-7434
email: sales@partsguru.com
Online store www.shop.partsguru.com
Click Here to order parts online. If any link is broken, it will open the Home page. If so, type the
name of part in Quick search to find it.
Jura water tank outlet valve kit
co
Small gear brew drive motor
Hose clamps set of three
Brew group maintenance kit
Complete grinder 120V DC
Coffee outlet hose support
Pa
r
ts
E8 E9 Steam outlet
G
ur
Oval head key
u.
Jura membrane regulator hair pin type
m
Membrane regulator Clamp
type with 12" reinforced hose
Thermostat L=115C
Dial component
frother complete
Legis connetors Thermoblock
Drip tray E Series
Clearyl filter cartridge
Brew group Piston Oring pair with lube
Transformer for all models
Step down 120V-9V
Bullet tip nozzle
Click on the part to order online. If the link is broken, it will open the Home page. If so, type name of part in the Quick search to access.
Phone: 215-362-7000 Fax: 215-361-7434
G
ur
u.
co
m
Dismantling the Machine
Pa
r
ts
1. Unplug the machine. Remove the drip pans and water container.
Empty the coffee bean hopper, so no coffee beans fall into the machine.
m
co
u.
Pa
r
ts
G
ur
2. Use the oval head screw key to remove the oval head screws from the back of the machine.
Rotate the key counterclockwise.
3.
Unscrew the oval head screw gently without causing any damage to the machine.
Phone: 215-362-7000 Fax: 215-361-7434
m
co
u.
4. Remove the upper screws using the phillips or Torx screw driver. Rotate counter
Pa
r
ts
G
ur
clockwise
5. Remove the upper part completely carefully without damaging the side flaps
m
co
u.
6.Remove the left side panel by gently sliding it backwards to disengage the tabs from the
Pa
r
ts
G
ur
front panel. Once the tabs are unhooked, slowly remove the side panel.
7. Apply the same procedure to remove the right side panel as indicated in step 6.
Phone: 215-362-7000 Fax: 215-361-7434
m
co
u.
Pa
r
ts
G
ur
8. Remove the bolt from the brew drive gear motor using the Torx 20 or Phillips screw driver
(depending on the model). Be sure to use the correct tool to remove the screw. Using the
wrong tool may worn out the grooves hence making it difficult to remove the screw.
Jura Grinder key to unblock
Ring & Cone Grinder burrs
Phone: 215-362-7000 Fax: 215-361-7434
m
co
u.
9. Remove the hair pin clip from the heating cartridge valve on the right side of the machine
Pa
r
ts
G
ur
using the screw driver or the pliers.
10. Pull down the transparent silicone hose from the heater valve. Be sure to remove the
seal/o-ring at the end of the silicone hose. It often remains inside the valve and can
be removed using the screw driver.
m
co
u.
ur
11. Remove the screw from the water tank seal cover on the left side of the machine.
G
Pa
r
ts
Phone: 215-362-7000 Fax: 215-361-7434
m
co
u.
12. Slide out the water tank seal assembly slowly. No need to remove the hose inside the
Pa
r
ts
G
ur
assembly.
13. Cut the cable ties at the ground coffee funnel
m
co
u.
Pa
r
ts
G
ur
14. You may remove the gound coffee funnel but it's not necessary.
15. Unsrew the three highlighted screws using the phillips or Torx screw driver. Do not remove
any other screws that are attached to the brew group guide.
m
co
u.
ur
16. Slide out the brew group slowly. Ensure that infuser pipe out of the brew group
G
to the coffee dispensing assembly is detached.
ts
Pa
r
Phone: 215-362-7000 Fax: 215-361-7434
m
co
u.
Pa
r
ts
G
ur
17. Slide up the brew unit guide
18. Detach the infuser connector mounted atop the brew group. Leave the infuser hose attached
Phone: 215-362-7000 Fax: 215-361-7434
m
co
u.
ur
19. Detach the coffee sweeper/scraper from the brew group.
G
Pa
r
ts
Phone: 215-362-7000 Fax: 215-361-7434
m
co
u.
ur
G
ts
Pa
r
20. Brew Group without the brew group guide and coffee scraper.

E-Line - Jura Capresso Parts

Transcription

Similar documents

Ellicottville Fall Fest

Services Unlimited, Inc./ Parts Guru

Disassembly of a Jura Capresso Z5 Ceramic Valve January 12

Maintenance at the touch of a button for Dad this

December 2015 insert - Lansdale Historical Society

2016 summer activities

ESPRESSO MACHINE SHIPPING INSTRUCTIONS

HISTORICAL DVD COLLECTION - Lansdale Historical Society

Dear beloved members of our worldwide community

Jenkins Journal - Lansdale Historical Society

Evolution and geometry of the Jura mountains

Origin of the Jura Mountains

Developer Presentation

celebrates shri guru ravidass ji`s gurpurab

Kinetico 2060f Sulfur Guard System Non

December 2011 - Guru Nanak Multi Academy Trust

early discoverers xxvi another forgotten pioneer of the glacial theory

ETP Techno

Kick Up Your Kit By Marlon Lang

Newsletter

611 Koffee

When it absolutely, positively has to work