Bumper Boy Operating Manual

Table of Contents
Introduction
Operation
Electronics Overview
Mechanical Overview
Unload Procedure
Field Procedure
Safety
Key Definitions & Operation
Master Transmitter
Bumper Boy Receiver
Other functions (Skip Key, Sound/Launch, Auxiliary Jack, Motion, Advanced Sound, Auto Run)
Detailed Terminology of the Firing Assembly
Charging your Bumper Boy Electronics
LED Indicator Chart
Detail Features
Standard Sound
Advanced Sound Selection
Mounting Receiver on the Bumper Boy
Speaker Mounting
Auto Run Operation
Angle Adjustment
Controlling Height and Distance
Bi-Directional Configuration
Using Bango Birds
Third Party Launcher Control
Selecting Mode or Changing Modes
Mode Chart
Add Remote Launcher (pairing)
Adding an Auto Run Button (Pairing) or Changing the Time Delay Interval
Wet Weather Training
Maintaining your Bumper Boy
Troubleshooting
FCC Compliance
Terms of Use and Limitations of Liability
2
3
3
3
4
4
4
5
5
6
6
7
7
8
9
9
9
9
10
10
10
11
12
12
13
14
17
17
18
18
19
21
21
Introduction
How the system works
Whether you’re a hunter, field trainer, running hunt tests, using spaniels, pointers or retrievers, the Bumper
Boy system has proven to develop the best dogs in the world.
This reward-based system will have the largest impact on your dog’s ability to remember, retrieve, hunt,
build desire and learn. This unique training system will provide your dog with a more enjoyable training
experience, and help the dog learn faster. Whether you are teaching “sit to flush” or complicated multiple
marks, you and your dog can look forward to increased enjoyment and more effective use of time.
Bumper Boy units are mechanical devices, and require you to learn how to maintain them, as well as doing basic repair. All units are designed for field repairs; users should have a test kit, and understand how to
check and replace servos. Please visit www.bumperboy.com/support_trainingvideos.php for support
videos. This is a requirement to obtain maximum performance of this training system.
This sporting dog system is designed to simulate visual and audio dynamics of a human training assistant, and
the rapidly changing environment of a hunting experience. Bumper Boy is a total training and hunting system.
Electronically powered by Hawx Oudoors Inc., this system offers every training control possible, including
multiple launcher control. As well, you can add an e-collar and the Dog & Gun™ hunting control, exclusively
offered by Hawx Outdoors. Visit the
website at www. hawxdoggun.com
for the most cost effective & advanced
system.
Like any new training tool, the dog should
be introduced to it properly. Introduce
the new type of bumper; it may smell and
fly differently than the bumpers you use.
In some cases the dog thinks the flapping
bumper is a live flyer and will hunt to find
a bird. This is temporary and is quickly
learned. Then introduce images, different sounds, motion, and sound of shot.
This can be accomplished in normal yard
training. Now you will see your dog’s eyes
light up every time you use your
Bumper Boy. These electronics offer one-mile and .5 mile ranges. The receiver supports Bumper Boy multiple
launcher systems, advanced sound, motion, as well as any other third party launching system.
All in One Training / Hunting
2
Electronic Overview
Master Transmitter
(set on mode 18)
Selector Dial
Upper Button
(Launch)
Lower Button
(Sound)
Side Button
(Sound/Launch Combo)
Customizing Mode Button
Dog & Gun
Switch
Receiver
Step 1 Press the On Key on the Receiver.
Step 2 Select your launcher via the selector dial.
Step 3 Step 4 -
Press reload after your test to reset back
to the beginning of the order.
Press the function button on the remote
that you would like.
Press the Off button to save power when not in use.
Mechanical Overview (Loading)
Step 1 - Disengage the angle adjustment rod from the firing plate.
Step 2 - Rotate the firing plate
and barrel 180 degrees, so the
breech and servo assembly are up,
and the barrel is down. Unlatch the
firing plate and open the breech.
Step 3 - Insert a .22 cal blank
cartridge and close the breech.
Step 4 - Rotate the firing plate to the
launch position. Secure the firing plate to
the angle adjustment rod. Slide the
bumper onto the barrel.
3
Step 5 - Adjust the angle of the bumpers using the angle
adjustment rods to meet your training scenario needs, as
shown here. 85 Degrees is most common.
Step 6 - Cock the firing pins; pull down, making sure
you never lean out over the unit.
Unload procedure
Launcher should never be moved when firing pins are cocked.
There are two ways to unload:
1. First, use the electronics and fire off the bumpers.
2. Unlatch firing assembly carefully without leaning over
unit. When the assembly is open, remove shell and
release the firing pin with the electronics.
8 and 12 Shooter Re-Loading:
For your 8, or 12 shooter launcher, remember that when reloading, start from the bottom and work your way up. Then,
once all the shells are in, close the firing mechanisms from the
top, down, following that sequence.
Field Procedure (Tailgate Test)
• Turn on launcher receiver.
• Insert shells (do not cock the unit)
• Attach angle adjustment rods.
• Test all servos with the Transmitter.
• Press Reload on receiver.
You are now ready for the field setup. Use fire protector mat if required. Use the legs to press the unit into
the ground. Insert the bumpers. Cock firing pins – pull down, making sure to never lean over your unit. You
are now ready to run your dog(s).
Safety
The launcher can project bumpers at life threatening velocities. When loaded, it can be as dangerous as a
gun. It should be treated like a weapon.
• Children should not have access to the equipment or ammunition.
• At no time should you lean over the launcher during the loading process
• Turn the power on before loading the launcher to stabilize the electronics.
• When cocking the launcher, make sure each trigger is positively
engaged (listen for the click).
• Never point the launcher at anything except the sky.
• Never move the launcher when loaded.
• Clear the breech of shells when you have finished your training.
• Use fire protection or do not use the launcher, if training in dry
conditions. Hot air or sparks could cause grass fires. We recommend
that you use a mat underneath your unit if training in these
conditions as pictured to the right:
4
Key Definitions & Operation
Master Transmitter
Front
1. Selector Dial
Allows you to operate multiple launchers to a maximum of 6 launchers of any type.
“N” locks out keys, or provides a safety feature.
2. Dual Function Indicator Light
Indicates that a signal has been sent to activate a command on the receiver. In addition serves as
a low-battery indicator.
3. Toggle Switch
This switch is factory set (mode 18) to control
Launcher receivers (down) and e-collar (up).
4. Upper Button
This button is factory set to deliver Launch
command.
5. Lower Button
This button is factory set to deliver Sound
command.
6. Side Button
This button is factory set to deliver Sound, then
Launch (Other modes provide motion control,
or auto run control)
7. Dog and Gun Switch (DG Position)
This allows a Dog & Gun Transmitter to provide the Auto Run feature.
Auto Run automatically launches multiple units, just like a hunt test, or
field trail. Four launchers can be run (see Auto Run feature page 10).
DG - Dog & Gun mode. T - Training Mode.
8. Customizing Mode Button
This allows you to customize the system from factory settings.
Customization for different key positions.
9. Charging Jack
Plug in the charger here to start charging.
5
Bumper Boy Receiver
Reload Button – Pressing the reload
button resets the launcher to the start of
the firing order. The reload button must be
pressed every time you reload. A red light
confirms the reload command.
On/Off Button – Momentary pressing of
this button turns the receiver switch on,
and resets the firing order. The light will
flash periodically while the receiver is on.
Pressing again will turn the receiver off.
Switch the receiver off when not in use to
conserve battery power.
Pair Button – For adding a new
receiver to the Transmitter.
Sound Select Button – Press to select the
sound you desire.
Auxiliary Output Jack – This secondary Auxiliary jack on the side of the unit is for third party devices, which
produces 6 volts, activated by the launch button.
Charging Jack – Receiver power adapter Y plugs are used to charge, to AC Charge or Car charger.
Advanced Sound – This is a two position plug for the Digital sound (horn) speaker.
Standard Sound/Motion – This is a four position plug for the standard sound (piezo) speaker, and for
motion control (6 volt). This is operated from the sound, or motion button, on the Transmitter.
Servo Connector – This is the Bumper Boy servo connection. Left to right 9 to 12, 5 to 8, and 1 to 4 servos.
Other Functions
Skip Key – This is used to change the firing order in bi-directional mode in 4 shooter operation, allowing you
to fire in the same direction. It skips a servo, then launches the next servo in the order, and then operates
the skipped servo. Available in modes 17 and 27.
Sound/Launch – Provides a sound, and then a launch, by just pressing one key. Available in modes 18, 19,
20, 23, 26 and 27.
Auxiliary Jack – Third party 6-8 volt control for bird release devices.
Motion – Provides a 360 degree servo control with rotary motion of devices, or 6 volt control.
Advanced Sound – Duck, pheasant, human, or goose sounds available. See page 9.
Auto Run – Automatically runs multiple launchers as you would in a field trial or hunt test. See page 10.
6
Detailed Terminology of the Firing Assembly
‘o’ ring
barrel
thread rod insert
latch
firing plate
latch spring
lever arm
.
shell breech
shell ejector
lever pin (brass)
servo arm
firing pin
servo bracket
servo screw
servo motor
servo connector
lever bolt & nut
lever spring
firing assembly
retaining ring
cocking handle
Charging your Bumper Boy Electronics
Step 1 – Lift the rubber cover on the transmitter,
protecting the charging jack.
Step 2 – Connect the Transmitter Charging Wire to the
Master Transmitter or receiver.
Step 3 – Connect the AC Adapter, or car charger, to the
Charging Cradle. Plug the AC adapter, or car charger, into
a 120V AC outlet, or car power source.
Step 4 – You will see the LED flash every 2 seconds. The
charging of the units takes 2-3 hours for their first charge.
Step 5 – LED stops flashing when the units are fully charged,
and will automatically turn off when the charging is complete. Now, replace the rubber cover on the Transmitter.
7
LED Indicator Chart
Transmitter Indication LED
Mode
Operation
LED Color
Charging
Red
Button pressed
Green
flashes once
Pairing initialized
Green
light is solid
Pairing pending
Orange
light is solid
Run Mode
Green
flashes twice
every 4 seconds
Change Stimulation
Level in Run Mode
Orange
light is solid
Train
Dog &
Gun
LED Status
flashes every
3 seconds
Bumper Boy Receiver Indicator
Operation
LED Color
LED Status
flashes every
3 seconds
Charging
Red
Pairing Mode
Red
light is solid
Run Mode
Green
flashes twice
every 4 seconds
Sound Select
Red
light is solid
Transmitter and Receiver Battery Life Indicator (Fuel Gauge)
The LED will be flashing green when the units are turned on.
• Green when the batteries are full
• Red when the batteries are 80% discharged and will need charging soon (approximately 3-4 hours)
• Rapid red flashing means the batteries are completely dead. The Transmitter may lose range.
Low Battery Indication
Indication lights will turn from Green to Red, indicating Low Battery.
8
Detail Features
Standard Sound
Piezo Speaker
The standard (piezo electric) sound is plugged into the 4
prong outlet of the receiver. This produces a non-digital
sound that sounds like an electronic chirping noise (not
as good in windy conditions, or as directional for the dog).
This can be upgraded to Advanced sound, seen below.
Advanced Sound
Enhance the experience of your training with sound, and use it to help you accomplish
your training goals. Found to be a key tool in remote training, 80% of all Bumper Boy users
use the loud Duck call, or the human call of Hey to provide increased desire during
marking and training. This digital sound is very loud, and uses a horn speaker, which can be
heard at long distances.
Selecting Sounds
Step 1 - Press the On/Off key to turn the receiver on.
Step 2 - Push the sound select button until the light indicates
the selection that you would like. Choose from Duck, Pheasant,
Human, or Goose.
Note: Sound selection will be remembered from the last selection.
Standard Sound - This does not require selection,
just plug the small standard (piezo) speaker into the plug-in.
Horn Speaker
Mounting receiver
1. Plug servo connector firmly into the larger connector
pin, until snap is engaged. To remove, use needle nose
pliers and press tab in on back connector.
2. Place receiver on launcher, then insert washer, then the
nut and tighten. Receiver will remain loosely mounted
to the launcher. This is necessary to reduce recoil.
3. Mount speaker to frame.
4. Use wire fastening bracket and screw into place. Make sure to fasten all wirings including speakers.
5. See videos on www.bumperboy.com for more information
Speaker Mounting
Advanced Sound Speaker (horn speaker)
1. Attach the spring mount bracket to the launcher (mounting holes are located to the left of the receiver
on a 2/4 shooter and to the right on an 8/12 shooter).
9
2. Insert the end of the 2” bolt into the center hole of the
spring mount bracket. Install large washer,
split washer, and tighten nut.
3. Remove the wire hold-down bar from the receiver and
plug the two-pole male speaker connector into
the two-pole speaker connection on the receiver
(labeled “Adv. Sound”)
4. Arrange the speaker wire as picture (make sure the
knot is positioned above the slot) and replace the wire
hold-down bar.
5. Use the wiring strap to secure excess wire. Leave sufficient
slack to permit rotating the speaker.
Standard Sound Speaker
1. Attach the spring mount bracket to the launcher (mounting holes
are located to the left of the receiver on a 2/4 shooter and to the
right on an 8/12 shooter).
2. Determine the direction that you would like the speaker to point to
and insert the two small bolts into the appropriate holes on the
spring mount bracket. Attach the nuts and tighten.
3. Remove the wire hold-down bar from the receiver and plug the
four-pole male speaker connector into the four-pole speaker
connection on the receiver (labeled “Std. Sound”)
4. Arrange the speaker wire as pictured (make sure the knot is positioned above the slot) and
replace the wire hold-down bar.
5. Use the wiring strap to secure excess wire. Leave sufficient slack to permit rotating the speaker.
Auto Run Operation
Runs multiple launcher units like a field trial. Now you can set
your Auto Run to a customizable delay sequence, ranging from
1 - 6 seconds, and customizable sound / launch combo feature.
Auto Run uses the DG remote control button (mode DG Button).
Hands Free Operation
Auto run mode launches multiple units with a customizable
sequential delay between marks (1 - 6 seconds). Launch and
sound can be configured.
Operation features:
Start – Put the Transmitter in DG mode, the light will flash.
Press once to start (3 second delay)
Pause – Press again to pause
Resume – Press again – will continue the sequence
Reset – Turn the switch from DG mode to Training mode (T) and then back to the DG mode.
Quad Capable (Example):
Start (3 second delay)
Launch your first mark with, or without sound (delay set at 3 seconds)
Launch your next mark (you can launch 4 marks in this example)
See page 17 for pairing and set up for Auto Run or Dog & Gun setup.
10
Dog Gun
Remote Control
Mounting Options
Note: Other third party mounts are available for all-in-one training.
See www.hawxdoggun.com for details.
Dog & Gun Mega-Whistle Control
Control at your fingertips while training. Multiple dog/gun controls
can be added to your training whistle, allowing you lightweight,
and fast action access to stimulation control. This can be purchased
online at our store!
Auto run mode launches
multiple units with a customizable sequential delay between marks
(1 - 6 seconds). Launch and sound can be configured.
Angle Adjustment
The optimum angle of the barrels is between 55 and 85 degrees from the horizontal.
Increasing that angle will cause the bumper to travel higher, and shorten the range to
bumper impact. Reducing the angle will result in a lower trajectory.
The best position is above 85 degrees.
Controlling Height and Distance
Not placing the bumper all the way down on the barrel, or using a spacer tube
to stop the bumper, can achieve reducing the power of the flight of the bumper.
Doing so will lower the height of the shot, sometimes used for puppy training
scenarios. However, the longer the mark, the higher the shot should be.
Greater distances
The best way to achieve this is to reduce air friction. One method is to cut the streamer length ways or use a
lighter bumper like a dummy launcher bumper. The range to the point of impact may be varied from 10 to
50 yards or more.
Bi-Directional Configuration
The Bumper Boy 2 and 4 shooter systems can be configured to launch the bumpers
in one direction, or in opposite directions. The unit is shipped with all launcher
barrels oriented in the same direction. To configure the unit to
launch bumpers in opposite directions, proceed as follows:
Step 1 - Remove the three wing nuts and their
associated washers and lock washers. Remove the
end plate. Move the angle adjust rod to the
opposite side. On 4 shooters, the middle adjustment
rod must be remove/re-installed on the bottom frame.
11
Step 2 - Remove and re-install the firing
assembly so that they are in the opposite
direction. Re-install end plates, all washers,
and wing nuts.
Skip Feature – This feature was designed for bi-directional
mode. If your dog missed a mark you can now repeat the mark
in the same direction with the use of the Skip Key.
Sound, then launch will occur.
Using Bango Birds
Bango birds are synthetic birds to which balloon type targets
can be attached, and shot at with a shotgun and trap type load,
usually #8. Bango is an exciting, skill testing sport in which the
shooter and the dog can both be challenged.
Third Party Launcher Control
Option 1 – Supports any third party launcher with a separate
receiver, or sharing a Bumper Boy receiver. Aux output jack is
operated by the launch button on the transmitter.
Option 2 – Using the four prong plug, one side can be used to
support one aux device and would be controlled by the motion
key. Make sure you pick a model from the mode chart that has a
motion feature.
If you want to connect another aux device, use
another connection which would be controlled by the sound
button on the Transmitter (lower button).
This would mean you can’t use standard sound, and advanced
sound would be shared, meaning the sound and the winger
would operate together.
Option 3 – In this scenario, you can order a wiring harness to
drive up to 12 aux devices, however, they will be driven in the
same way as Bumper Boy servos are driven.
12
Selecting mode or changing modes
Hawx electronics provide up to 27 different modes, to provide custom key functions for any kind of training or hunting environment. In addition, if you can’t find the mode that meets your requirements, you can
request a custom mode. Bumper Boy can custom program your unit. The transmitter comes factory set on
default mode 18. See mode chart on page 14 for details.
Setting Modes
13
Mode Chart and Remote Training Systems
NOTE: The Transmitter is set at factory default, on mode 18 Launch (Upper Button), Sound (Lower Button)
and Sound / Launch Combo (Side button), toggle switch down to control the launcher.
From the configuration chart, pick the mode that best fits your type of training style or hunting style.
Note the mode # you would like to select and note the 3 values.
ͲŽůůĂƌDŽĚĞƐKƌŝĞŶƚĂƚĞĚƚŽŽŶƟŶƵŽƵƐ
Mode
hƉƉĞƌƵƩŽŶ
(level set by
intensity dial)
>ŽǁĞƌƵƩŽŶ
ĨƵŶĐƟŽŶ
(level set by
intensity dial)
^ŝĚĞďƵƩŽŶĨƵŶĐƟŽŶ
(level set by intensity
dial)
Toggle
ƐǁŝƚĐŚ (up/
down)
Toggle
ƐǁŝƚĐŚ
^ĞůĞĐƚŽƌ
Dial
&ƵŶĐƟŽŶ
ƵƩŽŶ
ƐĞůĞĐƟŽŶ
1
High
ŽŶƟŶƵŽƵƐ
DĞĚŝƵŵŽŶƟŶƵŽƵƐ
High Momentary
2-dog
Up
1
Upper
2
Medium
ŽŶƟŶƵŽƵƐ
>ŽǁŽŶƟŶƵŽƵƐ
Medium Momentary
2-dog
Up
1
Lower
3
High
ŽŶƟŶƵŽƵƐ
>ŽǁŽŶƟŶƵŽƵƐ
Medium Momentary
2-dog
Up
1
Side
4
Medium
ŽŶƟŶƵŽƵƐ
>ŽǁŽŶƟŶƵŽƵƐ
,ŝŐŚŽŶƟŶƵŽƵƐ
2-dog
Up
2
Upper
E-Collar Modes Orientated to Momentary
Mode
hƉƉĞƌƵƩŽŶ
(level set by
intensity dial)
>ŽǁĞƌƵƩŽŶ
ĨƵŶĐƟŽŶ
(level set by
intensity dial)
^ŝĚĞďƵƩŽŶĨƵŶĐƟŽŶ
(level set by intensity
dial)
Toggle
ƐǁŝƚĐŚ (up/
down)
Toggle
ƐǁŝƚĐŚ
^ĞůĞĐƚŽƌ
Dial
&ƵŶĐƟŽŶ
ƵƩŽŶ
ƐĞůĞĐƟŽŶ
5
High
Momentary
Medium Momentary
,ŝŐŚŽŶƟŶƵŽƵƐ
2-dog
Up
2
Lower
6
Medium
Momentary
Low Momentary
DĞĚŝƵŵŽŶƟŶƵŽƵƐ
2-dog
Up
2
Side
7
Medium
Momentary
Low Momentary
High Momentary
2-dog
Up
3
Upper
8
Medium
Momentary
Low Momentary
,ŝŐŚŽŶƟŶƵŽƵƐ
2-dog
Up
3
Lower
E-Collar Modes Orientated to Tone/Vibrate
14
Mode
hƉƉĞƌƵƩŽŶ
(level set by
intensity dial)
>ŽǁĞƌƵƩŽŶ
ĨƵŶĐƟŽŶ
(level set by
intensity dial)
^ŝĚĞďƵƩŽŶĨƵŶĐƟŽŶ
(level set by intensity
dial)
Toggle
ƐǁŝƚĐŚ (up/
down)
Toggle
ƐǁŝƚĐŚ
^ĞůĞĐƚŽƌ
Dial
&ƵŶĐƟŽŶ
ƵƩŽŶ
ƐĞůĞĐƟŽŶ
9
High
ŽŶƟŶƵŽƵƐ
Medium Momentary
Tone/Vibrate
2-dog
Up
3
Side
10
High
ŽŶƟŶƵŽƵƐ
High Momentary
Tone/Vibrate
2-dog
Up
4
Upper
11
Medium
ŽŶƟŶƵŽƵƐ
Medium Momentary
Tone/Vibrate
2-dog
Up
4
Lower
12
Medium
Momentary
Low Momentary
Tone/Vibrate
2-dog
Up
4
Side
E-Collar Modes Orientated to 3 or More Dogs
Mode
13
14
15
hƉƉĞƌƵƩŽŶ
(level set by
intensity dial)
>ŽǁĞƌƵƩŽŶ
ĨƵŶĐƟŽŶ
(level set by
intensity dial)
^ŝĚĞďƵƩŽŶĨƵŶĐƟŽŶ
(level set by intensity
dial)
Toggle
ƐǁŝƚĐŚ (up/
down)
Dog 1
Dog 2
Dog 3
High
ŽŶƟŶƵŽƵƐ
Dog 1
Dog 2
Dog 3
Medium
Momentary
Dog 1 High
ŽŶƟŶƵŽƵƐ
ŽŐϮ,ŝŐŚŽŶƟŶƵŽƵƐ
Dog 3 High
ŽŶƟŶƵŽƵƐ
Dogs 1-3
Dog 4 High
ŽŶƟŶƵŽƵƐ
ŽŐϱ,ŝŐŚŽŶƟŶƵŽƵƐ
Dog 6 High
ŽŶƟŶƵŽƵƐ
Dogs 4-6
Dog 1 High
Momentary
Dog 2 High
Momentary
Dog 3 High
Momentary
Dogs 1-3
Dog 4 High
Momentary
Dog 5 High
Momentary
Dog 6 High
Momentary
Dogs 4-6
Toggle
ƐǁŝƚĐŚ
^ĞůĞĐƚŽƌ
Dial
&ƵŶĐƟŽŶ
ƵƩŽŶ
ƐĞůĞĐƟŽŶ
Up
5
Upper
Up
5
Lower
Up
5
Side
All-In-One Training Systems E-Collar / Remote Control
Mode
hƉƉĞƌƵƩŽŶ
(level set by
intensity dial)
16
17
18
&ĂĐƚory
ĞĨĂƵůƚ
19
20
>ŽǁĞƌƵƩŽŶ
ĨƵŶĐƟŽŶ
(level set by
intensity dial)
^ŝĚĞďƵƩŽŶĨƵŶĐƟŽŶ
(level set by intensity
dial)
Toggle
ƐǁŝƚĐŚ;ƵƉͬ
down)
High
Momentary
ƐƟŵƵůĂƟŽŶ
Low Momentary
,ŝŐŚŽŶƟŶƵŽƵƐ
Dog 1
>ĂƵŶĐŚ
Sound
DŽƟŽŶͬƵdžŝůŝĂƌLJϮ
Launcher
1-6
High
Momentary
ƐƟŵƵůĂƟŽŶ
Low Momentary
,ŝŐŚŽŶƟŶƵŽƵƐ
1 dog
>ĂƵŶĐŚ
Sound
Skip
Launcher
1-6
High
Momentary
ƐƟŵƵůĂƟŽŶ
Medium Momentary
,ŝŐŚŽŶƟŶƵŽƵƐ
1 dog
>ĂƵŶĐŚ
Sound
Sound and Launch
Launcher
1-6
High
Momentary
ƐƟŵƵůĂƟŽŶ
Medium Momentary
DĞĚŝƵŵŽŶƟŶƵŽƵƐ
1 dog
>ĂƵŶĐŚ
Sound
Sound and Launch
Launcher
1-6
High
ŽŶƟŶƵŽƵƐ
ƐƟŵƵůĂƟŽŶ
>ŽǁŽŶƟŶƵŽƵƐ
High Momentary
1 dog
Sound and Launch
Launcher
1-6
>ĂƵŶĐŚ
Sound
Toggle
ƐǁŝƚĐŚ
^ĞůĞĐƚŽƌ
Dial
&ƵŶĐƟŽŶ
ƵƩŽŶ
ƐĞůĞĐƟŽŶ
Up
6
Upper
Up
6
Lower
Up
6
Side
Down
1
Upper
Down
1
Lower
15
Mode
hƉƉĞƌƵƩŽŶ
(level set by
intensity dial)
21
High
ŽŶƟŶƵŽƵƐ
ƐƟŵƵůĂƟŽŶ
22
23
24
25
26
>ŽǁĞƌƵƩŽŶ
ĨƵŶĐƟŽŶ
(level set by
intensity dial)
^ŝĚĞďƵƩŽŶĨƵŶĐƟŽŶ
(level set by intensity
dial)
Toggle
ƐǁŝƚĐŚ;ƵƉͬ
down)
>ŽǁŽŶƟŶƵŽƵƐ
Medium Momentary
1 dog
>ĂƵŶĐŚ
Sound
DŽƟŽŶͬƵdžŝůŝĂƌLJϮ
Launcher
1-6
High
ŽŶƟŶƵŽƵƐ
ƐƟŵƵůĂƟŽŶ
High Momentary
Vibrate/Tone
1 dog
>ĂƵŶĐŚ
Sound
DŽƟŽŶͬƵdžŝůŝĂƌLJϮ
Launcher
1-6
High
ŽŶƟŶƵŽƵƐ
ƐƟŵƵůĂƟŽŶ
High Momentary
Vibrate/Tone
1 dog
>ĂƵŶĐŚ
Sound
Sound and Launch
Launcher
1-6
Dog 1
High Momentary
Dog 2
High Momentary
Dog 3
High Momentary
3 dog
>ĂƵŶĐŚ
Sound
DŽƟŽŶͬƵdžŝůŝĂƌLJϮ
Launcher
1-6
Dog 1
,ŝŐŚŽŶƟŶƵŽƵƐ
Dog 2
,ŝŐŚŽŶƟŶƵŽƵƐ
Dog 3
,ŝŐŚŽŶƟŶƵŽƵƐ
3 dog
Launch
Sound
DŽƟŽŶͬƵdžŝůŝĂƌLJϮ
Launcher
1-6
Dog 1
,ŝŐŚŽŶƟŶƵŽƵƐ
Dog 2
,ŝŐŚŽŶƟŶƵŽƵƐ
Dog 3
,ŝŐŚŽŶƟŶƵŽƵƐ
3 dog
>ĂƵŶĐŚ
Sound
Sound and Launch
Launcher
1-6
Toggle
ƐǁŝƚĐŚ
^ĞůĞĐƚŽƌ
Dial
&ƵŶĐƟŽŶ
ƵƩŽŶ
ƐĞůĞĐƟŽŶ
Down
1
Side
Down
2
Upper
Down
2
Lower
Down
2
Side
Down
3
Upper
Down
3
Lower
Toggle
ƐǁŝƚĐŚ
^ĞůĞĐƚŽƌ
Dial
&ƵŶĐƟŽŶ
ƵƩŽŶ
ƐĞůĞĐƟŽŶ
Down
3
Side
Remote Training Systems
16
Mode
hƉƉĞƌƵƩŽŶ
(level set by
intensity dial)
>ŽǁĞƌƵƩŽŶ
ĨƵŶĐƟŽŶ
(level set by
intensity dial)
^ŝĚĞďƵƩŽŶĨƵŶĐƟŽŶ
(level set by intensity
dial)
Toggle
ƐǁŝƚĐŚ;ƵƉͬ
down)
27
>ĂƵŶĐŚ
ĚǀĂŶĐĞĚ^ŽƵŶĚ
Sound and Launch
Launcher
1-6
Ƶdžϭ
DŽƟŽŶͬƵdžϮ
Skip
Launcher
1-6
Add Remote Launcher (Pairing)
Step 1 - On the Bumper Boy receiver,
press the Pair button. The indication
light will go red.
Step 2 - Select the correct
toggle switch (up, down) in
accordance to the Mode
Chart (see pages 14 to 16)
Note: Transmitter should
be in Training Mode.
Step 3 - Set the
Selector Intensity
dial to your desired
launcher number.
Step 4 - Press any button (Upper, Lower or Side).
The pair indicator light on the receiver will turn off.
This indicates the launcher is now paired, and turned on.
Adding an Auto Run Button (Pairing) or Changing the Time Interval
Step 1 - Set the Transmitter to DG mode. Press any
Step 2 - Set the toggle switch
to the Launcher position (please
refer to the mode chart).
button to activate. The transmitter will flash green
every 4 seconds.
Step 3 - Press and release the Mode
Button with a pen on the back of the trans
mitter. Green light turns on, and the
transmitter is now in Auto Run
pairing mode.
Step 4 - Set the delay (time
between launch) by using the rotary
dial 1 to 6 seconds.
Step 5 (Launch only) - Select and
Press the Upper button (launch only, silent mode).
Then the green light turns orange.
OR
Step 5 (Sound & Launch) Select and press the Lower button (sound
& launch). Then the green light turns orange.
Step 6 - Press and hold the Gun
Button for 5 seconds on the DG.
Orange light changes to flashing
green. You are now paired and the
Master Transmitter is in Dog & Gun
mode.
17
Wet Weather Training
The transmitter is 100% waterproof, and the receiver is water resistant and can be used in the rain. The
receiver should never be immersed in water. During continued water-work, the inside of the Bumper tube
should be dry. If the tube is wet, a loss of power may occur. Drying can be accomplished by spinning the
Bumper by the power handle and throw rope, or by using a drying rack to let the water drain out, or by using
a shotgun brush with a cloth or shammy material wrapped around it.
Maintaining your Bumper Boy
•
•
•
•
Every 5 days, use dry Graphite to lubricate. This is a must for good operation and servo life.
If “O”-rings roll off, use silicon grease to lubricate.
Make sure you have a test servo. This may be required for testing or as a back-up.
Watch video maintenance and operation (bumperboy.com/support.php)
Test Kit
This is a must; it allows you to test, and trouble shoot. It saves time; there’s no
need to ever spend the money to send units in for repair. The kit can get you
back up and training in 10 minutes.
18
Bumper Care
Keep the bumpers clean. Clear accumulated grit and carbon from the bumper tube with a 12 gauge
shotgun soft cleaning tip.
Launcher Care
Keep launcher components clean. Check to ensure the nuts securing the launcher frame components are
secure. Periodically (every three to six months) clean accumulated carbon and grit from the launcher barrel
with a .22 calibre cleaning rod and cleaning patch. Clean the exterior of the launcher barrel. Apply a small
amount of silicone grease to the “O”-rings on the launcher barrels monthly. This is used for O-rings and to
stop the bumper from getting stuck on the barrel.
Trouble Shooting
All Bumper Boys are designed to be repaired in the field, with very basic skills and knowledge. Please review
the videos on the support page of www.bumperboy.com (www.bumperboy.com/support.php) and also
see below.
Confirming electronics are working
•
•
•
•
Make sure the launcher is not cocked or loaded
Press the launch key and see it the light comes on, indicating a signal was received
If no indicating light comes on, press reload and test again
Try using another selection dial setting; you may have paired this unit to another selector number.
Re-check your pairing.
Servo not working but electronics are
• The most common problem is a loose main wiring harness in the receiver. Unplug and re-plug
(make sure you press the latch in on the connector to release) until the harness is firm and is snapped
in, checking the pins inside the plug to make sure they are level with one another. Retry test firing
without cocking firing pins. Push reload button.
• Second most common problem – The firing assembly has been spun around and caused the
connector to be pulled out. You will have to remove the heat shrink and check to see if the pins are
level with one another. See replacing servo to check connection
• Use pliers to align pins and reconnect. New heat shrink should be used to repair, and refer to
replacing a servo for more information
Servo works sometimes
•
•
•
•
Loose main wiring harness- check, remove and reconnect
Cut wire – see replace servo
Poor lubrication – see lubrication details
Bad servo – see replace servo
Intermittent at a distance only
• Recharge your unit, try again.
• Possible transmitter problem – test at 1 yard and than at 200 yards
Servo releasing firing pin but not firing (no dent in shell)
• Poor lubrication
• Never leave firing pins cocked
19
Fires but no power
• Water or dirt issue – clean, drain or use a second set of bumpers and fire again without bumpers
• Gun powder builds up. Make sure you use wadded shells, once you get a misfire
• Do not use grease or oil-based products on the bumpers or firing tubes.
Replacing servos
If a servo motor needs to be replaced, they can be purchased from Bumper Boy.
See video at www.bumperboy.com/support.php
1. Score heat shrink, on both sides, at servo connector, located approximately 11 inches back from
the servo motor
2. Pull apart wiring harness from connector
3. Remove the four servo mounting screws, and then remove the servo
4. NOTE – If you purchased our servo, go to step 8
5. Remove servo arm and bracket from old servo
6. Place bracket in position (on new servo)
7. Re-install servo arm, making sure that it is put back in the same position from which it was
removed (from the old servo)
8. Re-install the new servo by inserting four servo mounting screws (do not put servo washers back
on, and do not over tighten)
9. Slide the heat shrink over the wiring harness, and then plug new servo into wiring harness, and
make sure to match the wiring harness colors (match white to white), and press the ends together.
10. Test servo with the electronics. If the servo doesn’t activate, reverse the connector.
11. Use a heat gun, or lighter to secure the heat shrink.
Checking servo alignment
Servo alignment is very important as an improperly aligned servo will interfere with the firing pin engaging
properly. You should always check after cocking that there’s an 1/8th of an inch gap.
1. Remove servo arm by removing the center
screw and pulling the arm straight up.
2. Reset the servo arm to its default starting
position by pushing the Pair button.
3. Hold the arm at the 50 degree angle (see
picture) and push the arm back down onto
the servo.
4. Replace the center screw.
Replacing Wiring Harness
Squeeze the tab on the back of the connector and pull down to unplug the wiring harness from the receiver
(pliers may be required). Each servo wire must be disconnected from the old wiring harness. Follow
the instructions on “replacing a servo” to do so- the connector is under the heat shrink. Once you have
disconnected all the servos from the old wiring harness, you must reconnect them onto the new wiring
harness (white wire to white wire). Test.
20
FCC COMPLIANCE
The manufacturing of Bumper Boy Inc. remote trainers involves exacting production methods, precise
tuning, and the highest quality control tests. In addition, these products are manufactured to operate
within Federal Communication Commission (FCC) specifications. It is a violation of FCC rules to modify your
equipment. Bumper Boy Inc. verifies its products to operate under Part 95 of FCC regulations. Unauthorized
modifications to your equipment could result in it not meeting specifications and thus violating FCC
regulations. Any and all adjustments should be performed only by technically qualified personnel
authorized by Bumper Boy Inc. To continue to meet FCC operating specifications, any replacement of circuit
components, including antennas, must meet Bumper Boy Inc. manufacturing specifications. This device
complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Patents
Certain products are covered by one or more of these U.S. patent numbers or patent pending:
6,708,649; 6,830,014; 7,267,082; 7,243,617; 7,562,640; 7,958,877; 12/484,008
Battery Disposal
The lithium-Ion battery contained in this device should never be charged with an incompatible charger.
Never puncture, short-circuit, deform, or incinerate as this could cause fire, an explosion, bodily harm, or
property damage.
Terms of Use and Limitation of Liability
1. Terms of use
This product is offered to you conditioned upon your acceptance without modification of the terms,
conditions and notices contained herein. Usage of this product implies acceptance of all such terms,
conditions, and notices.
2. Proper use
This product is designed for training dogs. The specific temperament of your dog may not work with this
product. We recommend that you not use this product if your dog is less than 8 pounds, or if your dog is
aggressive. If you are unsure whether this is appropriate for your dog, please consult your veterinarian or
certified trainer. You can also contact our customer service representative at 1-800-610-4299.
3. No unlawful or prohibited use
This product is designed for use with dogs only. This dog training device is not intended to harm, injure, or
provoke. Using this product in a way that is not intended could result in violation of Federal, State or local
laws
4. Limitation of liability
In no event shall Bumper Boy Inc. be liable for any direct, indirect, punitive, incidental, special or
consequential damages. Bumper Boy Inc. shall not be liable for any damages arising out of or connected
with the use or misuse of this product. The buyer assumes all risks and liability from the use of this product.
5. Modification of terms and conditions
Bumper Boy Inc. reserves the right to change the terms, conditions and notices under which this product
is offered.
Version 1.1
21