Removable prosthesis stabilisation MIB - MInI IMplant

simple - economical - practical
M.I.B. - Mini Implant Ball
Removable prosthesis
stabilisation
R e m o va b l e p r o s t h e s i s s ta b i l i s at i o n
INDICATIONS
ReFeRENCES
This implant allows the stabilisation of a whole removable mandibular or maxillar prosthesis. Its use will have to take into
account the following precautionary measures : the estimation of the different forces, the precise evaluation of the bone
volume and the rebasing of the removable prosthesis before the implant insertion.
These implants maintain the prosthesis in place. In no case they are meant to support the occlusion charges. The rebasing
will have to be done regularly in order not to loose the mucous supports.
Implants :
Lg 10 mm: ref. MIB V 26100 (per unit)
ref. MIB V 26100 4 (by 4)
Lg 12 mm: ref. MIB V 26120 (per unit)
ref. MIB V 26120 4 (by 4)
Lg 14 mm: ref. MIB V 26140 (per unit)
ref. MIB V 26140 4 (by 4)
SURGICAL STEPS :
3,35 mm
Analog
ref. IN MIB 003
3,3 mm
Ball for the removable
prosthesis fixing
Octagon for the
implant screwing
6
O’Ring female attachment
ref. HO O4840 (supplied with a
50 shores O’Ring)
Available separately by :
- 5 O’Ring 50 shores ref. HOO1415 50
- 5 O’Ring 60 shores ref. HOO1415 60
Ø 3,5 mm
Smooth machined
neck in contact with
the gingiva and the
junctional epithelium
Kit
ref. IN KTMIBMINI
> Click wrench
ref. IN CC
Sanded and etched
surface for a good
osteo-integration
Ø 2,6 mm
4.Pre-tightening of the MIB implant
with the implant holder. Tighten the
implant with a sight vertical pressure
toward the apical end.
This protocol starts the auto-tapping
process. As soon as the tightening
resistance is becoming too strong,
proceed to the next step.
> Rack
ref. IN SQ MIB
Accessories of the rack:
3 µm
5
Separating ring
ref. IN MIB 002
Including :
3.Assessment of the parallelism.
The guide can be maintained in
order to help the drilling tofollow.
4
Ø 5 mm
5.End the tightening of the implant
with the click - and tightening wrenches. The ideal in depth burying
of the MIB must let the implant’s
head go over the gingival without
any threading or apparent part of
the implant’s neck. The implant
can be buryied till its shows a
primary stability good enough for
immediate loading. If the tightening
of the implant is blocked before its
complete insertion, take out the
implant by reversing the direction
of rotation. Introduce the drill an
proceed to a little more drilling,
before placing the implant again.
- 1 drill Ø 2 mm
ref. IN FHI 20 130
- 1 O’ring wrench
ref. IN COIO
Anti-rotational and
self-taping groove
6. Implant and prosthesis in place.
©Anthogyr - MIB - 0710
2237 Avenue André Lasquin- 74700 Sallanches - France
Phone +33 (0)4 50 58 02 37 - Fax +33 (0)4 50 93 78 60
www.anthogyr.com
- 1 round bur
ref. IN FB 20
- 2 paralleling pins
ref. IN JPA
2,3 mm
- 1 gingival cutter
ref. IN MIB 001
TA6V Titanium
Implant, medical grade 5
Photos credits: Anthogyr - All rights reserved
3
2.Drilling with the Ø2 mm drill up
to 2/3 of the implant length with a
speed of 1000 to 1200 rpm with a
«coma-like» drilling.
Depending on the bone density, the
depth can be adapted in order to
optimize the primary retention of the
implant.
O’ring fitted out with a
silicone joint designed to
fix the prosthesis
2,8 mm
2
1.Incision made with the gingival
cutter. According to the visibility
required and the bone volume, the
opening of the flap is advised.
In presence of a thin ridge, the use
of a round bur may be necessary
and shall be used in order to mark
the bone before the next step (speed
from 1000 à 1200 rpm).
10 , 12 ou 14 mm
1